When logging to console is disabled from userspace using klogctl()
and later re-enabled, console_loglevel gets set to the default
log level instead to the previous value.

This means that if the kernel was booted with 'quiet', the boot is
suddenly no longer quiet after logging to console gets re-enabled.

Save the current console_loglevel when logging is disabled and
restore to that value. If the log level is set to a specific value
while disabled, this is interpreted as an implicit re-enabling of
the logging.

The problem that prompted this patch is described in:

    http://lkml.org/lkml/2009/6/28/234

There are two variations possible on the patch below:

 1) If klogctl(7) is called while logging is not disabled, then set level
    to default (partially preserving current functionality):
  	case 7:		/* Enable logging to console */
 -		console_loglevel = default_console_loglevel;
 +		if (saved_console_loglevel == -1)
 +			console_loglevel = default_console_loglevel;
 +		else {
 +			console_loglevel = saved_console_loglevel;
 +			saved_console_loglevel = -1;
 +		}

 2) If klogctl(8) is called while logging is disabled, then don't enable
    logging, but remember the requested value for when logging does get
    enabled again:
  	case 8:		/* Set level of messages printed to console */
 [...]
 - 		console_loglevel = len;
 +		if (saved_console_loglevel == -1)
 +			console_loglevel = len;
 +		else
 +			saved_console_loglevel = len;

Yet another option would be to ignore the request.
Signed-off-by: NFrans Pop <elendil@planet.nl>
Cc: cryptsetup@packages.debian.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <200907061331.49930.elendil@planet.nl>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Today, when a console is registered without CON_PRINTBUFFER,
end users never see the announcement of it being added, and
never know if they missed something, if the console is really
at the start or not, and just leads to general confusion.

This re-orders existing code, to make sure the console is
added, before the "console [%s%d] enabled" is printed out -
ensuring that this message is _always_ seen.

This has the desired/intended side effect of making sure that
"console enabled:" messages are printed on the bootconsole, and
the real console. This does cause the same line is printed
twice if the bootconsole and real console are the same device,
but if they are on different devices, the message is printed to
both consoles.

Signed-off-by : Robin Getz <rgetz@blackfin.uclinux.org>
Cc: "Andrew Morton" <akpm@linux-foundation.org>
Cc: "Linus Torvalds" <torvalds@linux-foundation.org>
LKML-Reference: <200907091308.37370.rgetz@blackfin.uclinux.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Today, register_console() assumes the following usage:

  - The first console to register with a flag set to CON_BOOT
    is the one and only bootconsole.

  - If another register_console() is called with an additional
    CON_BOOT, it is silently rejected.

  - As soon as a console without the CON_BOOT set calls
    registers the bootconsole is automatically unregistered.

  - Once there is a "real" console - register_console() will
    silently reject any consoles with it's CON_BOOT flag set.

In many systems (alpha, blackfin, microblaze, mips, powerpc,
sh, & x86), there are early_printk implementations, which use
the CON_BOOT which come out serial ports, vga, usb, & memory
buffers.

In many embedded systems, it would be nice to have two
bootconsoles - in case the primary fails, you always have
access to a backup memory buffer - but this requires at least
two CON_BOOT consoles...

This patch enables that functionality.

With the change applied, on boot you get (if you try to
re-enable a boot console after the "real" console has been
registered):

  root:/> dmesg | grep console
  bootconsole [early_shadow0] enabled
  bootconsole [early_BFuart0] enabled
  Kernel command line: root=/dev/mtdblock0 rw earlyprintk=serial,uart0,57600 console=ttyBF0,57600 nmi_debug=regs
  console handover:boot [early_BFuart0] boot [early_shadow0]  -> real [ttyBF0]
  Too late to register bootconsole early_shadow0

or:

  root:/> dmesg | grep console
  Kernel command line: root=/dev/mtdblock0 rw console=ttyBF0,57600
  console [ttyBF0] enabled
Signed-off-by: NRobin Getz <rgetz@blackfin.uclinux.org>
Cc: "Linus Torvalds" <torvalds@linux-foundation.org>
Cc: "Andrew Morton" <akpm@linux-foundation.org>
Cc: "Mike Frysinger" <vapier.adi@gmail.com>
Cc: "Paul Mundt" <lethal@linux-sh.org>
LKML-Reference: <200907012108.38030.rgetz@blackfin.uclinux.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

fix hang with HIGHMEM_64G and 32bit resource.  According to hpa and
Linus, use (resource_size_t)-1 to fend off big ranges.

