We already implement this workaround, but it was missing its name.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Stupid userspace (there is no evil userspace in debugfs by assumption)
might provoke a leak since we allocate the new array without holding
any locks. Drop in an unconditional kfree to deal with this - kfree
can handle NULL.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

Currently i915_pipe_crc_read() will drop pipe_crc->lock for the entire
duration of the copy_to_user() loop, which means it'll access
pipe_crc->entries without any protection. If another thread sneaks in
and frees pipe_crc->entries the code will oops.

Reorganize the code to hold the lock around everything except
copy_to_user(). After the copy the lock is reacquired and the the number
of available entries is rechecked.

Since this is a debug feature simplify the error handling a bit by
consuming the crc entry even if copy_to_user() would fail.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

pipe_crc->entries[] is an array so allocate with kcalloc() instead of
kzalloc().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Set the pipe_crc->entries pointer while holding the relevant spinlock.
Doesn't matter too much since a spurious pipe crc interrupt would then
just update one entry but later that entry would get cleared when head
and tail are both set to 0. But being a bit more paranoid doesn't hurt.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add the missing CRC control register value for DP port D on CHV.
Untested as I don't have a CHV machine with DP on port D.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add a check to only allow DP D on chv, not vlv.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To get stable CRCs from the DP CRC source we need to reset the
scrambler for each frame. Enable the reset feature when grabbing
CRCs for pipe C on CHV. Pipes A and B were already covered due
sharing the code with VLV.

We can safely extend PIPE_SCRAMBLE_RESET_MASK to deal with CHV since
the extra bit was MBZ on the older platforms.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

intel-gpu-tools now generates the render state with license headers and
the version of i-g-t that generated the files.

A similar patch was previously sent but wasn't actually generated with
the make target so was lacking the i-g-t revision. So here another
version before we totally forget about this.

Cc: Armin Reese <armin.c.reese@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

No functional changes.

v2 (Paulo): Rebase.
v3: Accept Daniel's suggestions:
    * remove unclear and duplicated explanation.
    * remove marketing like doc and replace by a simple one.
    * remove bdw_fbc_sw_flush documentation.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Due to hardware limitations on BYT, MIPI Port C DPI Enable bit
does not get set. To check whether DSI Port C was enabled in BIOS,
check the Pipe B enable bit for DSI Port C. In hardware, DSI Port C
is linked with Pipe B.

v2: Addressed review comments of Jani, Nikula
    - Used platform checks for this software workaround for BYT
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Common bit to be used for both DSI Port A & DSI Port C.
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

DSI Pll1 is used for enabling DSI on Port C.

v2: Addressed review comments of Jani
    - Used & operator instead of == for intel_dsi->ports
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Was missing.

Issue: VIZ-4701
Signed-off-by: NMichael H. Nguyen <michael.h.nguyen@intel.com>
Reviewed-by: NJon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

No functional changes. This is just the begin of a FBC rework.

v2 (Paulo):
  - Revert intel_fbc_init() changed parameter.
  - Revert set_no_fbc_reason() rename.
  - Rebase.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

After a bit of irc discussion we've concluded that it would be prudent
to check that callers use the mask/enable paramters correctly. So add
a WARN_ON.

Spurred by Damien's bugfix which added _MASKED_FIELD.

v2: We use WARN_ON(1) a lot to catch default cases in switch blocks
which should always be extended. So this doesn't work really. Dunno
why gcc only started complaining when I've moved the WARN out of the
static inline helper to address a feedback from Jani.

Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

Similar to a patch from Thomas Daniel for lrc contexts. This keeps
both sides somewhat in sync and should make Dave Gordon happy.

Note that both the wa and the golden context init code suffer a bit
from an inssuficient split into driver load and hw init code. Which
means we have a bunch of tests all over the place to check whether the
one-time initialization has been done already or not.

All that one-tim code should be moved into the one-time ring setup
code, but that's work for later.

Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NDave Gordon <david.s.gordon@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Remove the function intel_output_name() that is not used anywhere.

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Added the request structure's 'uniq' identifier to the trace information. Also
renamed the '_complete' trace event to '_notify' as it actually happens in the
IRQ 'notify_ring()' function. The intention is to add a new '_complete' trace
event which occurs when a request structure is actually marked as complete.
However, at the moment the completion status is re-tested every time the query
is made so there isn't a completion event as such.

v2: New patch added to series.

v3: Rebased to remove completion caching as that is apparently contentious.

Change-Id: Ic9bcde67d175c6c03b96217cdcb6e4cc4aa45d67
For: VIZ-4377
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Reviewed-by: NThomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For debugging purposes, it is useful to be able to uniquely identify a given
request structure as it works its way through the system. This becomes
especially tricky once the seqno value is lazily allocated as then the request
has nothing but its pointer to identify it for much of its life.

