Commit 7c7b60cb
"of: put default string compare and #a/s-cell values into common header"

Breaks various things on powerpc due to using strncasecmp instead of
strcasecmp for comparing against "compatible" strings.

This causes things like the 4xx PCI code to fail miserably due to the
partial matches in code like this:

       for_each_compatible_node(np, NULL, "ibm,plb-pcix")
               ppc4xx_probe_pcix_bridge(np);
       for_each_compatible_node(np, NULL, "ibm,plb-pci")
               ppc4xx_probe_pci_bridge(np);

It's not quite right to do partial name match. Entries in a compatible
list are meant to be matched whole. If a device is compatible with both
"foo" and "foo1", then the device should have both strings in its
"compatible" property.

This patch reverts powerpc and microblaze us to use strcasecmp.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
      (for patch description)
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NMichal Simek <michal.simek@petalogix.com>

Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

omap2_mcspi_transfer() gets called in omap2_mcspi_work() when the
transaction speed_hz or bits_per_word fields are non-zero.

omap2_mcspi_transfer() does not look at the speed_hz field so
the override speed value is ignored.

The code should probably change to one of these options.

1. Skip the call to omap2_mcsp_transfer() if the only reason was a
non-zero speed_hz and it's not going to be used.

2. Use the new speed_hz value provided

The patch below uses the speed_hz value.
Signed-off-by: NScott Ellis <scott@jumpnowtek.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Check spi->controller_state before dereferencing.

Shows up NULL here when using spi_alloc_device()/spi_add_device()
and spi_add_device() fails before spi_setup(). Calling spi_dev_put()
on the leftover spi_device results in the error.
Signed-off-by: NScott Ellis <scott@jumpnowtek.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

We can get this driver enabled via MFD_TIMBERDALE which only
requires GPIO to be on.

But the of_address_to_resource() function is only present on
powerpc and microblaze, so we have to conditionalize the
CONFIG_OF probing bits on that.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (62 commits)
  msi-laptop: depends on RFKILL
  msi-laptop: Detect 3G device exists by standard ec command
  msi-laptop: Add resume method for set the SCM load again
  msi-laptop: Support some MSI 3G netbook that is need load SCM
  msi-laptop: Add threeg sysfs file for support query 3G state by standard 66/62 ec command
  msi-laptop: Support standard ec 66/62 command on MSI notebook and nebook
  Driver core: create lock/unlock functions for struct device
  sysfs: fix for thinko with sysfs_bin_attr_init()
  sysfs: Kill unused sysfs_sb variable.
  sysfs: Pass super_block to sysfs_get_inode
  driver core: Use sysfs_rename_link in device_rename
  sysfs: Implement sysfs_rename_link
  sysfs: Pack sysfs_dirent more tightly.
  sysfs: Serialize updates to the vfs inode
  sysfs: windfarm: init sysfs attributes
  sysfs: Use sysfs_attr_init and sysfs_bin_attr_init on module dynamic attributes
  sysfs: Document sysfs_attr_init and sysfs_bin_attr_init
  sysfs: Use sysfs_attr_init and sysfs_bin_attr_init on dynamic attributes
  sysfs: Use one lockdep class per sysfs attribute.
  sysfs: Only take active references on attributes.
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] i6300esb.c: change platform_driver to pci_driver
  [WATCHDOG] i6300esb: fix unlock register with
  [WATCHDOG] drivers/watchdog/wdt.c:wdt_ioctl(): make `ident' non-static
  [WATCHDOG] change reboot_notifier to platform-shutdown method.
  [WATCHDOG] watchdog_info constify
  [WATCHDOG] gef_wdt: Author corrections following split of GE Fanuc joint venture
  [WATCHDOG] iTCO_wdt: clean up probe(), modify err msg
  [WATCHDOG] ep93xx: watchdog timer driver for TS-72xx SBCs cleanup
  [WATCHDOG] support for max63xx watchdog timer chips
  [WATCHDOG] ep93xx: added platform side support for TS-72xx WDT driver
  [WATCHDOG] ep93xx: implemented watchdog timer driver for TS-72xx SBCs

