Fill in asic family specific versions rather than
using the generic version.  This lets us handle asic
specific differences more easily.  In this case, we
disable sw swapping of the rtpr writeback value on
r6xx+ since the hw does it for us.  Fixes bogus
rptr readback on BE systems.

v2: remove missed cpu_to_le32(), add comments
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We need more control over the ordering of dpm init with
respect to the rest of the asic.  Specifically, the SMC
has to be initialized before the rlc and cg/pg.  The pm
code currently initializes late in the driver, but we need
it to happen much earlier so move pm handling into the asic
specific callbacks.

This makes dpm more reliable and makes clockgating work
properly on CIK parts and should help on SI parts as well.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We need to reorder the driver init sequence to better accomodate
dpm which needs to be loaded earlier in the init sequence.  Move
fw init up so that it's available for dpm init.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The vram scratch buffer needs to be initialized
before the mc is programmed otherwise we program
0 as the GPU address of the default GPU fault
page.  In most cases we put vram at zero anyway and
reserve a page for the legacy vga buffer so in practice
this shouldn't cause any problems, but better to make
it correct.

Was changed in:
6fab3febReported-by: NFrankR Huang <FrankR.Huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Similar to separating the UVD code, just put the DMA
functions into separate files.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Our different hardware blocks are actually completely
separated, so it doesn't make much sense any more to
structure the code by pure chipset generations.

Start restructuring the code by separating our the UVD block.

v2: updated commit message
v3: rebased and restructurized start/stop functions for kv dpm.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Now that we have callbacks for [rw]ptr handling we can
remove the special handling for the DMA rings and use
the callbacks instead.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The hardware just doesn't support this correctly.
Disable it before we accidentally write anywhere we shouldn't.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When we PG (powergate) UVD, we need to re-initialize it
before we can use it again.

v2: rebase on UVD stop fixes
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

No longer used now that we use the async dma engines or
CP DMA for bo copies.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Uses the wrong array size for some asics which can lead
to garbage getting written to registers.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=60674Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Otherwise just reinitialize from scratch on resume,
and so make it more likely to succeed.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

For r6xx+ asics.  This mirrors the behavior of pre-r6xx
asics.  We need to program the MC even if something
else in startup() fails.  Failure to do so results in
an unusable GPU.

Based on a fix from: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Removing the clock/power or resetting the VCPU can cause
hangs if that happens in the middle of a register write.

Stall the memory and register bus before putting the VCPU
into reset. Keep it in reset when unloading the module or
suspending.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Changing the UVD BOs offset on suspend/resume doesn't work because the VCPU
internally keeps pointers to it. Just keep it always pinned and save the
content manually.

Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=66425

v2: fix compiler warning
v3: fix CIK support

Note: a version of this patch needs to go to stable.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The current radeon driver initialization routines, when using KMS, are written
so that the IRQ installation routine is called before initializing the WB buffer
and the CP rings. With some ASICs, though, the IRQ routine tries to access the
GFX_INDEX ring causing a call to RREG32 with the value of -1 in
radeon_fence_read. This, in turn causes the system to completely hang with some
cards, requiring a hard reset.

A call stack that can cause such a hang looks like this (using rv515 ASIC for the
example here):
 * rv515_init (rv515.c)
 * radeon_irq_kms_init (radeon_irq_kms.c)
 * drm_irq_install (drm_irq.c)
 * radeon_driver_irq_preinstall_kms (radeon_irq_kms.c)
 * rs600_irq_process (rs600.c)
 * radeon_fence_process - due to SW interrupt (radeon_fence.c)
 * radeon_fence_read (radeon_fence.c)
 * hang due to RREG32(-1)

The patch moves the IRQ installation to the card startup routine, after the ring
has been initialized, but before the IRQ has been set. This fixes the issue, but
requires a check to see if the IRQ is already installed, as is the case in the
system resume codepath.
I have tested the patch on three machines using the rv515, the rv770 and the
evergreen ASIC. They worked without issues.

This seems to be a known issue and has been reported on several bug tracking
sites by various distributions (see links below). Most of reports recommend
booting the system with KMS disabled and then enabling KMS by reloading the
radeon module. For some reason, this was indeed a usable workaround, however,
UMS is now deprecated and disabled by default.