Analyzed by hpa
Reported-and-tested-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

These macros had two bugs:
 - the type of the mask was not correctly expanded to the full size of
   the argument being expanded, resulting in possible loss of high bits
   when mixing types.
 - the alignment argument was evaluated twice, despite the macro looking
   like a fancy function (but it really does need to be a macro, since
   it works on arbitrary integer types)

Noticed by Peter Anvin, and with a fix that is a modification of his
suggestion (bug noticed by Yinghai Lu).

Cc: Peter Anvin <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add basic performance counter support to the FRV arch.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Implement atomic64_t and its ops for FRV.  Tested with the following patch:

	diff --git a/arch/frv/kernel/setup.c b/arch/frv/kernel/setup.c
	index 55e4fab..086d50d 100644
	--- a/arch/frv/kernel/setup.c
	+++ b/arch/frv/kernel/setup.c
	@@ -746,6 +746,52 @@ static void __init parse_cmdline_early(char *cmdline)

	 } /* end parse_cmdline_early() */

	+static atomic64_t xxx;
	+
	+static void test_atomic64(void)
	+{
	+	atomic64_set(&xxx, 0x12300000023LL);
	+
	+	mb();
	+	BUG_ON(atomic64_read(&xxx) != 0x12300000023LL);
	+	mb();
	+	if (atomic64_inc_return(&xxx) != 0x12300000024LL)
	+		BUG();
	+	mb();
	+	BUG_ON(atomic64_read(&xxx) != 0x12300000024LL);
	+	mb();
	+	if (atomic64_sub_return(0x36900000050LL, &xxx) != -0x2460000002cLL)
	+		BUG();
	+	mb();
	+	BUG_ON(atomic64_read(&xxx) != -0x2460000002cLL);
	+	mb();
	+	if (atomic64_dec_return(&xxx) != -0x2460000002dLL)
	+		BUG();
	+	mb();
	+	BUG_ON(atomic64_read(&xxx) != -0x2460000002dLL);
	+	mb();
	+	if (atomic64_add_return(0x36800000001LL, &xxx) != 0x121ffffffd4LL)
	+		BUG();
	+	mb();
	+	BUG_ON(atomic64_read(&xxx) != 0x121ffffffd4LL);
	+	mb();
	+	if (atomic64_cmpxchg(&xxx, 0x123456789abcdefLL, 0x121ffffffd4LL) != 0x121ffffffd4LL)
	+		BUG();
	+	mb();
	+	BUG_ON(atomic64_read(&xxx) != 0x121ffffffd4LL);
	+	mb();
	+	if (atomic64_cmpxchg(&xxx, 0x121ffffffd4LL, 0x123456789abcdefLL) != 0x121ffffffd4LL)
	+		BUG();
	+	mb();
	+	BUG_ON(atomic64_read(&xxx) != 0x123456789abcdefLL);
	+	mb();
	+	if (atomic64_xchg(&xxx, 0xabcdef123456789LL) != 0x123456789abcdefLL)
	+		BUG();
	+	mb();
	+	BUG_ON(atomic64_read(&xxx) != 0xabcdef123456789LL);
	+	mb();
	+}
	+
	 /*****************************************************************************/
	 /*
	  *
	@@ -845,6 +891,8 @@ void __init setup_arch(char **cmdline_p)
	 //	asm volatile("movgs %0,timerd" :: "r"(10000000));
	 //	__set_HSR(0, __get_HSR(0) | HSR0_ETMD);

