Signed-off-by: NAndrew Jeffery <andrew@aj.id.au>
Acked-by: NJoel Stanley <joel@jms.id.au>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The recent addition of the regulator support has led to the pca953x_remove
function returning uninitialized data when no platform data pointer is
provided, as gcc warns when using -Wmaybe-uninitialized:

drivers/gpio/gpio-pca953x.c: In function 'pca953x_remove':
drivers/gpio/gpio-pca953x.c:860:9: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]

This restores the previous behavior, returning 0 on success.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: e23efa31 ("gpio: pca954x: Add vcc regulator and enable it")
Acked-by: NPhil Reid <preid@electromag.com.au>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add binding for TPIC2810 GPO device.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_VF610
drivers/gpio/Kconfig:   def_bool y

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

We delete the MODULE_LICENSE tag etc. since all that information
is now contained at the top of the file in the comments.

We don't replace module.h with init.h since the file already has that.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_SPEAR_SPICS
drivers/gpio/Kconfig:   bool "ST SPEAr13xx SPI Chip Select as GPIO support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

We delete the MODULE_LICENSE tag etc. since all that information
is now contained at the top of the file in the comments.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_MXC
drivers/gpio/Kconfig:   def_bool y

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

We delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Note the original e-mail had a missing/typo'd @ symbol anyway.

We don't replace module.h with init.h since the file already has that.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Juergen Beisert <kernel@pengutronix.de>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_MSIC
drivers/gpio/Kconfig:   bool "Intel MSIC mixed signal gpio support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

We don't replace module.h with init.h since the file already has that.

Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds .get_direction method for the gpio_chip structure
of the wcove_gpio driver.
Signed-off-by: NBin Gao <bin.gao@intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This driver is generic and aims to support all Technologic Systems's
boards embedding FPGA GPIOs with an I2C interface.

This driver supports TS-4900, TS-7970, TS-7990 and TS-4100 series.
Signed-off-by: NLucile Quirion <lucile.quirion@savoirfairelinux.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Device tree binding documentation for Technologic's I2C-FPGA GPIO
controller.
Signed-off-by: NLucile Quirion <lucile.quirion@savoirfairelinux.com>
[Quirked in a reference to gpio.txt]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This binding is no longer correct, the GPIO information can should be
added to the parent node and not into this child node. See
Documentation/devicetree/bindings/mfd/tps65086.txt for the correct usage.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The if...else... block after the loop can be dropped with
a slight refactoring.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds support for the GPIO found in Broadcom's bcm63xx-gpio
chips.
This GPIO controller is used in the following Broadcom SoCs: BCM6338, BCM6345.
It can be used in newer SoCs, without the capability of pin multiplexing.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NÁlvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds the device tree bindings for the Broadcom's BCM6345
memory-mapped GPIO controllers.

The gpios will be supported by gpio-mmio code of the
GPIO generic library.
Signed-off-by: NÁlvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Immutable branch between MFD and GPIO due for the v4.9 merge window

The Diamond Systems GPIO-MM device features 48 lines of digital I/O via
the emulation of dual 82C55A PPI chips. This driver provides GPIO
support for these 48 channels of digital I/O. The base port addresses
for the devices may be configured via the base array module parameter.
Signed-off-by: NWilliam Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch introduces a separate GPIO driver for Intel WhiskeyCove PMIC.
This driver is based on gpio-crystalcove.c.

