It should have been removed by commit "mwifiex: use cfg80211 dynamic
scan..." (7c6fa2a8..) after adding code to avoid an extra scan
during association because scan entries are valid for 15 seconds in
cfg80211 stack.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's just a duplicate of ipw2100_bg_rates[].
Signed-off-by: NStanislav Yakovlev <stas.yakovlev@gmail.com>
Reviewed-by: NJulian Calaby <julian.calaby@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I am running Debian testing kernel 3.1.0-1-amd64, using a 079b:0062 Sagem
XG-76NA 802.11bg stick.

Upon zd1211rw interface
bringup (ifconfig wlan0 up) I get the following timeout:

[  950.330573] zd1211rw 1-3:1.0: phy2
[  955.108510] zd1211rw 1-3:1.0: firmware version 4725
[  955.148532] zd1211rw 1-3:1.0: zd1211b chip 079b:0062 v4810 high 00-19-70
AL2230_RF pa0 g--NS
[snip]
[  955.204072] zd1211rw 1-3:1.0: error ioread32(CR_REG1): -110

A second ifconfig wlan0 up brings the interface up without problems.

After a bit more debugging, the call trace is the following:

[10241.028130] zd1211rw 1-3:1.0: zd_chip_lock_phy_regs: error
ioread32(CR_REG1): -110
[10241.028140] zd1211rw 1-3:1.0: zd_switch_radio_on: failed to lock PHY regs
[10241.028148] zd1211rw 1-3:1.0: zd_op_start: failed to set radio on

Adding a 10 milliseconds delay between the call to set_mc_hash() and
zd_chip_switch_radio_on() allows successful interface bringups in all
cases and matches what the vendor driver did.
Acked-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a fixup for my:
iwlwifi: kill iwl_bus.h

Please fold them into one patch for upstream
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Update the pci subsystem id and product name for 6005 series devices
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Add new sku to 6x35 series
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

We can use forward declaration for the relevant struct since they
aren't dereferenced in the header file.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Also add a might_sleep to enforce the context requirements.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

It is op_mode related
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

It is op_mode related
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

No one needs it any more
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

This is temporary, but at least we can now throw the bus away
and move the iwl_pci_{probe,remove} functions.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

They don't need to be in iwl-dev.h
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The transport should not dereference the iwl_priv pointer. Remove a
few of those.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Export it as "nic_error" notification, the error handling will be in
the op_mode.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Export it as "hw_rf_kill" notification.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Export them as "queue_full" and "queue_not_full" notification.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

This is the op_mode's Rx handler.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

This handler allows the transport layer to free an skb from the
op_mode. This can happen when the driver is stopped while Tx
packets are pending in the transport layer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Sparse prefers __aligned(sizeof(void *));
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Define the op_mode as an interface with its ops. All the functions
of the op_mode are "private", but its ops is made public in
iwl-op-mode.h.
The drv object starts the op_mode by using the start function in the
public ops.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

iwl_remove stops the wifi flows, so rename.
Moreover, we can possibly stop the wifi flows even if the driver
is statically compiled in the kernel, so remove the __devexit pragma.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Move that code to the iwl-drv.c
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Fetch the fw and spawn the op_mode. The op_mode that we need
to fetch is determined from the fw file.
Since the fw is fetched very early in the init flow, we can
determine what op_mode to spawn.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The uCode flags modification is op_mode dependent
since the P2P config is an op-mode config.

This also fixes P2P enabling: due to the uCode
loading code shuffle moving the SKU check before
the EEPROM was read it was always false and would
always disable PAN/P2P.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

This will allow to have different behavior depending on the fw.
Different fw APIs require completely different implementation
of the mac80211 APIs. Each of these implementations is called an
op_mode.

The current op_mode is called DVM which states for dual virtual MAC.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

struct iwl_fw contains a string that describe the fw. This string
is now set by the iwl_parse_*_firmware.
This string is later used to update the cfg80211 data.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Bring MCU operations during device initialization to sync
with legacy driver.

This should fix following error:
phy0 -> rt2800pci_mcu_status: Error - MCU request failed,
no response from hardware
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add documentation on MCU communication, some of known commands and
their arguments. Supplement command ids.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/iwlwifi/iwl-core.c included 'iwl-agn.h' twice,
remove the duplicate.
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The second line of a printk statement must line up to the opening bracket.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also don't use so generic BRCMF_USB_FW_NAME as we may need different
firmwares in the future.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There were two dereferencing before checking for NULL static checker
complaints in this new file.  The list cursor is never NULL so that
check can be removed.  I moved the other dereference after the check.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use IW_HANDLER macro in ipw2100.c to declare wireless handlers.

Note: ipw2200.c already uses it.
Signed-off-by: NStanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cleanup whitespace, fix indentation and coding style.
Also remove debug messages that were flooding the log.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes indentation and the general coding style
in ar9003_mci.c. Also, minimize the amount of debug log
output generated by MCI.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

They are not needed since MCI will be enabled only for
AR9462 v2.0
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Use a separate function to enable/disable
  OneStepLookAhead.

* Remove unnecessary hardware SREV checks.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ATH9K_BTCOEX_SUPPORT is now used by both ath9k and ath9k_htc
to enable BT coexistence. Fix Kbuild to allow this.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the ability to remove BTCOEX support at compile time,
these checks are no longer needed.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>