Use skb_checksum_validate to verify checksum.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This replaces 6 identical code snippets with a call to a new
static inline function.
Signed-off-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit c15b1cca ("ipv6: move DAD and addrconf_verify
processing to workqueue") some counters are now updated in process context
and thus need to disable bh before doing so, otherwise deadlocks can
happen on 32-bit archs. Fabio Estevam noticed this while while mounting
a NFS volume on an ARM board.

As a compensation for missing this I looked after the other *_STATS_BH
and found three other calls which need updating:

1) icmp6_send: ip6_fragment -> icmpv6_send -> icmp6_send (error handling)
2) ip6_push_pending_frames: rawv6_sendmsg -> rawv6_push_pending_frames -> ...
   (only in case of icmp protocol with raw sockets in error handling)
3) ping6_v6_sendmsg (error handling)

Fixes: c15b1cca ("ipv6: move DAD and addrconf_verify processing to workqueue")
Reported-by: NFabio Estevam <festevam@gmail.com>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch 446fab59 ("ipv6: enable anycast addresses
as source addresses in ICMPv6 error messages") causes an Oops when pinging a not
set up IPv6 peer on a sit tunnel.

The problem is that ipv6_anycast_destination() uses unconditionally skb_dst(skb),
which is NULL in this case.

The solution is to use instead the ipv6_chk_acast_addr_src() function.

Here are the steps to reproduce it:
modprobe sit
ip link add sit1 type sit remote 10.16.0.121 local 10.16.0.249
ip l s sit1 up
ip -6 a a dev sit1 2001:1234::123 remote 2001:1234::121
ping6 2001:1234::121
Reported-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NFrancois-Xavier Le Bail <fx.lebail@yahoo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Uses ipv6_anycast_destination() in icmp6_send().
Suggested-by: NBill Fink <billfink@mindspring.com>
Signed-off-by: NFrancois-Xavier Le Bail <fx.lebail@yahoo.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change move anycast_src_echo_reply sysctl with other ipv6 sysctls.
Suggested-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NFrancois-Xavier Le Bail <fx.lebail@yahoo.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Suggested-by: NSimon Schneider <simon-schneider@gmx.net>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change allows to follow a recommandation of RFC4942.

- Add "anycast_src_echo_reply" sysctl to control the use of anycast addresses
  as source addresses for ICMPv6 echo reply. This sysctl is false by default
  to preserve existing behavior.
- Add inline check ipv6_anycast_destination().
- Use them in icmpv6_echo_reply().

Reference:
RFC4942 - IPv6 Transition/Coexistence Security Considerations
   (http://tools.ietf.org/html/rfc4942#section-2.1.6)

2.1.6. Anycast Traffic Identification and Security

   [...]
   To avoid exposing knowledge about the internal structure of the
   network, it is recommended that anycast servers now take advantage of
   the ability to return responses with the anycast address as the
   source address if possible.
Signed-off-by: NFrancois-Xavier Le Bail <fx.lebail@yahoo.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Running 'make namespacecheck' shows:
  net/ipv6/route.o
    ipv6_route_table_template
    rt6_bind_peer
  net/ipv6/icmp.o
    icmpv6_route_lookup
    ipv6_icmp_table_template

This addresses some of those warnings by:
 * make icmpv6_route_lookup static
 * move inline's out of ip6_route.h since only used into route.c
 * move rt6_bind_peer into route.c
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC 4861 says that the IP source address of the Redirect is the
same as the current first-hop router for the specified ICMP
Destination Address, so the gateway should be taken into
consideration when we find the route for redirect.

There was once a check in commit
a6279458 ("NDISC: Search over
all possible rules on receipt of redirect.") and the check
went away in commit b94f1c09
("ipv6: Use icmpv6_notify() to propagate redirect, instead of
rt6_redirect()").

The bug is only "exploitable" on layer-2 because the source
address of the redirect is checked to be a valid link-local
address but it makes spoofing a lot easier in the same L2
domain nonetheless.