Changes in v7:
 - Fixed various coding style comments from Andy Shevchenko
Changes in v6:
 - Removed unnecessary wcove_gpio_remove()
 - Used devm_gpiochip_remove() instead of gpiochip_remove()
 - Various coding style changes per Mika's comment
Changes in v5:
 - Revisited the interrupt handler code to iterate until all pending
   interrupts are handled. This change is to avoid missing interrupt
   when we're inside the interrupt handler.
 - Used regmap_bulk_read() to read address adjacent registers.
Changes in v4:
 - Converted CTLI_INTCNT_XX macros to less verbose ones INT_DETECT_XX.
 - Add comments about why there is no .pm for the driver.
 - Header files re-ordered.
 - Various coding style change to address Andy's comments.
Changes in v3:
 - Fixed the year in copyright line(2015-->2016).
 - Removed DRV_NAME macro.
 - Added kernel-doc for regmap_irq_chip of the wcove_gpio structure.
 - Line length fix.
Changes in v2:
 - Typo fix (Whsikey --> Whiskey).
 - Included linux/gpio/driver.h instead of linux/gpio.h
 - Implemented .set_single_ended().
 - Added GPIO register description.
 - Replaced container_of() with gpiochip_get_data().
 - Removed unnecessary "if (gpio > WCOVE_VGPIO_NUM" check.
 - Removed the device id table and added MODULE_ALIAS().
Signed-off-by: NAjay Thomas <ajay.thomas.david.rajamanickam@intel.com>
Signed-off-by: NBin Gao <bin.gao@intel.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The AXP209 PMIC has a bunch of GPIOs accessible, that are usually used to
control LEDs or backlight.

Add a driver for them
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Some i2c gpio devices are connected to a switchable power supply
which needs to be enabled prior to probing the device. This patch
allows the drive to enable the devices vcc regulator prior to probing.
Signed-off-by: NPhil Reid <preid@electromag.com.au>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The particularities of this variant are:
- GPIO_XXX_LSB and GPIO_XXX_MSB memory locations are inverted compared
  to other variants.
- There is no Edge detection, Rising Edge and Falling Edge registers.
- IRQ flags are cleared when read, no need to write in Status register.
Signed-off-by: NAmelie DELAUNAY <amelie.delaunay@st.com>
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

STMPE1600 is a 16-bit port expander.
Datasheet is available here :
http://www2.st.com/content/st_com/en/products/interfaces-and-transceivers/
i-o-expanders-and-level-translators/i-o-expanders/stmpe1600.html
Signed-off-by: NAmelie DELAUNAY <amelie.delaunay@st.com>
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds a new compatible string for stmpe mfd to support
stmpe1600 variant.
Signed-off-by: NAmelie DELAUNAY <amelie.delaunay@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This update allows to use registers map as following :
regs[reg_index + offset] instead of
regs[reg_index] + offset

This makes code clearer and will facilitate the addition of STMPE1600
on which LSB and MSB registers are respectively located at addr and addr + 1.
Despite for all others STMPE variant, LSB and MSB registers are respectively
located in reverse order at addr + 1 and addr.

For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes
which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH)
register addresses (STMPE1801/STMPE24xx).
For variant which have 2 registers's bank, we use LSB and CSB indexes only.
In this case the CSB index contains the MSB regs address (STMPE 1601).
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

this update allows to use registers map as following :
regs[reg_index + offset] instead of
regs[reg_index] + offset

This makes code clearer and will facilitate the addition of STMPE1600
on which LSB and MSB registers are respectively located at addr and addr + 1.
Despite for all others STMPE variant, LSB and MSB registers are respectively
located in reverse order at addr + 1 and addr.

For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes
which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH)
register addresses (STMPE1801/STMPE24xx).
For variant which have 2 registers's bank, we use LSB and CSB indexes only.
In this case the CSB index contains the MSB regs address (STMPE 1601).
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

In order to prepare the ground to STMPE1600,
as STMPE1600's SYS_CTRL register has the same layout as
STMPE801 variant, unify STMPExxx_REG_SYS_CTRL_RESET/INT_EN/INT_HI
bit masks to more generic STMPE_SYS_CTRL_RESET/INT_EN/INT_HI
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

On STMPE801/1801 datasheets, it's mentionned writing
in interrupt status register has no effect, bits are
cleared when reading.
Signed-off-by: NAmelie DELAUNAY <amelie.delaunay@st.com>
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

By cross-checking STMPE 610/801/811/1601/2401/2403 datasheets,
it appears that edge detection and rising/falling edge detection
is not supported by all STMPE variant:

           GPIO              GPIO
      Edge detection     rising/falling
                         edge detection
 610 |      X        |         X       |
 801 |               |                 |
 811 |      X        |         X       |
1600 |               |                 |
1601 |      X        |         X       |
1801 |               |         X       |
2401 |      X        |         X       |
2403 |      X        |         X       |

Rework stmpe_dbg_show_one() and stmpe_gpio_irq to correctly
take these cases into account.
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Reset was only implemented for STMPE1801 variant despite
all variant have a SOFT_RESET bit.

