Changes to support other Optima types, introduced an accidental
regression that caused 88E8059 to come up in 10Mbit/sec.

The Yukon Optima supports a reverse auto-negotiation feature that
was incorrectly setup, and not needed. The feature could be used to
allow wake-on-lan at higher speeds. But doing it correctly would require
other changes to initialization.
Reported-by: NPavel Mateja <pavel@netsafe.cz>
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

i825xx and xscale are "sub" Kconfigs to NET_VENDOR_INTEL, so
NET_VENDOR_INTEL should contain ALL the dependencies of the
"sub" Kconfigs.

Same with 8390 is a "sub" Kconfig to NET_VENDOR_NATSEMI, so
NET_VENDOR_NATSEMI needs to contains ALL the dependencies.

Freescale Kconfig only had fs_enet as a sub Kconfig, and already
contained the needed dependencies, just cleaned up the dependencies.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the tg3 version to 3.121.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During shutdown, it is impossible to reliably disable the timer and
reset_task threads.  Each thread can schedule the other, which leads to
shutdown code that chases its tail.

To fix the problem, this patch removes the ability of tg3_reset_task to
schedule a new timer thread.  To support this change, tg3_timer no
longer terminates itself, but rather goes into a polling mode.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible for multiple threads in the tg3 driver to each attempt to
schedule a run of tg3_reset_task().  The multiple tg3_reset_task
executions could all wind up on the same queue (and execute serially) or
wind up on the queues of another processor (which could execute in
parallel).  Either scenario is not what was truly desired.

This patch adds a new flag, TG3_FLAG_RESET_TASK_PENDING, and uses it to
determine whether or not to schedule another run of tg3_reset_task().
With the new flag comes two new functions to facilitate scheduling and
descheduling of tg3_reset_task().
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds code to attempt to obtain the PCI function number from
the device rather than accept the number handed by the kernel.  In
pass-through scenarios, the function number handed by the kernel may not
reflect the true function of the device.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a bug where the irq error cleanup path did not free all
the resources it allocated.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBen Li <benli@broadcom.com>
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the error recovery resource unwind path, it is possible for the
driver to attempt to unmap a fragment that hadn't been mapped.  This
patch fixes the problem by correcting the "last" parameter supplied.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new 4k tx bd segmentation code had a bug in the error cleanup path.
If the driver did not map all the physical fragments, the abort path
would wind up advancing the producer index beyond the point where the
setup code stopped.  This would ultimately turn into a tx recovery error
where the driver would expect the skb pointer to be set when it isn't.
This patch fixes the problem, and then makes the code a little easier to
understand.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

APE mutex register blocks are shared by all ports of multiport devices.
For some mutexing purposes, each function is assigned their own
register.  For other cases, each function is assigned its own request
and grant bits of a single register.  For the latter cases, the tg3
driver is incorrectly allowing each function to use the same set of
grant / request bits.  This patch fixes the code so that each function
uses the appropriate bitset.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add code to detect UE in case of Lancer.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Indicate to HW that the CQ is cleaned up before posting new RX buffers.
This prevents the HW to go into CQ full error condition.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If user tries to disable multicast promiscous mode, the adapter remains
in this mode as resetting the multicast promiscous mode was missing
in RX filter command. Fixed this.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use cpu_to_le32() for mcast_num field in RX filter command as this
field is of type u32.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Returning the max traffic classes on get requests simplifies
user space configurations because applications will know
explicitly how many traffic classes can be used.

Typical switch implementations use 2 or 3 traffic classes
so this not seen often today. And user space can learn
the number of traffic classes by return codes but this
allows user space to configure ixgbe correctly at the
start.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes some issues found in the buffer read portion of
ixgbe_host_interface_command()

- use `bi` as the buffer index counter instead of `i`
- add conversion to native cpu byte ordering on register read
- fix conversion from bytes to dword
- use dword_len instead of buf_len when reading the register
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Wrap SR-IOV specific functions in CONFIG_PCI_IOV to avoid compiler
warnings.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe_ieee_ets and ixgbe_ieee_pfc are intialized at
the same time. Do a check for both before configuring
IEEE802.1Qaz. Also max_frame was causing a sparse
warning resolved here as well.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

register_netdev() calls ndo_set_features() which may result in HW reset
which in turn will bring the laser back up.

This patch moves ixgbe_laser_tx_disable() below register_netdev()
in ixgbe_probe() to make sure laser is shut off on load.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Interface fails to obtain link on 82599 SFP in the following scenario:

1. Set advertised speed to GB:
ethtool -s eth0 advertise 0x20

2. Bring interface down
ip link set eth0 down

3. Issue any command that leads to a reset:
ethtool -t eth0

4. Bring link back up:
ip link set eth0 up

Following patch makes sure that the driver flaps the Tx laser every time
ixgbe_start_hw() is called, and not only when the speed is set.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The PHY cable length unit detection was not using the correct
the correct PHY data variable for I347AT4.
Signed-off-by: NTomasz Kantecki <tomasz.kantecki@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

e100 parts don't support vlan offload but they generally do
allow use of vlans in higher software layers via the 8021q module.
That said, there are a couple of really old revisions of e100
hardware that don't even allow the longer frame sizes
required for vlan use with standard MTU.