Change-Id: Ie76b2268b940467f4cdf5a4ba6f5a54cbb96445d
For: VIZ-4377
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Reviewed-by: NThomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There is a general theory that kzmalloc is better/safer than kmalloc, especially
for interesting data structures. This change updates the request structure
allocation to be zero filled.

This also fixes crashes in the reset code. Quoting Mika's patch:

"Clean the request structure on alloc. Otherwise we might end up
referencing uninitialized fields.  This is apparent when we try to
cleanup the preallocated request on ring reset, before any request has
been submitted to the ring.  The request->ctx is foobar and we end up
freeing the foobarness."

Note that this fixes a regression introduced in

commit 9eba5d4a
Author: John Harrison <John.C.Harrison@Intel.com>
Date:   Mon Nov 24 18:49:23 2014 +0000

    drm/i915: Ensure OLS & PLR are always in sync

References: https://bugs.freedesktop.org/show_bug.cgi?id=86959
References: https://bugs.freedesktop.org/show_bug.cgi?id=86962
References: https://bugs.freedesktop.org/show_bug.cgi?id=86992
Change-Id: I68715ef758025fab8db763941ef63bf60d7031e2
For: VIZ-4377
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Reviewed-by: NThomas Daniel <Thomas.Daniel@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The display related patches earlier in this series were edited during merge to
improve the request unreferencing. Specifically, the need for de-referencing at
interrupt time was removed. However, the resulting code did a 'deref(req) ; req
= NULL' sequence rather than using the 'req_assign(req, NULL)' wrapper. The two
are functionally equivalent, but using the wrapper is more consistent with all
the other places where requests are assigned.

Note that the whole point of the wrapper is that using it everywhere that
request pointers are assigned means that the reference counting is done
automatically and can't be accidentally forgotten about. Plus it allows simpler
future maintainance if the reference counting mechanisms ever need to change.

For: VIZ-4377
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we extend the commit_plane handlers for each plane type to be able to
handle fb=0, then we can easily implement plane disable via the
update_plane handler.  The cursor plane already works this way, and this
is the direction we need to go to integrate with the atomic plane
handler.  We can now kill off the type-specific disable functions, as
well as the redundant intel_plane_disable() (not to be confused with
intel_disable_plane()).

Note that prepare_plane_fb() only gets called as part of update_plane
when fb!=NULL (by design, to match the semantics of the atomic plane
helpers); this means that our commit_plane handlers need to handle the
frontbuffer tracking for the disable case, even though they don't handle
it for normal updates.

v2:
 - Change BUG_ON to WARN_ON (Ander/Daniel)

v3:
 - Drop unnecessary plane->crtc check since a previous patch to plane
   update ensures that plane->crtc will always be non-NULL, even for
   disable calls that might pass NULL from userspace.  (Ander)
 - Drop a s/crtc/plane->crtc/ hunk that was unnecessary.  (Ander)

v4:
 - Fix missing whitespace (Ander)

v5:
 - Use state's crtc rather than plane's crtc in
   intel_check_primary_plane().  plane->crtc could be NULL, but we've
   already fixed up state->crtc to ensure it's non-NULL (even if
   userspace passed it as NULL during a disable call).  (Ander)
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When disabling a plane, it is legal to pass crtc = NULL.  Since planes
on Intel hardware are tied to a fixed CRTC, go ahead and set state->crtc
to the appropriate crtc in cases where it is passed to us as NULL.

In a future patch, we will start using the update handler for plane
disables, so this will help ensure we always have a non-NULL crtc
pointer to work with.
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Our .update_plane() handlers do the same check/prepare/commit/cleanup
steps regardless of plane type.  Consolidate them all into a single
function that calls check/commit through a vtable.
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

All plane update functions need to unpin the old framebuffer when
flipping to a new one.  Pull this logic into a separate function to ease
the integration with atomic plane helpers.

v2: Don't wait for vblank if we don't have an old fb to cleanup (Ander)

v3: Really don't wait for vblank if we don't have an old fb to cleanup.
    Previous version only handled this for primary planes; we need the
    same change on cursors/sprites too!  (Ander)
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The 'prepare' step for all types of planes are pretty similar;
consolidate the three 'prepare' functions into a single function.  This
paves the way for future integration with the atomic plane handlers.

Note that we pull the 'wait for pending flips' functionality out of the
primary plane's prepare step and place it directly in the 'setplane'
code.  When we move to the atomic plane handlers, this code will be in
the 'atomic begin' step.

v2: Update GEM fb tracking for physical cursors also (Ander)
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reviewed-by: NBob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Primary and sprite planes have already been refactored to include a
'prepare' step which handles all the commit-time operations that could
fail (i.e., pinning buffers and such).  Refactor the cursor commit in a
similar manner.