Bug reports:
https://bugzilla.redhat.com/show_bug.cgi?id=845745
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/561789
https://bbs.archlinux.org/viewtopic.php?id=156964Signed-off-by: NAdis Hamzić <adis@hamzadis.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

radeon currently uses a drm function to get the speed capabilities for
the bus, drm_pcie_get_speed_cap_mask. However, this is a non-standard
method of performing this detection and this patch changes it to use
the max_bus_speed attribute.

From: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com>
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The chip id for SUMO2 isn't used.

fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=63935Tested-By: NDave Witbrodt <dawitbro@sbcglobal.net>
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Instead of duplicating the code over and over again, just use a single
function to handle the clock calculations.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Just power down the PLL when we get a VCLK or DCLK of zero.
Enabling the bypass mode early should also allow us to
switch UVD clocks on the fly.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Avoid confusion with the *REG32_P mask macro.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

v2: set UVD tiling config for rv730
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NJerome Glisse <jglisse@redhat.com>

v2: avoid 64bit divide
v3: rv740 uses the evegreen upll configuration
Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NJerome Glisse <jglisse@redhat.com>

Just everything needed to decode videos using UVD.

v6: just all the bugfixes and support for R7xx-SI merged in one patch
v7: UVD_CGC_GATE is a write only register, lockup detection fix
v8: split out VRAM fallback changes, remove support for RV770,
    add support for HEMLOCK, add buffer sizes checks
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add a per-asic MC (memory controller) mask which holds the
mak address mask the asic is capable of.  Use this when
calculating the vram and gtt locations rather using asic
specific functions or limiting everything to 32 bits.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This is required to get the reference clock used
by the gfx engine for things like timestamps. Fixes
support for GL extensions the use timestamps on
certain boards.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

- r6xx actually uses a slightly different packet format,
although both formats seem to work ok.
- r7xx doesn't have the count multiple of 2 limitation.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Uses the new multi-ring infrastucture.  6xx/7xx has a single
async DMA ring.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NDave Airlie <airlied@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDave Jones <davej@redhat.com>

Let's allow GCC to optimize better.

This exposed some five unused functions, but this patch doesn't remove them.
Signed-off-by: NLauri Kasanen <cand@gmx.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This check the root ports supported link speeds and enables
GEN2 mode if the 5.0 GT link speed is available.

The first 3.0 cards are SI so they will probably need more investigation.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Before emitting any indirect buffer, emit the offset of the next
valid ring content if any. This allow code that want to resume
ring to resume ring right after ib that caused GPU lockup.

v2: use scratch registers instead of storing it into memory
v3: skip over the surface sync for ni and si as well
v4: use SET_CONFIG_REG instead of PACKET0
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NChristian König <deathsimple@vodafone.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Making it easier to control when it is executed.
Signed-off-by: NChristian König <deathsimple@vodafone.de>
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

Just reinitialize the shader content on resume instead.
Signed-off-by: NChristian König <deathsimple@vodafone.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

The IB pool is in gart memory, so it is completely
superfluous to unpin / repin it on suspend / resume.
Signed-off-by: NChristian König <deathsimple@vodafone.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

For a normal suspend/resume we allready wait for
the rings to be empty, and for a suspend/reasume
in case of a lockup we REALLY don't want to wait
for anything.
Signed-off-by: NChristian König <deathsimple@vodafone.de>
Reviewed-by: NJerome Glisse <jglisse@redhat.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>

- SMX_SAR_CTL0 needs to be programmed correctly to prevent
problems with memory exports in certain cases.
- VC_ENHANCE needs to be initialized on 6xx/7xx.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Call it in the asic startup callback on all asics.
Previously r600 and rv770 called it in the startup
and resume callbacks while all the other asics called
it in the startup callback.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Tiling group size is always 256bits on r6xx/r7xx/r8xx/9xx. Also fix and
simplify render backend map. This now properly sets up the backend map
on r6xx-9xx which should improve 3D performance.

Vadim benchmarked also:
Some benchmarks on juniper (5750), fullscreen 1920x1080,
first result - kernel 3.4.0+ (fb21affa), second - with these patches:

Lightsmark:   91 fps => 123 fps    +35%
Doom3:        74 fps => 101 fps    +36%
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>