Thanks very much for Hannes's help.
Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC 4443 has defined two additional codes for ICMPv6 type 1 (destination
unreachable) messages:
        5 - Source address failed ingress/egress policy
	6 - Reject route to destination

Now they are treated as protocol error and icmpv6_err_convert() converts them
to EPROTO.

RFC 4443 says:
	"Codes 5 and 6 are more informative subsets of code 1."

Treat codes 5 and 6 as code 1 (EACCES)

Btw, connect() returning -EPROTO confuses firefox, so that fallback to
other/IPv4 addresses does not work:
https://bugzilla.mozilla.org/show_bug.cgi?id=910773Signed-off-by: NJiri Bohac <jbohac@suse.cz>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce the uses of this unnecessary typedef.

Done via perl script:

$ git grep --name-only -w ctl_table net | \
  xargs perl -p -i -e '\
	sub trim { my ($local) = @_; $local =~ s/(^\s+|\s+$)//g; return $local; } \
        s/\b(?<!struct\s)ctl_table\b(\s*\*\s*|\s+\w+)/"struct ctl_table " . trim($1)/ge'

Reflow the modified lines that now exceed 80 columns.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case skb->tail will be a pointer whereas skb->transport_header
will be an offset from head. This is corrected by using wrappers that
ensure that comparisons and calculations are always made using pointers.
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the ability to send ICMPv6 echo requests without a
raw socket. The equivalent ability for ICMPv4 was added in
2011.

Instead of having separate code paths for IPv4 and IPv6, make
most of the code in net/ipv4/ping.c dual-stack and only add a
few IPv6-specific bits (like the protocol definition) to a new
net/ipv6/ping.c. Hopefully this will reduce divergence and/or
duplication of bugs in the future.

Caveats:

- Setting options via ancillary data (e.g., using IPV6_PKTINFO
  to specify the outgoing interface) is not yet supported.
- There are no separate security settings for IPv4 and IPv6;
  everything is controlled by /proc/net/ipv4/ping_group_range.
- The proc interface does not yet display IPv6 ping sockets
  properly.

Tested with a patched copy of ping6 and using raw socket calls.
Compiles and works with all of CONFIG_IPV6={n,m,y}.
Signed-off-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add MIB counters for checksum errors in IP layer,
and TCP/UDP/ICMP layers, to help diagnose problems.

$ nstat -a | grep  Csum
IcmpInCsumErrors                72                 0.0
TcpInCsumErrors                 382                0.0
UdpInCsumErrors                 463221             0.0
Icmp6InCsumErrors               75                 0.0
Udp6InCsumErrors                173442             0.0
IpExtInCsumErrors               10884              0.0
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following patch adds icmp-registration module for ipv6.  It allows
ipv6 protocol to register icmp_sender which is used for sending
ipv6 icmp msgs.  This extra layer allows us to kill ipv6 dependency
for sending icmp packets.

This patch also fixes ip_tunnel compilation problem when ip_tunnel
is statically compiled in kernel but ipv6 is module
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch requires multicast interface-scoped addresses to supply a
sin6_scope_id. Because the sin6_scope_id is now also correctly used
in case of interface-scoped multicast traffic this enables one to use
interface scoped addresses over interfaces which are not targeted by the
default multicast route (the route has to be put there manually, though).

getsockname() and getpeername() now return the correct sin6_scope_id in
case of interface-local mc addresses.

v2:
a) rebased ontop of patch 1/4 (now uses ipv6_addr_props)