	+	test_atomic64();
	+
	 } /* end setup_arch() */

	 #if 0

Note that this doesn't cover all the trivial wrappers, but does cover all the
substantial implementations.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: LCDC dcache flush for deferred io
  sh: Fix compiler error and include the definition of IS_ERR_VALUE
  sh: re-add LCDC fbdev support to the Migo-R defconfig
  sh: fix se7724 ceu names
  sh: ms7724se: Enable sh_eth in defconfig.
  arch/sh/boards/mach-se/7206/io.c: Remove unnecessary semicolons
  sh: ms7724se: Add sh_eth support
  nommu: provide follow_pfn().
  sh: Kill off unused DEBUG_BOOTMEM symbol.
  perf_counter tools: add cpu_relax()/rmb() definitions for sh.
  sh64: Hook up page fault events for software perf counters.
  sh: Hook up page fault events for software perf counters.
  sh: make set_perf_counter_pending() static inline.
  clocksource: sh_tmu: Make undefined TCOR behaviour less undefined.

Since writenotify on uncached vmas is unsupported in 2.6.31,
live with cached framebuffer memory in the deferred io
case for now and flush the dcache before forcing refresh.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Acked-by: NMagnus damm <damm@igel.co.jp>

When arch/sh/include/asm/syscall_32.h is included from a file that
doesn't also include linux/err.h the following error is produced,

In file included from /home/matt/src/kernels/sh-2.6/arch/sh/include/asm/syscall.h:5,
                 from kernel/trace/trace_syscalls.c:3:
/home/matt/src/kernels/sh-2.6/arch/sh/include/asm/syscall_32.h: In function 'syscall_get_error':
/home/matt/src/kernels/sh-2.6/arch/sh/include/asm/syscall_32.h:28: error: implicit declaration of function 'IS_ERR_VALUE'
make[2]: *** [kernel/trace/trace_syscalls.o] Error 1
make[1]: *** [kernel/trace] Error 2
make: *** [kernel] Error 2
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Somehow I managed to generate a diff that put these 2 lines
into the wrong function:  should have been in dump_struct()
instead of in dump_enum().
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.infradead.org/mtd-2.6:
  mtd: nand: fix build failure and incorrect return from omap_wait()
  mtd: Use BLOCK_NIL consistently in NFTL/INFTL
  mtd: m25p80 timeout too short for worst-case m25p16 devices
  mtd: atmel_nand: Fix typo s/parititions/partitions/
  mtd: cmdlineparts: Use 64-bit format when printing a debug message.
  mtd: maps: Remove BUS_ID_SIZE from integrator_flash
  jffs2: fix another potential leak on error path in scan.c

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: invalidation reverse calls
  fuse: allow umask processing in userspace
  fuse: fix bad return value in fuse_file_poll()
  fuse: fix return value of fuse_dev_write()

This fixes kernel.org bug #13584. The IOVA code attempted to optimise
the insertion of new ranges into the rbtree, with the unfortunate result
that some ranges just didn't get inserted into the tree at all. Then
those ranges would be handed out more than once, and things kind of go
downhill from there.

Introduced after 2.6.25 by ddf02886
("PCI: iova RB tree setup tweak").
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Cc: mark gross <mgross@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We can run a 32-bit kernel on boxes with an IOMMU, so we need
pci_unmap_addr() etc. to work -- without it, drivers will leak mappings.

To be honest, this whole thing looks like it's more pain than it's
worth; I'm half inclined to remove the no-op #else case altogether.

But this is the minimal fix, which just does the right thing if
CONFIG_DMAR is set.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org  [ for 2.6.30 ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Check before use it.
Signed-off-by: NWANG Cong <amwang@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Acked-by: NRoland McGrath <roland@redhat.com>
Acked-by: NJames Morris <jmorris@namei.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  cfq-iosched: remove redundant check for NULL cfqq in cfq_set_request()
  blocK: Restore barrier support for md and probably other virtual devices.
  block: get rid of queue-private command filter
  block: Create bip slabs with embedded integrity vectors
  cfq-iosched: get rid of the need for __GFP_NOFAIL in cfq_find_alloc_queue()
  cfq-iosched: move cfqq initialization out of cfq_find_alloc_queue()
  Trivial typo fixes in Documentation/block/data-integrity.txt.

