Convert many printk calls to DRM_DEBUG calls to reduce kernel log noise
for normal activities. Switch other printk calls to DRM_ERROR or DRM_INFO.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

We are seeing compilation failures on i386 in some environments due
to an undefined reference as below:

    ERROR: "__udivdi3" [drivers/gpu/drm/i915/i915.ko] undefined!

This is generated due to a raw 64 bit divide in the i915 driver.  Fix up
this raw divide.
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Currently we implemented basic sdvo lvds function,
But except for sdvo lvds fixed mode, we can not switch
to other modes, otherwise display get black. The patch
handle three operations to enable sdvo lvds. At first
duplicate sdvo fixed mode for adjustment, then according
to fixed mode line valid all modes, at last adjust input
mode to fit our requirement.

Acked by Li Peng <peng.li@linux.intel.com>
Signed-off-by: NMa Ling <ling.ma@intel.com>
Reviewed-by: NIan Romanick <idr@freedesktop.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

All 8xx class chips have the 66/48 split, not just 855.
Signed-off-by: NMa Ling <ling.ma@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

This patch from jbarnes and myself adds FIFO watermark control to the
driver.  This is needed for both power saving features on new platforms
with the so-called "big FIFO" and for controlling FIFO allocation
between pipes in multi-head configurations.

It's also necessary infrastructure to support things like framebuffer
compression and configuration supportability checks (i.e. checking a
configuration against available bandwidth).
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This patch enables error detection by enabling several types of error
interrupts.  When an error interrupt is received, the interrupt
handler captures the error state; hopefully resulting in an accurate
set of error data (error type, active head pointer, etc.).  The new
record is then available from sysfs.  The current code will also dump
the error state to the system log.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

* 'kmemleak' of git://linux-arm.org/linux-2.6:
  kmemleak: Inform kmemleak about pid_hash
  kmemleak: Do not warn if an unknown object is freed
  kmemleak: Do not report new leaked objects if the scanning was stopped
  kmemleak: Slightly change the policy on newly allocated objects
  kmemleak: Do not trigger a scan when reading the debug/kmemleak file
  kmemleak: Simplify the reports logged by the scanning thread
  kmemleak: Enable task stacks scanning by default
  kmemleak: Allow the early log buffer to be configurable.

* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
  dm table: fix blk_stack_limits arg to use bytes not sectors
  dm exception store: really fix type lookup

Merge branch 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (47 commits)
  perf report: Add --symbols parameter
  perf report: Add --comms parameter
  perf report: Add --dsos parameter
  perf_counter tools: Adjust only prelinked symbol's addresses
  perf_counter: Provide a way to enable counters on exec
  perf_counter tools: Reduce perf stat measurement overhead/skew
  perf stat: Use percentages for scaling output
  perf_counter, x86: Update x86_pmu after WARN()
  perf stat: Micro-optimize the code: memcpy is only required if no event is selected and !null_run
  perf stat: Improve output
  perf stat: Fix multi-run stats
  perf stat: Add -n/--null option to run without counters
  perf_counter tools: Remove dead code
  perf_counter: Complete counter swap
  perf report: Print sorted callchains per histogram entries
  perf_counter tools: Prepare a small callchain framework
  perf record: Fix unhandled io return value
  perf_counter tools: Add alias for 'l1d' and 'l1i'
  perf-report: Add bare minimum PERF_EVENT_READ parsing
  perf-report: Add modes for inherited stats and no-samples
  ...

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  Add Fenghua Yu as temporary co-maintainer for ia64
  [IA64] address compiler warnings perfmon.c/salinfo.c
  [IA64] Remove unnecessary semicolons
  [IA64] sprintf should not be used with same source & destination address

Wire up new syscalls rt_tgsigqueueinfo and perf_counter_open.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Wire up new syscalls rt_tgsigqueueinfo and perf_counter_open.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Maximum file size for hostfs mounts defaults to 2GB, so bigger files cannot be
read/written through hostfs. This patch initializes the maximum file size to
MAX_LFS_SIZE.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13531Signed-off-by: NWolfgang Illmeyer <wolfgang@illmeyer.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A crappy macro prevents us unlocking on a fail path.