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (26 commits)
  ALSA: hdmi - show debug message on changing audio infoframe
  ALSA: hdmi - merge common code for intelhdmi and nvhdmi
  ALSA: hda - Add ASRock mobo to MSI blacklist
  ALSA: hda: uninitialized variable fix
  ALSA: hda: Use LPIB for a Biostar Microtech board
  ALSA: usb/audio.h: Fix field order
  ALSA: fix jazz16 compile (udelay)
  ALSA: hda: Use LPIB for Dell Latitude 131L
  ALSA: hda - Build hda_eld into snd-hda-codec module
  ALSA: hda - Support NVIDIA MCP89 and GT21x hdmi audio
  ALSA: hda - Support max codecs to 8 for nvidia hda controller
  ALSA: riptide: clean up while loop
  ALSA: usbaudio - remove debug "SAMPLE BYTES" printk line
  ALSA: timer - pass real event in snd_timer_notify1() to instance callback
  ALSA: oxygen: change || to &&
  ALSA: opti92x: use PnP data to select Master Control port
  ASoC: fix ak4104 register array access
  ASoC: soc_pcm_open: Add missing bailout tag
  ALSA: usbaudio: Fix wrong bitrate for Creative Creative VF0470 Live Cam
  ALSA: ua101: removing debugging code
  ...

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] smsgiucv_app: deliver z/VM CP special messages (SMSG) as uevents
  [S390] smsgiucv: declare char pointers as "const"
  [S390] dasd: automatic recognition of read-only devices
  [S390] remove unused qdio flags in zfcp and qeth
  [S390] Cleanup xtime usage
  [S390] qdio: add missing bracket
  [S390] cio: fix init_count in case of recognition after steal lock
  [S390] dasd: security and PSF update patch for EMC CKD ioctl
  [S390] hvc_iucv: allocate memory buffers for IUCV in zone DMA
  [S390] uaccess: make sure copy_from_user_overflow is builtin

Remove the EXPERIMENTAL flag from FS-Cache so that Ubuntu can make use of the
facility.
Signed-off-by: NChristian Kujau <lists@nerdbynature.de>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since the intel 6300esb platform uses a dedicated PCI ID for
it's watchdog timer (00:1d.4), it's better and easier to have
this as a pci_driver.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

The smsgiucv_app driver registers a callback with the smsgiucv driver
to receive z/VM CP special messages (SMSG) starting with "APP".

When the callback is called for special messages, the driver creates
an uevent for the received message.  The uevent consists of additional
environment data containing the message prefix ("APP"), message sender,
and message content.

udev rules can be used to trigger application specific actions through
matching the content or sender of the special message.
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Declare the smsgiucv prefix char pointer as "const" and use
use const char pointers in callback functions.
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

In z/VM it is possible to attach a device as read-only. To prevent
unintentional write requests and subsequent I/O errors, we can detect
this configuration using the z/VM DIAG 210 interface and set the
respective linux block device to read-only as well.
Signed-off-by: NStefan Weinhuber <wein@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

zfcp and qeth are setting flags for the qdio-layer, but these flags
are not used in qdio. Patch removes the flag definitions from qdio
and their settings in zfcp and qeth.

Cc: Jan Glauber <jang@linux.vnet.ibm.com>
Cc: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This replaces direct xtime usage in the s390 arch with timekeeping accessors,
so we can further clean up the timekeeping core.

Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add a missing bracket to only log the outbound handler event in the
appropriate case.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

After we try to steal a lock on a ccw device in boxed state,
we have to restart device recognition and potentially reprobing.

In this case ccw_device_init_count was erroneously decreased
twice. This patch fixes the issue.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Remove the PSF order/suborder check from the Symmetrix CKD dasd ioctl.
In exchange restrict the ioctl to CAP_SYS_ADMIN and CAP_SYS_RAWIO.
Signed-off-by: NNigel Hislop <hislop_nigel@emc.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The device driver must allocate memory for IUCV buffers with GFP_DMA,
because IUCV cannot address memory above 2GB (31bit addresses only).

Because the IUCV ignores the higher bits of the address, sending and
receiving IUCV data with this driver might cause memory corruptions.
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

If there is no in kernel image caller modules will suffer:

ERROR: "copy_from_user_overflow" [net/core/pktgen.ko] undefined!
ERROR: "copy_from_user_overflow" [net/can/can-raw.ko] undefined!
ERROR: "copy_from_user_overflow" [fs/cifs/cifs.ko] undefined!
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Before you can read or write from the i6300esb memeory mapped registers,
you need to unlock these. This is done by writing the magic numbers 0x80
and 0x86 to the reload register. The size of the reload register is 32bit
though.

Also binary 11 is hex 0x03 and not 0x11.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Also change printk level for the two others.
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Create patch_hdmi.c to hold common code from intelhdmi and nvhdmi.

For now the patch_hdmi.c file is simply included by patch_intelhdmi.c
and patch_nvhdmi.c, and does not represent a real codec.

