This patch makes the pinctrl-samsung driver configure GPIO direction on
its own, without using the pinctrl_gpio_direction_*() "helpers". The
rationale behind this change is as follows:
 - pinctrl-samsung does not need translation from GPIO namespace to
   pinctrl namespace to handle GPIO operations - GPIO chip and offset
   therein are enough to calculate necessary offsets and bit masks in
   constant time,
 - the pinctrl_gpio_direction_*() functions do not do anything useful
   other than translating the pin into pinctrl namespace and calling the
   .gpio_set_direction() from pinmux_ops of the controller,
 - the undesirable side effect of using those helpers is losing the
   ability to change GPIO direction in atomic context, because they
   explicitly use a mutex for synchronization,

Results of this patch are:
 - fixed warnings about scheduling while atomic in code that needs to
   set GPIO direction in atomic context (e.g. interrupt handler),
 - reduced overhead of bitbanging drivers that use gpio_direction_*(),
   e.g. i2c-gpio.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add CAN0/1 data/clock pin groups to R8A7791 PFC driver.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

For Baytrail, you should never set a GPIO set to direct_irq
to output mode.  When direct_irq_en is set for a GPIO, it is
tied directly to an APIC internally, and making the pad output
does not make any sense. Assert a WARN() in the event this happens.
Signed-off-by: NEric Ernst <eric.ernst@linux.intel.com>
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Remove variable that are never used

This was found using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

%d in format string used, but the type is unsigned int

This was found using a static code analysis program called cppcheck
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

%d in format string used, but the type is unsigned int

This was found using a static code analysis program called cppcheck
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Remove variable that are never used

This was found using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Remove variable that are never used

This was found using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Remove checking if a unsigned is less than zero

This was found using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Remove checking if a unsigned is less than zero

This was found using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Remove checking if a unsigned is less than zero

This was found using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Remove checking if a unsigned is less than zero

This was found using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

no .irq_set_wake API is available for pinctrl-st driver.
Add the IRQCHIP_SKIP_SET_WAKE flag to inform irq handler
not to call this API.
Signed-off-by: NDavid Paris <david.paris@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

bcm281xx_pinctrl_probe is local to this file. Make it static.
Signed-off-by: NSachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds the BUS_HOLD (Keeper) bias option for pins.
Signed-off-by: NAndy Gross <agross@codeaurora.org>
Acked-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The A23 has a R_PIO pin controller, similar to the one found on the A31 SoC.
Add support for the pins controlled by the R_PIO controller.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The A23 uses the same pin controller as previous SoC's from Allwinner.
Add support for the pins controlled by the main PIO controller.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The PINCTRL_SUNXI configuration was kept only to deal with the introduction of
per-machine symbols and the various pintrl drivers through different tree.

Now that it's not useful anymore, we can just remove it.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The A13 user manual states pins PG0/1/2 only have GPIO input and
interrupt functions. Remove the gpio_out functions for these pins.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The pin-controller of the new RK3288 contains all the quirks just added in
the previous patches.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

On the upcoming RK3288 SoC contain some unrouted pins in their banks. So while
for example pin8 of bank5 stays pin8 with all its settings (register offset etc),
pins 0 to 7 are not routed outside the SoC at all.
Therefore add a flag to mark these unrouted iomuxes to prevent people from using
them.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The upcoming rk3288 moves some iomux settings to the pmu register space.
Therefore add a flag for this and adapt the mux functions accordingly.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

In the upcoming rk3288 SoC some iomux settings are 4bit wide instead of
the regular 2bit. Therefore add a flag to mark iomuxes as such and adapt
the mux-access as well as the offset calculation accordingly.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

An upcoming SoC introduces an interesting quirk to iomux handling making the
calculation of the iomux register-offset harder. To keep the complexity down
when getting/setting the mux, precalculate the actual register offset at
probe-time.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Upcoming Rockchip SoCs have additional quirks to handle. Currently they would
be handled by giving the bank a special compatible property. But the nature
of the new quirks would require a lot of them. Also as we want to move to the
separate dw_gpio driver in the future, these bank-definitions should be
extended at all.

Describing the bank quirks this way also enables us to deprecate the special
bank compatible string for bank0 on rk3188 and simplify the handling code.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

What the patch does:
1. Call pinmux_disable_setting ahead of pinmux_enable_setting
  each time pinctrl_select_state is called
2. Remove the HW disable operation in pinmux_disable_setting function.
3. Remove the disable ops in struct pinmux_ops
4. Remove all the disable ops users in current code base.

Notes:
1. Great thanks for the suggestion from Linus, Tony Lindgren and
   Stephen Warren and Everyone that shared comments on this patch.
2. The patch also includes comment fixes from Stephen Warren.

The reason why we do this:
1. To avoid duplicated calling of the enable_setting operation
   without disabling operation inbetween which will let the pin
   descriptor desc->mux_usecount increase monotonously.
2. The HW pin disable operation is not useful for any of the
   existing platforms.
   And this can be used to avoid the HW glitch after using the
   item #1 modification.