For simplicity and consistency with other plane types, we also switch to
using intel_pin_and_fence_fb_obj() to perform our pinning for
non-physical cursors.  This will allow us to more easily migrate the
code into the atomic 'begin' handler in a plane-agnostic manner in a
future patchset.

v2:
 - Update GEM fb tracking for physical cursors too. (Ander)
 - Use intel_unpin_fb_obj() rather than
   i915_gem_object_unpin_from_display_plane() and do so while holding
   struct_mutex.  (Ander)
 - Update plane->fb in commit_cursor_plane.  This isn't really necessary
   since the DRM core does this for us in __setplane_internal(), but
   doing it in our driver once we know we're going to succeed helps
   avoid confusion. (Ander)
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

After some refactor intel_primary_plane_setplane() does the same
as intel_pipe_set_base() so we can get rid of it and replace the calls
with intel_primary_plane_setplane().

v2: take Ville's comments:
	- get the right arguments for update_plane()
	- use drm_crtc_get_hv_timing()

v3 (by Matt):
 - Rebase to latest di-nightly codebase
 - Use primary->funcs->update_plane() in __intel_set_mode()
 - Use primary->funcs->disable_plane() in intel_crtc_disable()

v4 (by Matt):
 - Drop redundant calls to intel_crtc_wait_for_pending_flips() before
   calling update_plane() (Ville)
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Acked-and-mourned-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Merge it into the plane update_plane() callback and make other
users use the update_plane() functions instead.

The fb != crtc->cursor->fb was already inside intel_crtc_cursor_set_obj()
so we fold intel_crtc_cursor_set_obj() inside intel_commit_cursor_plane()
and merge both paths into one.

v5 (by Matt):
 - Rebase onto latest di-nightly codebase
 - Drop extra unreference call when we fail to pin (Ville)

Reviewed-by(v4): Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to get hdisplay and vdisplay in a few places so create a
helper to make our job easier.

Note that drm_crtc_check_viewport() and intel_modeset_pipe_config() were
previously making adjustments for doublescan modes and vscan > 1 modes,
which was incorrect.  Using our new helper fixes this mistake.

v2 (by Matt): Use new stereo doubling function (suggested by Ville)

v3 (by Matt):
 - Add missing kerneldoc (Daniel)
 - Use drm_mode_copy() (Jani)

v4 (by Matt):
 - Drop stereo doubling function again; add 'stereo only' flag
   to drm_mode_set_crtcinfo() instead (Ville)

v5 (by Matt):
 - Note behavioral change in drm_crtc_check_viewport() and
   intel_modeset_pipe_config(). (Ander)
 - Describe new adjustment flags in drm_mode_set_crtcinfo()'s
   kerneldoc. (Ander)

Cc: dri-devel@lists.freedesktop.org
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We already have it for chv, but was missing for bdw.
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to program both port registers during dual link enable path.

v2: Address review comments by Jani
    - Used a for loop instead of do-while loop.

v3: Used for_each_dsi_port macro instead of for loop

v4: Renamed mode_hactive variable to mode_hdisplay
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to program both port registers during dual link disable path.

v2: Address review comments by Jani
    - Used a for loop instead of do-while loop.

v3: Used for_each_dsi_port macro instead of for loop

v4: Added comments for the usage of AFE latchout bit
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

hactive, hfp, hbp, hsync needs to be halved for dual link MIPI Panels.
Accordingly timing related mmio regs needs to be programmed for both MIPI Ports.

v2: Address review comments by Jani
    - Used a for loop instead of do-while loop

v3: Used for_each_dsi_port macro instead of for loop
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Instead of pipe configuration reg, cck reg to be used for checking whether
DSI Pll is getting locked or not.

v2: dpio_lock unlocked now in case DSI PLL lock fails
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For Dual link MIPI Panels, dsipll clock for both DSI0 and DSI1 needs to be enabled.

v2: Address review comments by Jani
    - Added wait time for PLL to be locked.

v3: separate patch created for cck read for checking PLL to be locked
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For dual link MIPI panels, SHUTDOWN packet needs to send to both Ports
A & C during MIPI encoder disabling sequence. Similarly, TURN ON packet
to be sent to both Ports during MIPI encoder enabling sequence.

v2: Address review comments by Jani
    - Used a for loop instead of do-while loop.

v3: Used for_each_dsi_port macro instead of for loop
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For dual link MIPI Panels, each port needs half of pixel clock. Pixel overlap
can be enabled if needed by panel, then in that case, pixel clock will be
increased for extra pixels.

v2 : Address review comments by Jani
     - Removed the bit mask used for ->dual_link
     - Used DSI instead of MIPI for #define variables

v3: Added the VLV_DISPLAY_BASE to VLV_CHICKEN_3 register
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>