* 'for-linus' of git://neil.brown.name/md:
  md: use interruptible wait when duration is controlled by userspace.
  md/raid5: suspend shouldn't affect read requests.
  md: tidy up error paths in md_alloc
  md: fix error path when duplicate name is found on md device creation.
  md: avoid dereferencing NULL pointer when accessing suspend_* sysfs attributes.
  md: Use new topology calls to indicate alignment and I/O sizes

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (31 commits)
  Revert "ipv4: arp announce, arp_proxy and windows ip conflict verification"
  igb: return PCI_ERS_RESULT_DISCONNECT on permanent error
  e1000e: io_error_detected callback should return PCI_ERS_RESULT_DISCONNECT
  e1000: return PCI_ERS_RESULT_DISCONNECT on permanent error
  e1000: fix unmap bug
  igb: fix unmap length bug
  ixgbe: fix unmap length bug
  ixgbe: Fix link capabilities during adapter resets
  ixgbe: Fix device capabilities of 82599 single speed fiber NICs.
  ixgbe: Fix SFP log messages
  usbnet: Remove private stats structure
  usbnet: Use netdev stats structure
  smsc95xx: Use netdev stats structure
  rndis_host: Use netdev stats structure
  net1080: Use netdev stats structure
  dm9601: Use netdev stats structure
  cdc_eem: Use netdev stats structure
  ipv4: Fix fib_trie rebalancing, part 3
  bnx2x: Fix the behavior of ethtool when ONBOOT=no
  sctp: xmit sctp packet always return no route error
  ...

One of the kmemleak changes caused the following
scheduling-while-holding-the-tasklist-lock regression on x86:

BUG: sleeping function called from invalid context at mm/kmemleak.c:795
in_atomic(): 1, irqs_disabled(): 0, pid: 1737, name: kmemleak
2 locks held by kmemleak/1737:
 #0:  (scan_mutex){......}, at: [<c10c4376>] kmemleak_scan_thread+0x45/0x86
 #1:  (tasklist_lock){......}, at: [<c10c3bb4>] kmemleak_scan+0x1a9/0x39c
Pid: 1737, comm: kmemleak Not tainted 2.6.31-rc1-tip #59266
Call Trace:
 [<c105ac0f>] ? __debug_show_held_locks+0x1e/0x20
 [<c102e490>] __might_sleep+0x10a/0x111
 [<c10c38d5>] scan_yield+0x17/0x3b
 [<c10c3970>] scan_block+0x39/0xd4
 [<c10c3bc6>] kmemleak_scan+0x1bb/0x39c
 [<c10c4331>] ? kmemleak_scan_thread+0x0/0x86
 [<c10c437b>] kmemleak_scan_thread+0x4a/0x86
 [<c104d73e>] kthread+0x6e/0x73
 [<c104d6d0>] ? kthread+0x0/0x73
 [<c100959f>] kernel_thread_helper+0x7/0x10
kmemleak: 834 new suspected memory leaks (see /sys/kernel/debug/kmemleak)

The bit causing it is highly dubious:

static void scan_yield(void)
{
        might_sleep();

        if (time_is_before_eq_jiffies(next_scan_yield)) {
                schedule();
                next_scan_yield = jiffies + jiffies_scan_yield;
        }
}

It called deep inside the codepath and in a conditional way,
and that is what crapped up when one of the new scan_block()
uses grew a tasklist_lock dependency.

This minimal patch removes that yielding stuff and adds the
proper cond_resched().

The background scanning thread could probably also be reniced
to +10.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NPekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With the changes for falling back to an oom_cfqq, we never fail
to find/allocate a queue in cfq_get_queue(). So remove the check.
Signed-off-by: NShan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

The next_ordered flag is only meaningful for devices that use __make_request.
So move the test against next_ordered out of generic code and in to
__make_request

Since this test was added, barriers have not worked on md or any
devices that don't use __make_request and so don't bother to set
next_ordered.  (dm explicitly sets something other than
QUEUE_ORDERED_NONE since
  commit 99360b4c
but notes in the comments that it is otherwise meaningless).

