At the moment when HDMI video output is stopped, we just clear the
enable bit and return. While it's unclear if this can cause any issues,
I think it's still better to wait for FRAMEDONE interrupt after clearing
the enable bit so that we're sure the HDMI IP has finished.

As we don't have any ready-made irq handling for HDMI, and this only
needs to be done when disabling the HDMI output, this patch implements a
simple loop with sleep, polling the FRAMEDONE bit.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Error handling in hdmi_power_on_full() is not correct, and could leave
resources unfreed.

Fix this by arranging the error labels correctly.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Improve the DISPC debug print for scaling.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The current driver does both x and y decimation on OMAP3 DSS. Testing
shows that x decimation rarely works, leading to underflows.

The exact reason for this is unclear, as the underflows seem to happen
even with low pixel clock rates, and I would presume that if the DSS can
manage a display with 140MHz pixel clock, it could manage x decimation
with factor 2 with a low pixel clock (~30MHz).

So it is possible that there is a problem somewhere else, in memory
management, or DSS DMA, or similar. I have not found anything that would
help this.

So, to fix the downscaling scaling, this patch removes x decimation for
OMAP3. This will limit some of the more demanding downscaling scenarios,
but one could argue that using DSS to downscale such a large amount is
insane in the first place, as the produced image is rather bad quality.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The DISPC's scaling code seems to presume that decimation always
succeeds, and so we always do find a suitable downscaling setup.
However, this is not the case, and the algorithm can fail.

When that happens, the code just proceeds with wrong results, causing
issues later.

Add the necessary checks to bail out if the scaling algorithm failed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The DISPC driver uses 64 bit arithmetic to calculate the required clock
rate for scaling. The code does not seem to work correctly, and instead
calculates with 32 bit numbers, giving wrong result.

Fix the code by typecasting values to u64 first, so that the
calculations do happen in 64 bits.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

pixel_inc and row_inc work differently on OMAP2/3 and OMAP4+ DSS. On
OMAP2/3 DSS, the pixel_inc is _not_ added by the HW at the end of the
line, after the last pixel, whereas on OMAP4+ it is.

The driver currently works for OMAP4+, but does not handle OMAP2/3
correctly, which leads to tilted image when row_inc is used.

This patch adds a flag to DISPC driver so that the pixel_inc is added
when required.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

On OMAP3/AM43xx some scaling factors cause underflows/synclosts. After
studying this, I found that sometimes the driver uses three-tap scaling
with downscaling factor smaller than x0.5. This causes issues, as x0.5
is the limit for three-tap scaling.

The driver has FEAT_PARAM_DOWNSCALE parameter, but that seems to be for
five-tap scaling, which allows scaling down to x0.25.

This patch adds checks for both horizontal and vertical scaling. For
horizontal the HW always uses 5 taps, so the limit is x0.25.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

After calculating the required decimation for scaling, the dispc driver
checks once more if the resulting configuration is valid by calling
check_horiz_timing_omap3().

Earlier calls to this function have correctly used in_width and
in_height as parameters, but the last call uses width and height. This
causes the driver to possibly reject scaling that would work.

This patch fixes the parameters.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DISPC needs even input buffer width for YUV modes. The DISPC driver
doesn't check this at the moment (although omapdrm does), but worse,
when DISPC driver does x predecimation the result may be uneven. This
causes sometimes sync losts, underflows, or just visual errors.

This patch makes DISPC driver return an error if the user gives uneven
input width for a YUV buffer. It also makes the input width even in case
of predecimation.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Errata i631 description:

"When in YUV4:2:0 format in 1D burst, the DISPC DMA skips lines when
fetching Chroma sampling."

Workaround:

"If YUV4:2:0-1D burst is required: Set
DISPC_VIDp_ATTRIBUTES[22]DOUBLESTRIDE to 0x0 and
DISPC_VIDp_ATTRIBUTES[13:12]ROTATION to 0x1 or 0x3"

The description is somewhat confusing, but testing has shown that DSS
fetches extra rows from memory when using NV12 format in 1D mode. If the
memory after the framebuffer is inaccessible, this leads to OCP errors.

The driver always uses DOUBLESTRIDE=0 when using 1D mode, so we only
need to handle the ROTATION part.

The issue exist on all OMAP4 and OMAP5 based DSS IPs.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that we are using components in omapdss, there's no need for
separate handling of dss and dispc driver init. Thus we can move the dss
and dispc init and unit func pointers to the lists we use for the other
dss submodules.

We can now also handle errors returned by the registration functions
properly: if registering a driver fails, we can stop processing and
return the error.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

omapdss kernel module contains drivers for multiple devices, one for
each DSS submodule. The probing we have at the moment is a mess, and
doesn't give us proper deferred probing nor ensure that all the devices
are probed before omapfb/omapdrm start using omapdss.