Expand the macro and unlock appropriatelly.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make sure we do not actually request the RTC IRQ until the device driver
is fully ready to handle and process any interrupt.  This way a spurious
interrupt won't crash the system (which may happen if the bootloader was
poking the RTC right before booting Linux).
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Block writes require 64 byte alignment.  Since block writes could be used
with SGRAM or WRAM also refine the memory type detection to check for
either type before deciding to use the 64 byte alignment.
Signed-off-by: NVille Syrjala <syrjala@sci.fi>
Tested-by: NMikulas Patocka <mpatocka@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Apparently HP OmniBook 500's BIOS doesn't like the way atyfb reprograms
the hardware. The BIOS will simply hang after a reboot. Fix the problem
by restoring the hardware to it's original state on reboot.
Signed-off-by: NVille Syrjala <syrjala@sci.fi>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

IRQ handling is wrong for any GPIO >= PL061_GPIO_NR.

Fix this by implementing and using a proper .to_irq method.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Note that IRQ has not been initialized when kmalloc() fails.

Also, use DECLARE_BITMAP() to make the code clearer.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Nathan reported that

| commit 73d60b7f
| Author: Yinghai Lu <yinghai@kernel.org>
| Date:   Tue Jun 16 15:33:00 2009 -0700
|
|    page-allocator: clear N_HIGH_MEMORY map before we set it again
|
|    SRAT tables may contains nodes of very small size.  The arch code may
|    decide to not activate such a node.  However, currently the early boot
|    code sets N_HIGH_MEMORY for such nodes.  These nodes therefore seem to be
|    active although these nodes have no present pages.
|
|    For 64bit N_HIGH_MEMORY == N_NORMAL_MEMORY, so that works for 64 bit too

unintentionally and incorrectly clears the cpuset.mems cgroup attribute on
an i386 kvm guest, meaning that cpuset.mems can not be used.

Fix this by only clearing node_states[N_NORMAL_MEMORY] for 64bit only.
and need to do save/restore for that in find_zone_movable_pfn
Reported-by: NNathan Lynch <ntl@pobox.com>
Tested-by: NNathan Lynch <ntl@pobox.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>,
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

By writing a tasks's pid to the file, a process adds that task to that
cgroup/cpuset.  But to add a cpu/mem to a cpuset, the new list of cpus
should be written to the cpuset.mems file which would replace the old list
of cpus.  Make this clearer in the documentation.
Signed-off-by: NNikanth Karthikesan <knikanth@suse.de>
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Acked-by: NPaul Menage <menage@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

balance_dirty_pages can overreact and move all of the dirty pages to
writeback unnecessarily.

balance_dirty_pages makes its decision to throttle based on the number of
dirty plus writeback pages that are over the calculated limit,so it will
continue to move pages even when there are plenty of pages in writeback
and less than the threshold still dirty.

This allows it to overshoot its limits and move all the dirty pages to
writeback while waiting for the drives to catch up and empty the writeback
list.

A simple fio test easily demonstrates this problem.

fio --name=f1 --directory=/disk1 --size=2G -rw=write --name=f2 --directory=/disk2 --size=1G --rw=write --startdelay=10

This is the simplest fix I could find, but I'm not entirely sure that it
alone will be enough for all cases.  But it certainly is an improvement on
my desktop machine writing to 2 disks.

Do we need something more for machines with large arrays where
bdi_threshold * number_of_drives is greater than the dirty_ratio ?
Signed-off-by: NRichard Kennedy <richard@rsk.demon.co.uk>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The file opened in acct_on and freshly stored in the ns->bacct struct can
be closed in acct_file_reopen by a concurrent call after we release
acct_lock and before we call mntput(file->f_path.mnt).