Cc: Ken Milmore <ken.milmore@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

The initial patches to support this through sysfs export were broken
and have been if 0'ed out in any release. So lets just kill the code
and reclaim some space in struct request_queue, if anyone would later
like to fixup the sysfs bits, the git history can easily restore
the removed bits.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This patch restores stacking ability to the block layer integrity
infrastructure by creating a set of dedicated bip slabs.  Each bip slab
has an embedded bio_vec array at the end.  This cuts down on memory
allocations and also simplifies the code compared to the original bvec
version.  Only the largest bip slab is backed by a mempool.  The pool is
contained in the bio_set so stacking drivers can ensure forward
progress.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJens Axboe <axboe@carl.(none)>

Setup an emergency fallback cfqq that we allocate at IO scheduler init
time. If the slab allocation fails in cfq_find_alloc_queue(), we'll just
punt IO to that cfqq instead. This ensures that cfq_find_alloc_queue()
never fails without having to ensure free memory.

On cfqq lookup, always try to allocate a new cfqq if the given cfq io
context has the oom_cfqq assigned. This ensures that we only temporarily
punt to this shared queue.
Reviewed-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

We're going to be needing that init code outside of that function
to get rid of the __GFP_NOFAIL in cfqq allocation.
Reviewed-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Signed-off-by: NAndre Noll <maan@systemlinux.org>
Acked-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Re-add LCDC fbdev support to the Migo-R defconfig.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use "ceu0" and "ceu1" as CEU names instead of "ceu".
This fixes "memchunk" kernel command line selection
on the solution engine 7724 board.

With this patch applied use "memchunk.ceu0=1m" or
"memchunk.ceu1=1m" on kernel command line to override
physically memory size to one meg for CEU0 or CEU1.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

User space can set various limits on an md array so that resync waits
when it gets to a certain point, or so that I/O is blocked for a short
while.
When md is waiting against one of these limit, it should use an
interruptible wait so as not to add to the load average, and so are
not to trigger a warning if the wait goes on for too long.
Signed-off-by: NNeilBrown <neilb@suse.de>

md allows write to regions on an array to be suspended temporarily.
This allows user-space to participate is aspects of reshape.
In particular, data can be copied with not risk of a race.
We should not be blocking read requests though, so don't.

Cc: stable@kernel.org
Signed-off-by: NNeilBrown <neilb@suse.de>

This reverts commit 73ce7b01.

After discovering that we don't listen to gratuitious arps in 2.6.30
I tracked the failure down to this commit.

The patch makes absolutely no sense.  RFC2131 RFC3927 and RFC5227.
are all in agreement that an arp request with sip == 0 should be used
for the probe (to prevent learning) and an arp request with sip == tip
should be used for the gratitous announcement that people can learn
from.

It appears the author of the broken patch got those two cases confused
and modified the code to drop all gratuitous arp traffic.  Ouch!

Cc: stable@kernel.org
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PCI drivers that implement the io_error_detected callback should return
PCI_ERS_RESULT_DISCONNECT if the state passed in is
pci_channel_io_perm_failure.  This patch fixes the issue for igb.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

on permanent failure

PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure.  This state is not
checked in many of the network drivers.

This patch fixes the omission in the e1000e driver.
Signed-off-by: NMike Mason <mmlnx@us.ibm.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure.  This state is
not checked in many of the network drivers.

The patch fixes the omission in the e1000 driver.

Based on Mike Mason's similar patch for e1000e.
Signed-off-by: NAndre Detsch <adetsch@br.ibm.com>
CC: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