There are no behavior changes to intelhdmi. However nvhdmi made several
changes when copying code out of intelhdmi, which are all reverted in
this patch. Wei Ni confirmed that the reverted code actually works fine.
Tested-by: NWei Ni <wni@nvidia.com>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

msi-laptop uses rfkill*() interfaces so it should depend on RFKILL.

msi-laptop.c:(.text+0x1fcd1b): undefined reference to `rfkill_alloc'
msi-laptop.c:(.text+0x1fcd76): undefined reference to `rfkill_register'
msi-laptop.c:(.text+0x1fcdc8): undefined reference to `rfkill_destroy'
msi-laptop.c:(.text+0x1fcdd9): undefined reference to `rfkill_unregister'

This repairs "msi-laptop: Detect 3G device exists by standard ec command",
which is in some gregkh tree.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Detect 3G device exists by standard ec command. Driver will not create the threeg sysfs
file and threeg rfkill interface if there have no internal 3G device in MSI notebook/netbook.
Signed-off-by: NLee, Chun-Yi <jlee@novell.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Implement the resume method for set the load SCM flag after system reusme.
Without this patch, the wifi function key on SCM model will back to BIOS
control mode then confuse with the userland software control.
e.g. MSI N034
Signed-off-by: NLee, Chun-Yi <jlee@novell.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some MSI 3G netbook only have one fn key to control Wlan/Bluetooth/3G,
those netbook will load the SCM (windows app) to disable the original
Wlan/Bluetooth control by BIOS when user press fn key, then control
Wlan/Bluetooth/3G by SCM (software control by OS). Without SCM, user
cann't on/off 3G module on those 3G netbook.
On Linux, msi-laptop driver will do the same thing to disable the
original BIOS control, then might need use HAL or other userland
application to do the software control that simulate with SCM.
e.g. MSI N034 netbook
Signed-off-by: NLee, Chun-Yi <jlee@novell.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add threeg sysfs file for support query 3G state by standard 66/62 ec
command, the MSI standard ec interface supported this feature.
Signed-off-by: NLee, Chun-Yi <jlee@novell.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Suppport standard ec 66/62 command on MSI notebook and nebook. MSI
netbook and notebook already support 66/62 command, so, add new
get_state function, and put the old model to non-standard model, but
driver still support those old model.
Signed-off-by: NLee, Chun-Yi <jlee@novell.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In the future, we are going to be changing the lock type for struct
device (once we get the lockdep infrastructure properly worked out)  To
make that changeover easier, and to possibly burry the lock in a
different part of struct device, let's create some functions to lock and
unlock a device so that no out-of-core code needs to be changed in the
future.

This patch creates the device_lock/unlock/trylock() functions, and
converts all in-tree users to them.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Cc: Magnus Damm <damm@igel.co.jp>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Alex Chiang <achiang@hp.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Yu Zhao <yu.zhao@intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: CHENG Renquan <rqcheng@smu.edu.sg>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Frans Pop <elendil@planet.nl>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

After merging the final tree, today's linux-next build (powerpc
allyesconfig) failed like this:

drivers/pci/pci-sysfs.c: In function 'pci_create_legacy_files':
drivers/pci/pci-sysfs.c:645: error: lvalue required as unary '&' operand
drivers/pci/pci-sysfs.c:658: error: lvalue required as unary '&' operand

Caused by commit "sysfs: Use sysfs_attr_init and sysfs_bin_attr_init on
dynamic attributes" interacting with commit "sysfs: Use one lockdep
class per sysfs attribute") both from the driver-core tree.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now that there are no more users we can remove
the sysfs_sb variable.
Acked-by: NTejun Heo <tj@kernel.org>
Acked-by: NSerge Hallyn <serue@us.ibm.com>
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently sysfs_get_inode magically returns an inode on
sysfs_sb.  Make the super_block parameter explicit and
the code becomes clearer.
Acked-by: NTejun Heo <tj@kernel.org>
Acked-by: NSerge Hallyn <serue@us.ibm.com>
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Don't open code the renaming of symlinks in sysfs
instead use the new helper function sysfs_rename_link
Acked-by: NTejun Heo <tj@kernel.org>
Acked-by: NSerge Hallyn <serue@us.ibm.com>
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Because of rename ordering problems we occassionally give false
warnings about invalid sysfs operations.  So using sysfs_rename
create a sysfs_rename_link function that doesn't need strange
workarounds.

Cc: Benjamin Thery <benjamin.thery@bull.net>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: NSerge Hallyn <serue@us.ibm.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>