Record file->f_path.mnt in a local variable and use this variable only.
Signed-off-by: NRenaud Lottiaux <renaud.lottiaux@kerlabs.com>
Signed-off-by: NLouis Rilling <louis.rilling@kerlabs.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Ion's cs.columbia.edu email address no longer works.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NIon Badulescu <ionut@badula.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When the 32-bit signed quantities get assigned to the u64 resource_size_t,
they are incorrectly sign-extended.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13253
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=9905Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Reported-by: NLeann Ogasawara <leann@ubuntu.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Reported-by: <pablomme@googlemail.com>
Tested-by: <pablomme@googlemail.com>
Cc: <stable@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Bugfix to spi_bitbang infrastructure: make sure to always set transfer
parameters on the first pass through the message's per-transfer loop.
This can matter with drivers that replace the per-word or per-buffer
transfer primitives, on busses with multiple SPI devices.

Previously, this could have started messages using the settings left after
previous messages.  The problem was observed when a high speed chip
(m25p80 type flash) was running very slowly because a low speed device
(avr8 microcontroller) had previously used the bus.  Similar faults could
have driven the low speed device too fast, or used an unexpected word
size.
Acked-by: NSteven A. Falco <sfalco@harris.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a mutex to avoid a circular locking problem between the mm layer
semaphore and fbdev ioctl mutex through the fb_mmap() call.

Also, add mutex to all places where smem_start and smem_len fields change
so the mutex inside the fb_mmap() is actually used.  Changing of these
fields before calling the framebuffer_register() are not mutexed.

This is 2.6.31 material.  It removes one lockdep (fb_mmap() and
register_framebuffer()) but there is still another one (fb_release() and
register_framebuffer()).  It also cleans up handling of the smem_start and
smem_len fields used by mutexed section of the fb_mmap().
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a new spi_master.flags word listing constraints relevant to that
controller.  Define the first constraint bit: a half duplex restriction.
Include that constraint in the OMAP1 MicroWire controller driver.

Have the mmc_spi host be the first customer of this flag.  Its coding
relies heavily on full duplex transfers, so it must fail when the
underlying controller driver won't perform them.

(The spi_write_then_read routine could use it too: use the
temporarily-withdrawn full-duplex speedup unless this flag is set, in
which case the existing code applies.  Similarly, any spi_master
implementing only SPI_3WIRE should set the flag.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add two new spi_device.mode bits to accomodate more protocol options, and
pass them through to usermode drivers:

 * SPI_NO_CS ... a second 3-wire variant, where the chipselect
   line is removed instead of a data line; transfers are still
   full duplex.

   This obviously has STRONG protocol implications since the
   chipselect transitions can't be used to synchronize state
   transitions with the SPI master.

 * SPI_READY ... defines open drain signal that's pulled low
   to pause the clock.  This defines a 5-wire variant (normal
   4-wire SPI plus READY) and two 4-wire variants (READY plus
   each of the 3-wire flavors).

   Such hardware flow control can be a big win.  There are ADC
   converters and flash chips that expose READY signals, but not
   many host controllers support it today.

The spi_bitbang code should be changed to use SPI_NO_CS instead of its
current nonportable hack.  That's a mode most hardware can easily support
(unlike SPI_READY).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: "Paulraj, Sandeep" <s-paulraj@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

show_pools() walks the page_list of a pool w/o protection against the list
modifications in alloc/free.  Take pool->lock to avoid stomping into
nirvana.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ext2_iget() returns -ESTALE if invoked on a deleted inode, in order to
report errors to NFS properly.  However, in ext[234]_lookup(), this
-ESTALE can be propagated to userspace if the filesystem is corrupted such
that a directory entry references a deleted inode.  This leads to a
misleading error message - "Stale NFS file handle" - and confusion on the
part of the admin.

The bug can be easily reproduced by creating a new filesystem, making a
link to an unused inode using debugfs, then mounting and attempting to ls
-l said link.