as reported by kerneloops.org

[  121.781161] ------------[ cut here ]------------
[  121.781171] WARNING: at lib/dma-debug.c:793 check_unmap+0x14e/0x577()
[  121.781173] Hardware name: S5520HC
[  121.781177] e1000 0000:0a:00.0: DMA-API: device driver tries to free DMA
memory it has not allocated [device address=0x00000001d688b0fa] [size=1522
bytes]
[  121.781180] Modules linked in: e1000 mdio  dca [last unloaded: ixgbe]
[  121.781187] Pid: 4793, comm: bash Tainted: P 2.6.30-master-06161113 #3
[  121.781190] Call Trace:
[  121.781195]  [<ffffffff8123056f>] ? check_unmap+0x14e/0x577
[  121.781201]  [<ffffffff81057a19>] warn_slowpath_common+0x77/0x8f
[  121.781205]  [<ffffffff81057ae1>] warn_slowpath_fmt+0x9f/0xa1
[  121.781212]  [<ffffffff81477ce2>] ? _spin_lock_irqsave+0x3f/0x49
[  121.781216]  [<ffffffff8122fa97>] ? get_hash_bucket+0x28/0x33
[  121.781220]  [<ffffffff8123056f>] check_unmap+0x14e/0x577
[  121.781225]  [<ffffffff810e4f48>] ? check_bytes_and_report+0x38/0xcb
[  121.781230]  [<ffffffff81230bbf>] debug_dma_unmap_page+0x80/0x92
[  121.781234]  [<ffffffff8122e549>] ? unmap_single+0x1a/0x4e
[  121.781239]  [<ffffffff813901e1>] ? __kfree_skb+0x74/0x78
[  121.781250]  [<ffffffffa00662ef>] pci_unmap_single+0x64/0x6d [e1000]
[  121.781259]  [<ffffffffa0066344>] e1000_clean_rx_ring+0x4c/0xbf [e1000]
[  121.781268]  [<ffffffffa00663df>] e1000_clean_all_rx_rings+0x28/0x36 [e1000]
[  121.781277]  [<ffffffffa0067464>] e1000_down+0x138/0x141 [e1000]
[  121.781286]  [<ffffffffa00681c2>] __e1000_shutdown+0x6b/0x198 [e1000]
[  121.781296]  [<ffffffffa0068405>] e1000_suspend+0x17/0x50 [e1000]
[  121.781301]  [<ffffffff81237665>] pci_legacy_suspend+0x3b/0xbe
[  121.781305]  [<ffffffff81237bc6>] pci_pm_suspend+0x3e/0xf1
[  121.781310]  [<ffffffff812eaf1c>] pm_op+0x57/0xde
[  121.781314]  [<ffffffff812eb444>] dpm_suspend_start+0x31e/0x470
[  121.781319]  [<ffffffff810877da>] suspend_devices_and_enter+0x3e/0x1a2
[  121.781323]  [<ffffffff81087a0f>] enter_state+0xd1/0x127
[  121.781327]  [<ffffffff8108717a>] state_store+0xa7/0xc9
[  121.781332]  [<ffffffff81221843>] kobj_attr_store+0x17/0x19
[  121.781336]  [<ffffffff8113c01e>] sysfs_write_file+0xe5/0x121
[  121.781341]  [<ffffffff810ed165>] vfs_write+0xab/0x105
[  121.781344]  [<ffffffff810ed279>] sys_write+0x47/0x6d
[  121.781349]  [<ffffffff81027aab>] system_call_fastpath+0x16/0x1b
[  121.781352] ---[ end trace 97bacaaac2ed7786 ]---

Fix is to correctly zero out internal ->dma value when unmapping
and make sure never to unmap unless there specifically was a mapping done.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

driver was mixing NET_IP_ALIGN count bytes in map/unmap calls
unevenly. Only map the bytes that the hardware might dma into

also fix unmap related bug where ->dma was not being cleared
after unmap
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses three WARN_ON statements from DMA-API debug code

ixgbe is mapping more than it unmaps, reduce the length of the map call and
remove the "used once" local variable.

found by Joerg Roedel <joerg.roedel@amd.com> in 2.6.30, so is a candidate
for -stable.

in addition, fix missing ->dma = 0 after unmap to prevent double free with
pci_unmap_single

and lastly, don't unmap (half) pages that aren't mapped.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adapter link advertisement capabilities were not persistent during
adapter resets. While configuring multispeed fiber link check for
phy autoneg_advertised settings before overwriting with default
link capabilities
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

82599 single speed fiber modules only support 10G/Full. Return
proper device capabilities while querrying the adapter and error
while changing device advertisement/speed/duplex capabilities.
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>