Also updated maintainer info.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

In the case when an ep_connect request is interrupted due to route
request stall, if the iSCSI daemon is terminated by the user, the chip
will be left in a state which will not get cleaned up upon module
removal.  Upon module reload, when the same context id is used for a
new connection, chip panic would occur.

This patch adds chip cleanup in the module removal path.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Acked-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Specific to the Broadcom 10g chipset, the CFC delete operation must be
coupled with the cm_abort/close with does the SRC delete/terminate offload
operation prior.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Expanded the TMF request routine to support other TMFs such as LUN
RESET, etc.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NAnil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

According to RFC3720, nopout packet sent in response to unsolicited
nopin packet requesting a response must retain the TTT of the requester.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Bump the driver version.
Signed-off-by: NWayne Boyer <wayneb@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch fixes a resource address formatting problem where the first byte
was being zeroed out.

Also, the device ID is now made available as a sysfs attribute.
Signed-off-by: NWayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NKaren Xie <kxie@chelsio.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Added cxgb4i iSCSI driver.

This patch implements the cxgb4i iscsi connection acceleration for the
open-iscsi initiator.

The cxgb4i driver offers the iscsi PDU based offload:
- digest insertion and verification
- payload direct-placement into host memory buffer.
Signed-off-by: NKaren Xie <kxie@chelsio.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

[PATCH v5 1/3] libcxgbi: common library for cxgb3i and cxgb4i

From: Karen Xie <kxie@chelsio.com>

Extracts common functions to libcxgbi.
Signed-off-by: NKaren Xie <kxie@chelsio.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

In lpfc_cleanup_pending_mbox() we already have IRQs disabled so we don't
need to disable them again.

Also in lpfc_sli_intr_handler() there is a typo where it has
spin_unlock_irq() instead of just spin_unlock().
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Outdent the code following the if.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@

(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

if (p1[0].column == p2[0].column):
  cocci.print_main("branch",p1)
  cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NNick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.

Patch has only been compile tested.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.

Patch has only been compile tested.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch adds a fc_host setting to store the
default dev_loss_tmo. It is used if the driver
has a callack to get the value from the LLD. If
the callback is not set, then we use the fc class
module default value.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

gcc-4.0.2:

  drivers/scsi/qla4xxx/ql4_os.c: In function 'qla4_8xxx_error_recovery':
  drivers/scsi/qla4xxx/ql4_glbl.h:135: sorry, unimplemented: inlining failed in call to 'qla4_8xxx_set_drv_active': function body not available
  drivers/scsi/qla4xxx/ql4_os.c:2377: sorry, unimplemented: called from here
  drivers/scsi/qla4xxx/ql4_glbl.h:135: sorry, unimplemented: inlining failed in call to 'qla4_8xxx_set_drv_active': function body not available
  drivers/scsi/qla4xxx/ql4_os.c:2393: sorry, unimplemented: called from here

Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver is the only user of dma_is_consistent().  We plan to remove this
API.

The driver uses the API in the following way:

BUG_ON(!dma_is_consistent(hostdata->dev, pScript) && L1_CACHE_BYTES < dma_get_cache_alignment());

The above code tries to see if L1_CACHE_BYTES is greater than
dma_get_cache_alignment() on sysmtes that can not allocate coherent memory
(some old systems can't).

James Bottomley exmplained that this is necesary because the driver packs the
set of mailboxes into a single coherent area and separates the different
usages by a L1 cache stride.  So it's fatal if the dma

He also pointed out that we can kill this checking because we don't hit this
BUG_ON on all architectures that actually use the driver.

(akpm: stolen from the scsi tree because
dma-mapping-remove-dma_is_consistent-api.patch needs it)
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAndy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Adaptec OEM Raid Solutions <aacraid@adaptec.com>
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Cc: James Smart <james.smart@emulex.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use memdup_user when user data is immediately copied into the
allocated region.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A couple of scsi drivers define a BIT() macro, duplicating the one in
bitops.h.

Cc: Jing Huang <huangj@brocade.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

bnx2i should depend on NET since it selects SCSI_ISCSI_ATTRS, which
depends on NET.

Also move the dependencies together.