v3:
a) reverted changes for ipv6_addr_props

v4:
a) unchanged

Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>dave
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pmtu and redirect events are now handled in the protocols error handler,
so add an error handler for icmp6 to do this. It is needed in the case
when we have no socket context. Based on a patch by Duan Jiong.
Reported-by: NDuan Jiong <djduanjiong@gmail.com>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Enable the per device ipv4 sysctls:
   net/ipv4/conf/<if>/forwarding
   net/ipv4/conf/<if>/mc_forwarding
   net/ipv4/conf/<if>/accept_redirects
   net/ipv4/conf/<if>/secure_redirects
   net/ipv4/conf/<if>/shared_media
   net/ipv4/conf/<if>/rp_filter
   net/ipv4/conf/<if>/send_redirects
   net/ipv4/conf/<if>/accept_source_route
   net/ipv4/conf/<if>/accept_local
   net/ipv4/conf/<if>/src_valid_mark
   net/ipv4/conf/<if>/proxy_arp
   net/ipv4/conf/<if>/medium_id
   net/ipv4/conf/<if>/bootp_relay
   net/ipv4/conf/<if>/log_martians
   net/ipv4/conf/<if>/tag
   net/ipv4/conf/<if>/arp_filter
   net/ipv4/conf/<if>/arp_announce
   net/ipv4/conf/<if>/arp_ignore
   net/ipv4/conf/<if>/arp_accept
   net/ipv4/conf/<if>/arp_notify
   net/ipv4/conf/<if>/proxy_arp_pvlan
   net/ipv4/conf/<if>/disable_xfrm
   net/ipv4/conf/<if>/disable_policy
   net/ipv4/conf/<if>/force_igmp_version
   net/ipv4/conf/<if>/promote_secondaries
   net/ipv4/conf/<if>/route_localnet

- Enable the global ipv4 sysctl:
   net/ipv4/ip_forward

- Enable the per device ipv6 sysctls:
   net/ipv6/conf/<if>/forwarding
   net/ipv6/conf/<if>/hop_limit
   net/ipv6/conf/<if>/mtu
   net/ipv6/conf/<if>/accept_ra
   net/ipv6/conf/<if>/accept_redirects
   net/ipv6/conf/<if>/autoconf
   net/ipv6/conf/<if>/dad_transmits
   net/ipv6/conf/<if>/router_solicitations
   net/ipv6/conf/<if>/router_solicitation_interval
   net/ipv6/conf/<if>/router_solicitation_delay
   net/ipv6/conf/<if>/force_mld_version
   net/ipv6/conf/<if>/use_tempaddr
   net/ipv6/conf/<if>/temp_valid_lft
   net/ipv6/conf/<if>/temp_prefered_lft
   net/ipv6/conf/<if>/regen_max_retry
   net/ipv6/conf/<if>/max_desync_factor
   net/ipv6/conf/<if>/max_addresses
   net/ipv6/conf/<if>/accept_ra_defrtr
   net/ipv6/conf/<if>/accept_ra_pinfo
   net/ipv6/conf/<if>/accept_ra_rtr_pref
   net/ipv6/conf/<if>/router_probe_interval
   net/ipv6/conf/<if>/accept_ra_rt_info_max_plen
   net/ipv6/conf/<if>/proxy_ndp
   net/ipv6/conf/<if>/accept_source_route
   net/ipv6/conf/<if>/optimistic_dad
   net/ipv6/conf/<if>/mc_forwarding
   net/ipv6/conf/<if>/disable_ipv6
   net/ipv6/conf/<if>/accept_dad
   net/ipv6/conf/<if>/force_tllao

- Enable the global ipv6 sysctls:
   net/ipv6/bindv6only
   net/ipv6/icmp/ratelimit
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for supporting the creation of network namespaces
by unprivileged users, modify all of the per net sysctl exports
and refuse to allow them to unprivileged users.

This makes it safe for unprivileged users in general to access
per net sysctls, and allows sysctls to be exported to unprivileged
users on an individual basis as they are deemed safe.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

#if defined(CONFIG_FOO) || defined(CONFIG_FOO_MODULE)

can be replaced by

#if IS_ENABLED(CONFIG_FOO)

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And delete rt6_redirect(), since it is no longer used.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only use it in the absolutely required cases:

1) COW'ing metrics

2) ipv4 PMTU

3) ipv4 redirects
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't pretend that inet_protos[] and inet6_protos[] are hashes, thay
are just a straight arrays.  Remove all unnecessary hash masking.

Document MAX_INET_PROTOS.