For STMPE2401/2403/801/1601/1801 SOFT_RESET bit is bit 7
of SYS_CTRL register.
For STMPE610/811 (which have the same variant id) SOFT_RESET
bit is bit 1 of SYS_CTRL register.
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As STMPE1801/1601/24xx has a SYS_CTRL register and
STMPE1601/2403 has even a SYS_CTRL2 register, add
STMPE_IDX_SYS_CTRL/2 and update driver code accordingly

This update prepares the ground for not yet supported STMPE1600
which share similar REG_SYS_CTRL register.
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The GPIOLIB is now selectable explicitly, and always available
for all archs. All archs that require GPIOLIB are switched to
select GPIOLIB directly. Delete the hairy ARCH_REQUIRE_GPIOLIB
and ARCH_WANTS_OPTIONAL_GPIOLIB Kconfig symbols.

Cc: Michael Büsch <m@bues.ch>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

A new user of the Kconfig selection of ARCH_REQUIRE_GPIOLIB
has appeared. Replace with just selecting GPIOLIB.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Replace "select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB"
as this can now be selected directly.

Cc: Michael Büsch <m@bues.ch>
Cc: Steven Miao <realmz6@gmail.com>
Cc: adi-buildroot-devel@lists.sourceforge.net
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This replaces:

- "select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB" as this can
  now be selected directly.

- "select ARCH_WANT_OPTIONAL_GPIOLIB" with no dependency: GPIOLIB
  is now selectable by everyone, so we need not declare our
  intent to select it.

Cc: Michael Büsch <m@bues.ch>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Pull more block fixes from Jens Axboe:
 "As mentioned in the pull the other day, a few more fixes for this
  round, all related to the bio op changes in this series.

  Two fixes, and then a cleanup, renaming bio->bi_rw to bio->bi_opf.  I
  wanted to do that change right after or right before -rc1, so that
  risk of conflict was reduced.  I just rebased the series on top of
  current master, and no new ->bi_rw usage has snuck in"

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: rename bio bi_rw to bi_opf
  target: iblock_execute_sync_cache() should use bio_set_op_attrs()
  mm: make __swap_writepage() use bio_set_op_attrs()
  block/mm: make bdev_ops->rw_page() take a bool for read/write

Pull drm zpos property support from Dave Airlie:
 "This tree was waiting on some media stuff I hadn't had time to get a
  stable branchpoint off, so I just waited until it was all in your tree
  first.

  It's been around a bit on the list and shouldn't affect anything
  outside adding the generic API and moving some ARM drivers to using
  it"

* tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux:
  drm: rcar: use generic code for managing zpos plane property
  drm/exynos: use generic code for managing zpos plane property
  drm: sti: use generic zpos for plane
  drm: add generic zpos property

Since commit 63a4cc24, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.

No intended functional changes in this commit.
Signed-off-by: NJens Axboe <axboe@fb.com>

The original commit missed this function, it needs to mark it a
write flush.

Cc: Mike Christie <mchristi@redhat.com>
Fixes: e742fc32 ("target: use bio op accessors")
Signed-off-by: NJens Axboe <axboe@fb.com>

Cleaner than manipulating bio->bi_rw flags directly.
Signed-off-by: NJens Axboe <axboe@fb.com>

Commit abf54548 changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.

Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: NMike Christie <mchristi@redhat.com>
Signed-off-by: NJens Axboe <axboe@fb.com>