This patch solves the mess by using the component system for DSS
submodules.

The changes to all DSS submodules (dispc, dpi, dsi, hdmi4/5, rfbi, sdi,
venc) are the same: probe & remove functions are changed to bind &
unbind, and new probe & remove functions are added which call
component_add/del.

The dss_core driver (dss.c) acts as a component master. Adding and
matching the components is simple: all dss device's child devices are
added as components.

However, we do have some dependencies between the drivers. The order in
which they should be probed is reflected by the list in core.c
(dss_output_drv_reg_funcs). The drivers are registered in that order,
which causes the components to be added in that order, which makes the
components to be bound in that order. This feels a bit fragile, and we
probably should improve the code to manage binds in random order.
However, for now, this works fine.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

We have a list of function pointers to dss submodule uninit functions.
It makes sense to do the uninit in the reverse order to init, but that
is not currently the case.

This patch reorders the uninit calls to be the reverse of init order.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

The following patches will add component handling to omapdss, improving
the handling of deferred probing. However, at the moment we're using
quite a lot of __inits and __exits in the driver, which prevent normal
dynamic probing and removal.

This patch removes most of the uses of __init and __exit, so that we can
register drivers after module init, and so that we can unregister
drivers even if the module is built-in.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

The return value of dss_init_ports() is not handled at all, causing
crashes later if the call failed.

This patch adds the error handling, and we also move the call to a
slightly earlier place to make bailing out easier.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Refactor dss probe function by extracting the setup for video plls into
a separate function. The call to this function is also moved to a
slightly earlier phase, so that in error case we can bail out more
easily.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

We have a flag, 'dss_initialized', which tells omapfb and omapdrm if
omapdss is available. At the moment it can be set even if the dss
submodules are not all ready, in case something gets deferred.

Move the flag to dss_core driver so that it'll signal the availability
of the dss drivers move accurately.

For now, it'll signal that dss_core is ready, which is not quite correct
but still better than previously.  The following patches will add
component system to omapdss, and after those patches 'dss_initialized'
will signal that all the submodules are ready.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Since kobject_init_and_add takes a format string, make sure that the
passed in name cannot be accidentally parsed.
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

There is a constraint in the OMAP4 HDMI IP that requires to use
the 8-channel code when transmitting more than two channels.

The constraint doesn't apply for OMAP5 so don't force the channel
allocation in the sound driver as it can be done specifically for
OMAP4 later in the hdmi4 core.
Signed-off-by: NMisael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NMark Brown <broonie@kernel.org>

Downmix inhibit in HDMI_CORE_FC_AUDICONF3 register is in
bit 4 while CEA861_AUDIO_INFOFRAME_DB5_DM_INH sets bit 7.
Signed-off-by: NMisael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

As per TRM, HDMI_WP_AUDIO_CFG[2] LEFT_BEFORE = 0 is reserved,
so it must always be set to 1 (the first sample is the left).
Signed-off-by: NMisael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

OMAP4 HDMI IP uses the 8-channel layout with 8-channel speaker
allocation mask when transmitting more than two channels.  But
the channel count field (CC) of the Audio InfoFrame's DB1 is
not updated for 8-channels.

As per HDMI Compliance Test 7.31 "Audio InfoFrame", CC = 7 is
required for 8-channels CA masks (0x13 and 0x1F).
Signed-off-by: NMisael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Since 39b2bbe3 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.

Also make use of gpiod_get*_optional where applicable.

Apart from simplification of the affected drivers this is another step
towards making the flags argument to gpiod_get*() mandatory.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add handling of missed events in omap_dss_pm_notif which are
needed to support hibernation (suspend to disk).
Signed-off-by: NGrygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We don't need VT switch when suspending/resuming, so disable it. This
speeds up suspend/resume.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: NeilBrown <neil@brown.name>

It was found that having two displays enabled and having an NV12 overlay
on one of the displays will cause underflows/synclosts. Debugging this
pointed to some issue with MFLAG.

It is unclear why this issue is happening, but it looks like there is a
HW bug related to MFLAG and FIFO management. Disabling MFLAG makes this
issue go away, but then we lose the benefit of MFLAG. Also forcing MFLAG
always on makes the issue go away.

Also, using certain values for MFLAG_START, MFLAG thresholds and PRELOAD
makes the issue go away, but there was no obvious logic to which values
work and which don't.

As a workaround until more information about this is found, force MFLAG
always on to make NV12 usable.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

OMAP5 has support for MFLAG feature, which allows DSS to dynamically
increase the priority of DISPC's DMA traffic. At the moment we don't
have support for it.

It was noticed that on DRA7 with high bandwidth use cases we see FIFO
underflows. Implementing MFLAG support removed those underflows.
Interestingly, on OMAP5 uEVM no such overflows were seen.