The "depends" change fixes multiple build errors when CONFIG_NET is
not enabled:
ERROR: "skb_trim" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "netlink_kernel_create" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "netlink_kernel_release" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "skb_pull" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "init_net" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "__alloc_skb" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "netlink_broadcast" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "kfree_skb" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "skb_put" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Anil Veerabhadrappa <anilgv@broadcom.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

pmcraid should depend on NET since it uses netlink interfaces.
This fixes multiple build errors when CONFIG_NET is not enabled:

ERROR: "genl_register_family" [drivers/scsi/pmcraid.ko] undefined!
ERROR: "genl_unregister_family" [drivers/scsi/pmcraid.ko] undefined!
ERROR: "nla_put" [drivers/scsi/pmcraid.ko] undefined!
ERROR: "init_net" [drivers/scsi/pmcraid.ko] undefined!
ERROR: "__alloc_skb" [drivers/scsi/pmcraid.ko] undefined!
ERROR: "netlink_broadcast" [drivers/scsi/pmcraid.ko] undefined!
ERROR: "kfree_skb" [drivers/scsi/pmcraid.ko] undefined!
ERROR: "skb_put" [drivers/scsi/pmcraid.ko] undefined!
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It appears that the wrong fcport H2I message was tested
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NJing Huang <huangj@Brocade.COM>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It's an exported symbol of kernel/printk.c

Rename vprintk and dprintk macros to more common VPRINTK and DPRINTK
Add do { } while(0) around macros
Add level to VPRINTK so KERN_CONT can be used a couple of times.
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use DECLARE_WAIT_QUEUE_HEAD_ONSTACK to make lockdep happy
Signed-off-by: NYong Zhang <yong.zhang0@gmail.com>
Cc: Jing Huang <huangj@brocade.com>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

String constants that are continued on subsequent lines with \ will cause
spurious whitespace in the resulting output.
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In sd_store_cache_type the symbol 'len' is declared twice.  Remove the
second declaration to quiet the following sparse warning.

warning: symbol 'len' shadows an earlier one

In sd_probe the variable 'index' is declared as a u32.  This variable is
used in a call to ida_get_new which is expecting an int *.  Make the
variable an int to quiet the following sparse warning.

warning: incorrect type in argument 2 (different signedness)

There are 4 symbols in the file that are not exported and produce
the following sparse warnings.

warning: symbol 'sd_cdb_cache' was not declared. Should it be static?
warning: symbol 'sd_cdb_pool' was not declared. Should it be static?
warning: symbol 'sd_read_protection_type' was not declared. Should it be static?
warning: symbol 'sd_read_app_tag_own' was not declared. Should it be static?

Make them static to quiet the warnings.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Dan's list included:

drivers/scsi/scsi_lib.c +1365 scsi_kill_request(9) warning: variable derefenced in initializer 'cmd'
drivers/scsi/scsi_lib.c +1365 scsi_kill_request(9) warning: variable derefenced before check 'cmd'

We dereference cmd (and possible OOPS if cmd == NULL) before starting the
request so just remove the superfluous debugging code altogether.

[ bart: the potential NULL pointer dereference was finally fixed in
  (much later than mine) commit 03b14708 but my patch is still valid ]
Reported-by: NDan Carpenter <error27@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Eugene Teo <eteo@redhat.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In each case, the destination of the allocation has type struct **, so the
elements of the array should have pointer type, not structure type.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@disable sizeof_type_expr@
type T;
T **x;
@@

  x =
  <+...sizeof(
- T
+ *x
  )...+>
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: Rolf Eike Beer <eike-kernel@sf-tec.de>
Cc: Joe Perches <joe@perches.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The tag_number reaches dcb->max_command + 1 after the loop, but when
the tag_number equals dcb->max_command an error message is already
issued. The last iteration therefore appears obsolete.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The ifdefs are broken so the MMIO code is never compiled and so it's
broken too.  Fix them all.  Untested as I don't have the hardware.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Reviewed-by: NAndy Walls <awalls@md.metrocast.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove misleading error message that appears after pnp card has been
detected correctly.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

At the point where cmnd is initialized, it is tested for NULL, so it
doesn't have to be tested again here.

A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):

// <smpl>
@match exists@
expression x, E;
identifier fld;
@@

* x->fld
  ... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Besides keeping the line short, the second setting of the MR_DMA_MODE bit
was removed.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

unmap ccb_phys as well when scsi_add_host() fails
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: Achim Leubner <achim_leubner@adaptec.com>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Check whether index is within bounds before testing the element.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: Willem Riede <osst@riede.org>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since the writing to sysfs can free the old one, we need to block that
when we access the charp variables.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Reviewed-by: NTakashi Iwai <tiwai@suse.de>
Tested-by: NPhil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Jing Huang <huangj@brocade.com>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: linux-usb@vger.kernel.org