This patch thus changes ext2_lookup to return -EIO if it receives -ESTALE
from ext2_iget(), as ext2 does for other filesystem metadata corruption;
and also invokes the appropriate ext*_error functions when this case is
detected.
Signed-off-by: NBryan Donlan <bdonlan@gmail.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With ELF, at generating coredump, some more headers other than used
vmas are added.

When max_map_count == 65536, a core generated by following kinds of
code can be unreadable because the number of ELF's program header is
written in 16bit in Ehdr (please see elf.h) and the number overflows.

==
	... = mmap(); (munmap, mprotect, etc...)
	if (failed)
		abort();
==

This can happen in mmap/munmap/mprotect/etc...which calls split_vma().

I think 65536 is not safe as _default_ and reduce it to 65530 is good
for avoiding unexpected corrupted core.

Anyway, max_map_count can be enlarged by sysctl if a user is brave..
Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Jakub Jelinek <jakub@redhat.com>
Acked-by: NRoland McGrath <roland@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since some new MPC85xx SOCs support DDR3 memory now, so add DDR3 memory
type for MPC85xx EDAC.
Signed-off-by: NYang Shi <yang.shi@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the PCI-Express NetMos 9901 Multi-IO card.

0001:06:00.0 Serial controller [0700]: NetMos Technology Device [9710:9901] (prog-if 02 [16550])
        Subsystem: Device [a000:1000]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 65
        Region 0: I/O ports at 0030 [size=8]
        Region 1: Memory at 80105000 (32-bit, non-prefetchable) [size=4K]
        Region 4: Memory at 80104000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
        Kernel driver in use: serial
        Kernel modules: 8250_pci

0001:06:00.1 Serial controller [0700]: NetMos Technology Device [9710:9901] (prog-if 02 [16550])
        Subsystem: Device [a000:1000]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin B routed to IRQ 65
        Region 0: I/O ports at 0020 [size=8]
        Region 1: Memory at 80103000 (32-bit, non-prefetchable) [size=4K]
        Region 4: Memory at 80102000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
        Kernel driver in use: serial
        Kernel modules: 8250_pci

0001:06:00.2 Parallel controller [0701]: NetMos Technology Device [9710:9901] (prog-if 03 [IEEE1284])
        Subsystem: Device [a000:2000]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin C routed to IRQ 65
        Region 0: I/O ports at 0010 [size=8]
        Region 1: I/O ports at <unassigned>
        Region 2: Memory at 80101000 (32-bit, non-prefetchable) [size=4K]
        Region 4: Memory at 80100000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: <access denied>
        Kernel driver in use: parport_pc
        Kernel modules: parport_pc

[   16.760181] PCI parallel port detected: 416c:0100, I/O at 0x812010(0x0), IRQ 65
[   16.760225] parport0: PC-style at 0x812010, irq 65 [PCSPP,TRISTATE,EPP]
[   16.851842] serial 0001:06:00.0: enabling device (0004 -> 0007)
[   16.883776] 0001:06:00.0: ttyS0 at I/O 0x812030 (irq = 65) is a ST16650V2
[   16.893832] serial 0001:06:00.1: enabling device (0004 -> 0007)
[   16.926537] 0001:06:00.1: ttyS1 at I/O 0x812020 (irq = 65) is a ST16650V2
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commonly available versions of cp and tar don't work well with special
files created using seq_file.  Mention this problem in the gcov
documentation and update the helper script example to work around these
problems.
Signed-off-by: NPeter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

alpha percpu access requires custom SHIFT_PERCPU_PTR() definition for
modules to work around addressing range limitation.  This is done via
generating inline assembly using C preprocessing which forces the
assembler to generate external reference.  This happens behind the
compiler's back and makes the compiler think that static percpu variables
in modules are unused.

This used to be worked around by using __unused attribute for percpu
variables which prevent the compiler from omitting the variable; however,
recent declare/definition attribute unification change broke this as
__used can't be used for declaration.  Also, in the process,
PER_CPU_ATTRIBUTES definition in alpha percpu.h got broken.