This patch adds a simple MFLAG implementation, where we use a fixed
MFLAG threshold value based on the FIFO size. The thresholds are set to
4/8 of fifo size for low threshold, and 5/8 of fifo size for high
threshold.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

At the moment we don't setup FIFO thresholds by default in omapdss. It's
supposed to be done by the user of omapdss. And that is missing from
omapdrm, causing unoptimal thresholds to be used when using omapdrm.

While I believe it's in theory better to allow the user of omapdss to
setup the fifo thresholds, in practice we always use the same values,
and we could as well setup the thresholds in omapdss.

Furthermore, in omapdss init we always swap the FIFO used for GFX and WB
overlays, but we don't swap the FIFO thresholds for those overlays
(which is the reason for omapdrm using unoptimal HW reset values). So
it would make sense to setup the thresholds to account for the swapping
of the FIFOs.

So, this patch adds code to setup default FIFO tresholds at omapdss
init.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Dispc driver presumes that the callers handle locking for all normal
functions. However, omapdrm doesn't handle this, and presumes that all
overlay manager registers are private to that overlay manager, and thus
presumes that configurations for overlay managers can be written via
different threads freely.

For many registers the above is true. The exceptions are DISPC_CONTROL
and DISPC_CONFIG registers, which contain bits for both LCD and TV
overlay managers.

Fixing this properly in omapdrm means a big omapdrm rewrite. So, for
now, add locking to dispc for the problematic registers.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: NSomnath Mukherjee <somnath@ti.com>

omapdrm doesn't always configure the overlays correctly, causing the
overlay setup functions to be called with zero timings. This leads to
division by zero error.

This happens, for example, when a HDMI cable is not connected, but a
user tries to setup a plane with scaling.

Fixing omapdrm is a big job, so for now let's check for the bad timings
in DISPC and return an error.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The common 'struct videomode' does not have a flag to select when the
sync signals should be driven.

The default behavior of DISPC HW is to drive the sync signal on the
opposite pixel clock edge from data signal, which is also what the
videomode_to_omap_video_timings() uses.

However, it looks like what panels usually expect is that the data and
sync signals are driven on the same edge, so let's change
videomode_to_omap_video_timings() to set the sync_pclk_edge accordingly.

Note that this only affect panels drivers that use
videomode_to_omap_video_timings(), probably when getting the video
timings directly from DT data. The drivers can still configure the
sync_pclk_edge independently if they so wish.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

When configuring the lcd timings, instead of writing enum values
directly to the HW, use switch-case to get the value to be programmed.

This is safer and also allows us to change the enum values.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DISPC can drive data lines either on rising or falling pixel clock edge,
which can be configured by the user.

Sync lines can also be driven on rising or falling pixel clock edge, but
additionally the HW can be configured to drive the sync lines on
opposite clock edge from the data lines.

This opposite edge setting does not make any sense, as the same effect
can be achieved by just setting the sync lines to be driven on the other
edge compared to the data lines. It feels like some kind of backward
compatibility option, even if all DSS versions seem to have the same
implementation.

To simplify the code and configuration of the signals, and to make the
dispc timings more compatible with what is used on other platforms,
let's just remove the whole opposite-edge support.

The drivers that used OMAPDSS_DRIVE_SIG_OPPOSITE_EDGES setting are
changed so that they use the opposite setting from the data edge.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

TFP410 requires that DE is active high and the data and syncs are driven
on rising pixel clock edge. However, at the moment the driver doesn't
request such syncs, and the end result is that the sync settings depend
on default values, which are not right in all cases.

Set the sync values explicitly.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The DISPC driver checks that the buffer address is not 0. However, when
using TILER, the address space is TILER specific and 0 is a valid
address.

Fix the check to allow address of 0 for TILER.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Nsrinivas pulukuru <srinivas.pulukuru@ti.com>

omapdss's sysfs directories for displays used to have 'name' file,
giving the name for the display. This file was later renamed to
'display_name' to avoid conflicts with i2c sysfs 'name' file. Looks like
at least xserver-xorg-video-omap3 requires the 'name' file to be
present.

To fix the regression, this patch creates new kobjects for each display,
allowing us to create sysfs directories for the displays. This way we
have the whole directory for omapdss, and there will be no sysfs file
clashes with the underlying display device's sysfs files.

We can thus add the 'name' sysfs file back.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: NNeilBrown <neilb@suse.de>

It has been observed that the current SDA-HOLD time is too short for
some board/cable/monitor combinations. Increase the SDA-HOLD time to
1000ns.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

AM43xx supports pixel clock divider of 1, just like all OMAP3+ SoCs. Fix
the minimum divider value.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Decrementing the reference count of the previous endpoint node allows to
use the of_graph_get_next_endpoint function in a for_each_... style macro.
All current users of this function that pass a non-NULL prev parameter
(that is, soc_camera and imx-drm) are changed to not decrement the passed
prev argument's refcount themselves.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>