Use RAW_HTABLE_SIZE when appropriate.
Reported-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One tricky issue on the ipv6 side vs. ipv4 is that the ICMP callouts
to handle the error pass the 32-bit info cookie in network byte order
whereas ipv4 passes it around in host byte order.

Like the ipv4 side, we have two helper functions.  One for when we
have a socket context and one for when we do not.

ip6ip6 tunnels are not handled here, because they handle PMTU events
by essentially relaying another ICMP packet-too-big message back to
the original sender.

This patch allows us to get rid of rt6_do_pmtu_disc().  It handles all
kinds of situations that simply cannot happen when we do the PMTU
update directly using a fully resolved route.

In fact, the "plen == 128" check in ip6_rt_update_pmtu() can very
likely be removed or changed into a BUG_ON() check.  We should never
have a prefixed ipv6 route when we get there.

Another piece of strange history here is that TCP and DCCP, unlike in
ipv4, never invoke the update_pmtu() method from their ICMP error
handlers.  This is incredibly astonishing since this is the context
where we have the most accurate context in which to make a PMTU
update, namely we have a fully connected socket and associated cached
socket route.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a lot of places that open-code rt{,6}_get_peer() only because
they want to set 'create' to one.  So add an rt{,6}_get_peer_create()
for their sake.

There were also a few spots open-coding plain rt{,6}_get_peer() and
those are transformed here as well.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mostly bool conversions, some inline removals and const additions.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add #define pr_fmt(fmt) as appropriate.

Add "IPv6: " to appropriate files.

Convert printk(KERN_<LEVEL> to pr_<level> (but not KERN_DEBUG).
Standardize on "%s: " not "%s(): " when emitting __func__.
Use "%s: ", __func__ instead of embedding function name.
Coalesce formats, align arguments.

ADDRCONF output is now prefixed with "IPv6: "
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

icmp.c:501: ERROR: "(foo*)" should be "(foo *)"
icmp.c:582: ERROR: "(foo*)" should be "(foo *)"
icmp.c:954: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: NEldad Zack <eldad@fogrefinery.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove all #inclusions of asm/system.h preparatory to splitting and killing
it.  Performed with the following command:

perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: NDavid Howells <dhowells@redhat.com>

The IPV6_UNICAST_IF feature is the IPv6 compliment to IP_UNICAST_IF.
Signed-off-by: NErich E. Hoover <ehoover@mines.edu>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While parsing through IPv6 extension headers, fragment headers are
skipped making them invisible to the caller.  This reports the
fragment offset of the last header in order to make it possible to
determine whether the packet is fragmented and, if so whether it is
a first or last fragment.
Signed-off-by: NJesse Gross <jesse@nicira.com>

C assignment can handle struct in6_addr copying.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb truesize currently accounts for sk_buff struct and part of skb head.
kmalloc() roundings are also ignored.

Considering that skb_shared_info is larger than sk_buff, its time to
take it into account for better memory accounting.

This patch introduces SKB_TRUESIZE(X) macro to centralize various
assumptions into a single place.

At skb alloc phase, we put skb_shared_info struct at the exact end of
skb head, to allow a better use of memory (lowering number of
reallocations), since kmalloc() gives us power-of-two memory blocks.

Unless SLUB/SLUB debug is active, both skb->head and skb_shared_info are
aligned to cache lines, as before.

Note: This patch might trigger performance regressions because of
misconfigured protocol stacks, hitting per socket or global memory
limits that were previously not reached. But its a necessary step for a
more accurate memory accounting.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Andi Kleen <ak@linux.intel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ICMP and ND are not fast path, but still we can avoid changing idev
refcount, using RCU.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create two sets of port member accessors, one set prefixed by fl4_*
and the other prefixed by fl6_*

This will let us to create AF optimal flow instances.

It will work because every context in which we access the ports,
we have to be fully aware of which AF the flowi is anyways.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I intend to turn struct flowi into a union of AF specific flowi
structs.  There will be a common structure that each variant includes
first, much like struct sock_common.

This is the first step to move in that direction.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>