This patch adds PER_CPU_DEF_ATTRIBUTES which is only used for definitions
and make alpha use it to add __used for percpu variables in modules.  This
also fixes the PER_CPU_ATTRIBUTES double definition bug.
Signed-off-by: NTejun Heo <tj@kernel.org>
Tested-by: Nmaximilian attems <max@stro.at>
Acked-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When building with a 4.1.x compiler on powerpc64 (at least) we get this
error:

drivers/video/logo/logo_linux_mono.c:81: error: logo_linux_mono causes a section type conflict

This was introduced by commit ae52bb23
("fbdev: move logo externs to header file").  This is a partial revert of
that commit sufficient to not hit the compiler bug.

Also convert _clut arrays from __initconst to __initdata.

Sam said:

  Al analysed this some time ago.  When we say something is const then
  _sometimes_ gcc annotate the section as const(?) - sometimes not.  So if
  we have two variables/functions annotated __*const and gcc decides to
  annotate the section const only in one case we get a section type
  conflict.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As per Ranganathan's request.
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: Arvind R. <arvind@jetztechnologies.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The ctors section for each object file is eight byte aligned (on 64 bit).
However the __ctors_start symbol starts at an arbitrary address dependent
on the size of the previous sections.

Therefore the linker may add some zeroes after __ctors_start to make sure
the ctors contents are properly aligned.  However the extra zeroes at the
beginning aren't expected by the code.  When walking the functions
pointers contained in there and extra zeroes are added this may result in
random jumps.  So make sure that the __ctors_start symbol is always
aligned as well.

Fixes this crash on an allyesconfig on s390:

[    0.582482] Kernel BUG at 0000000000000012 [verbose debug info unavailable]
[    0.582489] illegal operation: 0001 [#1] SMP DEBUG_PAGEALLOC
[    0.582496] Modules linked in:
[    0.582501] CPU: 0 Tainted: G        W  2.6.31-rc1-dirty #273
[    0.582506] Process swapper (pid: 1, task: 000000003f218000, ksp: 000000003f2238e8)
[    0.582510] Krnl PSW : 0704200180000000 0000000000000012 (0x12)
[    0.582518]            R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:0 CC:2 PM:0 EA:3
[    0.582524] Krnl GPRS: 0000000000036727 0000000000000010 0000000000000001 0000000000000001
[    0.582529]            00000000001dfefa 0000000000000000 0000000000000000 0000000000000040
[    0.582534]            0000000001fff0f0 0000000001790628 0000000002296048 0000000002296048
[    0.582540]            00000000020c438e 0000000001786000 0000000002014a66 000000003f223e60
[    0.582553] Krnl Code:>0000000000000012: 0000                unknown
[    0.582559]            0000000000000014: 0000                unknown
[    0.582564]            0000000000000016: 0000                unknown
[    0.582570]            0000000000000018: 0000                unknown
[    0.582575]            000000000000001a: 0000                unknown
[    0.582580]            000000000000001c: 0000                unknown
[    0.582585]            000000000000001e: 0000                unknown
[    0.582591]            0000000000000020: 0000                unknown
[    0.582596] Call Trace:
[    0.582599] ([<0000000002014a46>] kernel_init+0x622/0x7a0)
[    0.582607]  [<0000000000113e22>] kernel_thread_starter+0x6/0xc
[    0.582615]  [<0000000000113e1c>] kernel_thread_starter+0x0/0xc
[    0.582621] INFO: lockdep is turned off.
[    0.582624] Last Breaking-Event-Address:
[    0.582627]  [<0000000002014a64>] kernel_init+0x640/0x7a0

Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change the eventfd interface to de-couple the eventfd memory context, from
the file pointer instance.

Without such change, there is no clean way to racely free handle the
POLLHUP event sent when the last instance of the file* goes away.  Also,
now the internal eventfd APIs are using the eventfd context instead of the
file*.

This patch is required by KVM's IRQfd code, which is still under
development.
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Cc: Gregory Haskins <ghaskins@novell.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>