In the following case, the issue can be reproduced:
1. There is a driver that need to switch pin state dynamically,
   e.g. between "sleep" and "default" state
2. The pin setting configuration in a DTS node may be like this:

  component a {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&a_grp_setting &c_grp_setting>;
	pinctrl-1 = <&b_grp_setting &c_grp_setting>;
  }

  The "c_grp_setting" config node is totally identical, maybe like
  following one:

  c_grp_setting: c_grp_setting {
	pinctrl-single,pins = <GPIO48 AF6>;
  }

3. When switching the pin state in the following official pinctrl
   sequence:
	pin = pinctrl_get();
	state = pinctrl_lookup_state(wanted_state);
	pinctrl_select_state(state);
	pinctrl_put();

Test Result:
1. The switch is completed as expected, that is: the device's
   pin configuration is changed according to the description in the
   "wanted_state" group setting
2. The "desc->mux_usecount" of the corresponding pins in "c_group"
   is increased without being decreased, because the "desc" is for
   each physical pin while the setting is for each setting node
   in the DTS.
   Thus, if the "c_grp_setting" in pinctrl-0 is not disabled ahead
   of enabling "c_grp_setting" in pinctrl-1, the desc->mux_usecount
   will keep increasing without any chance to be decreased.

According to the comments in the original code, only the setting,
in old state but not in new state, will be "disabled" (calling
pinmux_disable_setting), which is correct logic but not intact. We
still need consider case that the setting is in both old state
and new state. We can do this in the following two ways:

1. Avoid to "enable"(calling pinmux_enable_setting) the "same pin
   setting" repeatedly
2. "Disable"(calling pinmux_disable_setting) the "same pin setting",
   actually two setting instances, ahead of enabling them.

Analysis:
1. The solution #2 is better because it can avoid too much
   iteration.
2. If we disable all of the settings in the old state and one of
   the setting(s) exist in the new state, the pins mux function
   change may happen when some SoC vendors defined the
   "pinctrl-single,function-off"
   in their DTS file.
   old_setting => disabled_setting => new_setting.
3. In the pinmux framework, when a pin state is switched, the
   setting in the old state should be marked as "disabled".

Conclusion:
1. To Remove the HW disabling operation to above the glitch mentioned
   above.
2. Handle the issue mentioned above by disabling all of the settings
   in old state and then enable the all of the settings in new state.
Signed-off-by: NFan Wu <fwu@marvell.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NPatrice Chotard <patrice.chotard@st.com>
Acked-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Pads for PB0-PB3, PC0-PC4, PE26-PE31 and PF24-PF31 does not exist on
the i.MX27 SOC. There is no reason to define them, the presence of
such definitions in the DTS files is a bug.
This patch removes these nonexistent pad definitions.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

struct imx27_pinctrl_private is not used in the driver.
Remove this definition.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds pincontrol driver for Freescale i.MX1 SOCs.
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When mapping the interrupts, the gpio_to_irq function did not consider
the bank number of the gpio pin in question, only the offset or the
interrupt number in the bank. As a result, requests for interrupts in
the later banks get mapped to the first bank.

This issue was discovered while enabling mmc on the new sun8i platform.
The tablet I have uses a pin/interrupt from the second bank to do mmc
card detection. Tested on this very device with register inspection and
actual mmc card insertion/removal.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Some drivers use disable_irq / enable_irq and do the work
clearing the source in another thread instead of using a threaded
interrupt handler.

The irqchip used not having irq_disable and irq_enable
callbacks in this case, will lead to unnecessary spurious
interrupts:

On a disable_irq in a chip without a handler for this, the irq
core will remember the disable, but not actually call into the
irqchip. With a level triggered interrupt (where the source has
not been cleared) this will lead to an immediate retrigger, at
which point the irq-core will mask the irq. So having an
irq_disable callback in the irqchip will save us the interrupt
firing a 2nd time for nothing.

Drivers using disable / enable_irq like this, will call
enable_irq when they finally have cleared the interrupt source,
without an enable_irq callback, this will turn into an unmask,
at which point the irq will trigger immediately because when it
was originally acked the level was still high, so the ack was
a nop.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

For level triggered gpio interrupts we need to use handle_fasteoi_irq,
like we do with the irq-sunxi-nmi driver. This is necessary to give threaded
interrupt handlers a chance to actuall clear the source of the interrupt
(which may involve sleeping waiting for i2c / spi / mmc transfers), before
acknowledging the interrupt.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

With level triggered interrupt mask / unmask will get called for each
interrupt, doing the somewhat expensive mux setting on each unmask thus is
not a good idea. Instead add a request_resources callback and do it there.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The sunxi pinctrl irq chip driver does not support wakeup at the
moment. Adding IRQCHIP_SKIP_SET_WAKE lets the irqs work with drivers
using wakeup.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

These symbols are supposed to be selected by the drivers actually needing
them. The only situation where it would make sense to enable them without a
driver selecting them is when an out-of-tree pinctrl driver is used or
for compile testing.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This switches the SPEAr PLGPIO driver over to using the irqchip
helpers.

As part of this effort, also get rid of the strange irq_base
calculation and failure to use d->hwirq for obtaining a local
irqchip offset.

Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: spear-devel@list.st.com
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The A23 and A31 support multiple interrupt banks. Support it by adding a linear
domain covering all the banks. It's trickier than it should because there's an
interrupt per bank, so we have multiple interrupts using the same domain.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The primary pinctrl device has 4 interrupt banks. As usual, to be able to
generate interrupts, the pins supporting it need to be muxed to a special
function. Declare these functions in the pins array.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Declare in the description structure associated to the compatible the number of
interrupt banks the device has. For now, we're not doing anything with it.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>