Use the VLAN_CHALLENGED flag to prevent vlan binding to these
devices.
Reported-by: NMichael Tokarev <mjt@tls.msk.ru>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
CC: Michael Tokarev <mjt@tls.msk.ru>
CC: David Lamparter <equinox@diac24.net>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This debugging message was recently added but it does not need to be as
alarming as a WARN.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 9e903e08 ("net: add skb frag size accessors") used frag_size
instead of skb_frag_size in this file.

Fixes this build error:

drivers/net/ethernet/xilinx/ll_temac_main.c: In function 'temac_start_xmit':
drivers/net/ethernet/xilinx/ll_temac_main.c:717:3: error: implicit declaration of function 'frag_size' [-Werror=implicit-function-declaration]
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Macintosh CS89x0 based ethernet cards use a Crystal Semiconductor (Now
Cirrus Logic) CS89x0 chip, so the mac89x0 driver should be in
drivers/net/ethernet/cirrus instead of drivers/net/ethernet/apple.

This also fixes a build problem, as the driver needs a header file from the
cirrus directory:

drivers/net/ethernet/apple/mac89x0.c:107:20: error: cs89x0.h: No such file or directory
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While the SC92031 could be found on fake "Realtek" NICs, it has no
relationship to Realtek, and is actually from Silan.

Create a new subdirectory for silan and move sc92031 there.
Signed-off-by: NCesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The `#define filename' screws up the expansion of
DEFINE_DYNAMIC_DEBUG_METADATA:

drivers/net/ethernet/i825xx/3c505.c: In function 'send_pcb':
drivers/net/ethernet/i825xx/3c505.c:390: error: expected identifier before string constant
drivers/net/ethernet/i825xx/3c505.c:390: error: expected '}' before '.' token
drivers/net/ethernet/i825xx/3c505.c:436: error: expected identifier before string constant
drivers/net/ethernet/i825xx/3c505.c:435: error: expected '}' before '.' token
drivers/net/ethernet/i825xx/3c505.c: In function 'start_receive':
drivers/net/ethernet/i825xx/3c505.c:557: error: expected identifier before string constant
drivers/net/ethernet/i825xx/3c505.c:557: error: expected '}' before '.' token
drivers/net/ethernet/i825xx/3c505.c: In function 'receive_packet':
drivers/net/ethernet/i825xx/3c505.c:629: error: expected identifier before string constant

etc

So remove that #define and "open-code" it.

Cc: Philip Blundell <philb@gnu.org>
Cc: David Miller <davem@davemloft.net>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Standardize the style for compiler based printf format verification.
Standardized the location of __printf too.

Done via script and a little typing.

$ grep -rPl --include=*.[ch] -w "__attribute__" * | \
  grep -vP "^(tools|scripts|include/linux/compiler-gcc.h)" | \
  xargs perl -n -i -e 'local $/; while (<>) { s/\b__attribute__\s*\(\s*\(\s*format\s*\(\s*printf\s*,\s*(.+)\s*,\s*(.+)\s*\)\s*\)\s*\)/__printf($1, $2)/g ; print; }'

[akpm@linux-foundation.org: revert arch bits]
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

o Updated version number to 5.0.25

o Do not hold onto RESETTING_BIT for entire duration of LED/ beacon test.
  Instead, just checking for RESETTING_BIT not set before sending config_led
  command down to card.

o Take rtnl_lock instead of RESETTING_BIT for beacon test while sending
  config_led command down to make sure interface cannot be brought up/ down.

o Allocate and free resources if interface is down before
  sending the config_led command. This is to make sure config_led
  command sending doesn't fail.

o Clear QLCNIC_LED_ENABLE bit if beacon/ LED test fails to start.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If promiscous mode setting fails, reset loopback mode setting in firmware.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In fw reset path, we should consider any change in device state as an
ack from the other driver. When that happens, we don't have to wait for
an explicit ack.
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the normal descriptor structure
to work fine on new GMAC Synopsys chips.

Normal descriptors were designed on the old MAC10/100
databook 1.91 where some bits were reserved: for example
the tx checksum insertion and rx checksum offload.

The patch maintains the back-compatibility with old
MAC devices (tested on STx7109 MAC10/100) and adds new
fields that actually new GMAC devices can use.

For example, STx7109 (MAC10/100) will pass from the platform
  tx_coe = 0, enh_desc = 0, has_gmac = 0.
A platform like Loongson1B (GMAC) will pass:
  tx_coe = 1, enh_desc = 0, has_gmac = 1.

Thanks to Kelvin, he enhanced the normal descriptors for
GMAC (on MIPS Loongson1B platform).
Signed-off-by: NKelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAngus Clark <angus.clark@st.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch fixes a bug while checking the HW cap reg
on old MAC10/100 where this feature is not available.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow for MAC Address change of VF(SR-IOV case) on the fly- First add and then
delete MAC Address to allow for 'out of pool' errors.
When MAC Addr configured from a VM, the MAC on the NIC will aleady have
the supplied MAC,so just copy the supplied MAC to the netdev structure
before returning success to the stack
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moved the .sge. field's population inside be_cmd_hdr_prepare.
Populating wrb->tag0 and tag1 inside be_cmd_hdr_prepare
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>