Add Device ID of Intel BayTrail SMBus Controller.
Signed-off-by: NChew, Kean ho <kean.ho.chew@intel.com>
Signed-off-by: NChew, Chiau Ee <chiau.ee.chew@intel.com>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Commit 370136bc ("i2c: mv64xxx: Add reset deassert call")
introduced:

drivers/video/Kconfig:42:error: recursive dependency detected!

ARCH_SUNXI selects RESET_CONTROLLER anyhow.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The Allwinner A31 SoC using that IP has a reset controller maintaining
it reset unless told otherwise.

Add some optional reset support to the driver.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The locations of SMBus register base address and enablement bit are changed
from AMD ML, which need this patch to be supported.
Signed-off-by: NShane Huang <shane.huang@amd.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org

OSIF, Open Source InterFace, is a USB based i2c bus master.  The
origional design was based on i2c-tiny-usb, but more modern versions
of the firmware running on the MegaAVR microcontroller use a different
protocol over the USB. This code is based on Barry Carter
<barry.carter@gmail.com> driver.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Since 93abe8e4 (clk: add non CONFIG_HAVE_CLK routines) code using clk.h
like this platform driver need not depend on HAVE_CLK. Also, remove a
redundant clk.h include from core driver.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Hardware supported by the i2c sh_mobile and rcar drivers is only found
on SUPERH or ARCH_SHMOBILE platforms. Restrict non-COMPILE_TEST
compilation to them.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Tested with a r7s72100 genmai board acessing an eeprom.
Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Introduce support for Broadcom Serial Controller (BSC) I2C bus found
in the Kona family of Mobile SoCs.  FIFO hardware is utilized but only
standard mode (100kHz), fast mode (400kHz), fast mode plus (1MHz), and
I2C high-speed (3.4 MHz) bus speeds are supported.
Signed-off-by: NTim Kryger <tim.kryger@linaro.org>
Reviewed-by: NMatt Porter <matt.porter@linaro.org>
Reviewed-by: NMarkus Mayer <markus.mayer@linaro.org>
[wsa: fixed Kconfig sorting, squashed broken out patches into one]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds the SMBus Device IDs for the Intel Wildcat Point-LP PCH.
Signed-off-by: NJames Ralston <james.d.ralston@intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds support to SSC (Synchronous Serial Controller)
I2C driver. This IP also supports SPI protocol, but this is not
the aim of this driver.

This IP is embedded in all ST SoCs for Set-top box platorms, and
supports I2C Standard and Fast modes.
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Adds support for High Speed I2C driver found in Exynos5 and
later SoCs from Samsung.

Driver only supports Device Tree method.
Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: NTaekgyun Ko <taeggyun.ko@samsung.com>
Reviewed-by: NSimon Glass <sjg@google.com>
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: NAndrew Bresticker <abrestic@google.com>
[wsa: rebased to v3.12-rc4 (no of_i2c.h anymore)]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Renesas ARM platforms are transitioning from single-platform to
multi-platform kernels using the new ARCH_SHMOBILE_MULTI. Make the
driver available on all ARM platforms to enable it on both ARCH_SHMOBILE
and ARCH_SHMOBILE_MULTI, and increase build testing coverage with
COMPILE_TEST.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Keystone SOCs uses the same I2C IP as available on DaVinci SOCs.
Update the config so that ARCH_KEYSTONE can use it.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add i2c support for the on-board PLD found on some Kontron embedded
modules.

Originally-From: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: NKevin Strasser <kevin.strasser@linux.intel.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NDarren Hart <dvhart@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds the i801 SMBus Controller DeviceIDs for the Intel Coleto Creek PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

I got a build error today that made me realize that it is not
possible to build a kernel for a SiRF platform without enabling
CONFIG_PRIMA2, since a lot of common code depends on CONFIG_PRIMA2.

This fixes all occurences that appear like common SiRF code.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NMark Brown <broonie@linaro.org>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NBarry Song <Baohua.Song@csr.com>
Acked-by: NMike Turquette <mturquette@linaro.org>

Add the compatible string for the Allwinner A10 i2c controller and the
associated register layout.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch adds support for the I2C bus controllers found on Wondermedia
8xxx-series SoCs. Only master-mode is supported.
Signed-off-by: NTony Prisk <linux@prisktech.co.nz>
[wsa: fixed one macro to shift 8 instead of 16]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

CAVIUM_OCTEON_SOC most place we used to use CPU_CAVIUM_OCTEON.  This
allows us to CPU_CAVIUM_OCTEON in places where we have no OCTEON SOC.

Remove CAVIUM_OCTEON_SIMULATOR as it doesn't really do anything, we can
get the same configuration with CAVIUM_OCTEON_SOC.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-edac@vger.kernel.org
Cc: linux-i2c@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: spi-devel-general@lists.sourceforge.net
Cc: devel@driverdev.osuosl.org
Cc: linux-usb@vger.kernel.org
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Patchwork: https://patchwork.linux-mips.org/patch/5295/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Moorestown support is removed from kernel and Medfield is supported by
i2c-designware-pci. But i2c-intel-mid is still in upstream and community
resources are wasted to maintain it.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

To add AMD CZ SMBus controller device ID.

[bhelgaas: drop pci_ids.h update]
Signed-off-by: NShane Huang <shane.huang@amd.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NTejun Heo <tj@kernel.org>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org

GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

Remove !S390 dependency from i2c Kconfig, since s390 now supports PCI, HAS_IOMEM
and HAS_DMA, however we need to add a couple of GENERIC_HARDIRQS dependecies to
fix compile and link errors like these:

ERROR: "devm_request_threaded_irq" [drivers/i2c/i2c-smbus.ko] undefined!
ERROR: "devm_request_threaded_irq" [drivers/i2c/busses/i2c-ocores.ko] undefined!

Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch adds the SMBus Device IDs for the Intel Wellsburg PCH
Signed-off-by: NJames Ralston <james.d.ralston@intel.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

This implements a very basic I2C host driver for the BCM2835 SoC. Missing
features so far are:

* 10-bit addressing.
* DMA.
Reviewed-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

Signed-off-by: NAmaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

The iSMT (Intel SMBus Message Transport) supports multi-master I2C/SMBus,
as well as IPMI.  It's operation is DMA-based and utilizes descriptors to
initiate transactions on the bus.

The iSMT hardware can act as both a master and a target, although this
driver only supports being a master.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NBill Brown <bill.e.brown@intel.com>
Tested-by: NSeth Heasley <seth.heasley@intel.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <wolfram@the-dreams.de>

This patch adds the PCU SMBus DeviceID for the Intel Avoton SOC.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Reviewed-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.

CC: Ralf Baechle <ralf@linux-mips.org>
CC: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.

The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer.  Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.

bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY.  The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.

add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function                                     old     new   delta
chr_dev_init                                 166     170      +4
allow_signal                                  80      82      +2
static.__warned                              143     142      -1
disallow_signal                               63      62      -1
__set_special_pids                            95      94      -1
unregister_console                           126     121      -5
start_kernel                                 546     541      -5
register_console                             593     588      -5
copy_from_user                                45      40      -5
sys_setsid                                   128     120      -8
sys_vhangup                                   32      19     -13
do_exit                                     1543    1526     -17
bitmap_zero                                   60      40     -20
arch_local_irq_save                          137     117     -20
release_task                                 674     652     -22
static.spin_unlock_irqrestore                308     260     -48
Signed-off-by: NJoe Millenbach <jmillenbach@gmail.com>
Reviewed-by: NJamey Sharp <jamey@minilop.net>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds the mfd cell to use the i2c part of the Nano River Technologies
viperboard as i2c master.
Signed-off-by: NLars Poeschel <poeschel@lemonage.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add i2c driver to enable access to devices behind CBUS on Nokia Internet
Tablets.

The patch also adds CBUS I2C configuration for N8x0 which is one of the
users of this driver.
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Arbitrarily selecting GPIOLIB causes trouble on some architectures,
so don't do that. Instead, just make the optional multiplexing code
depend on CONFIG_I2C_MUX_GPIO instead of CONFIG_I2C_MUX for now. We
can revisit if the i2c-i801 driver ever supports other multiplexing
flavors.

Also make that optional code depend on DMI, as it won't do anything
without that.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>

R-Car I2C is similar with SH7760 I2C.
But the SH7760 I2C driver had many workaround operations, since H/W had bugs.
Thus, it was pointless to keep compatible between SH7760 and R-Car I2C drivers.
This patch creates new Renesas R-Car I2C driver.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>

Add support for SMBus multiplexing on Asus Z8 motherboard series. On
these boards, the memory slots are behind a GPIO-controlled I2C
multiplexer. Models with 6 or 12 memory slots have 2 segments behind
the multiplexer, while models with 18 memory slots have 3 such
segments.

On these boards, only the memory slots are behind the multiplexer,
so it is possible to keep the autodetection mechanism.

The code is generic enough so it could work on other boards as long as
the multiplexer is controlled by GPIO pins. For other forms of
multiplexing (for example using an I2C device) additional code will be
needed.

Thanks to Asus for providing a board to develop and test this feature,
as well as all the technical information required.

At the moment, the GPIO driver must be loaded before the i2c-i801
driver, but I hope to solve this soon, using deferred probing on
the i2c-mux-gpio side.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The SMBus controller in the VIA VX900 appears to be compatible with
the VIA VX855, so just add the device ID.

This closes kernel bug #43096.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Remove the global dependency of the I2C subsystem on HAS_IOMEM and
move the dependency to the i2c/busses submenu, with an exception for
i2c-stub.

The generic I2C part does not need to have HAS_IOMEM set and thus now
becomes available in UML, so the I2C subsystem can now be used, e.g.
by the i2c-stub driver, for development of I2C device drivers.

[JD: Some adjustments.]

[Heiko Carstens: Keep I2C disabled on S390.]
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This driver has the following properties compared to the old driver:
1. Support for multiple interfaces.
2. Interrupt driven I/O as opposed to polling/busy waiting.
3. Support for _one_ repeated start (Sr) condition, which is enough
   for most real-world applications including all SMBus transfer types.
   (The hardware does not support issuing arbitrary Sr conditions on the
    bus.)

testing: SoC: at91sam9g45
	 - BQ20Z80 battery SMBus client.
	 - on a 2.6.38 kernel with several i2c clients (temp-sensor,
	   audio-codec, touchscreen-controller, w1-bridge, io-expanders)
Signed-off-by: NNikolaus Voss <n.voss@weinmann.de>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NHubert Feurstein <h.feurstein@gmail.com>
Tested-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: NNicolas Ferre <nicolas.ferre@atmel.com>

[wsa: squashed with the following patches from Ludovic to have some flaws
fixed:
        i2c: at91: use managed resources
        i2c: at91: add warning about transmission issues for some devices
        i2c: at91: use an id table for SoC dependent parameters
]
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>