The timerfd was using the unlocked waitqueue operations, but it was
using a different lock, so poll_wait() would race with it.

This makes timerfd directly use the waitqueue lock.
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The eventfd was using the unlocked waitqueue operations, but it was
using a different lock, so poll_wait() would race with it.

This makes eventfd directly use the waitqueue lock.
Signed-off-by: NDavide Libenzi <davidel@xmailserver.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (32 commits)
  [POWERPC] Remove build warnings in windfarm_core
  [POWERPC] Pass per-file CFLAGs for platform specific op codes
  [POWERPC] Correct #endif comment
  [POWERPC] Fix ppc_rtas_progress_show()
  [POWERPC] Fix sed command lines for zlib source construction
  [POWERPC] Specify GNUTARGET on $(AR) invocations
  [POWERPC] Make sure device node type/name is not NULL on hot-added nodes
  [POWERPC] Small fixes for the Ebony device tree
  [POWERPC] Fix warning on UP
  [POWERPC] cell_defconfig: Disable cpufreq and pmi
  [POWERPC] Fix IO space on PCI buses created from of_platform
  [POWERPC] Add spinlock to request_phb_iospace()
  [POWERPC] Fix make rules for treeImage.initrd
  [POWERPC] Remove warning in mpic.c
  [POWERPC] Update pasemi_defconfig
  [POWERPC] pasemi: CONFIG_GENERIC_TBSYNC no longer needed
  [POWERPC] Update iseries_defconfig
  [POWERPC] Wire up some more syscalls
  [POWERPC] Fix bug adding properties with flatdevtree.c's ft_set_prop()
  [POWERPC] Remove fixup_bigphys_addr() for arch/powerpc to avoid link error
  ...

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Fix sched_clock() et al.

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [IPV4]: Remove IPVS icmp hack from route.c for now.
  [IPV4]: Correct rp_filter help text.
  [TCP]: TCP_CONG_YEAH requires TCP_CONG_VEGAS
  [TCP] slow start: Make comments and code logic clearer.
  [BLUETOOTH]: Fix locking in hci_sock_dev_event().
  [NET]: Fix BMSR_100{HALF,FULL}2 defines in linux/mii.h
  [NET]: lockdep classes in register_netdevice

The slab manipulation functions should not be triggered by slabs that
are unresovable in the subset of slabs selected on the command line.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As pointed out by Jarek Poplawski, the patch

	[WORKQUEUE]: cancel_delayed_work: use del_timer() instead of del_timer_sync()
	commit: 071b6386

was wrong, it was merged by mistake after that.

From the changelog:

	after this patch:
		...
		delayed_work_timer_fn->__queue_work() in progress.

		The latter doesn't differ from the caller's POV,

it does make a difference if the caller calls flush_workqueue() after
cancel_delayed_work(), in that case flush_workqueue() can miss this
work_struct.
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Jarek Poplawski <jarkao2@o2.pl>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Revert: 2d771cd8

This is dangerous if enabled and a better solution to the
problem is being worked on.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SPARC64_NSEC_PER_CYC_SHIFT was set too high.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit c8fdd247.

It turns out the kernel was correct, and the gcc complaint was a gcc
bug.  The preferred stack boundary is expressed not in bytes, but in the
the log2() of the preferred boundary, so "-mpreferred-stack-boundary=2"
is in fact exactly what we want, but a gcc that is compiled for x86-64
will consider it an error (because the 64-bit calling sequence says that
the stack should be 16-byte aligned) even if we are then using "-m32" to
generate 32-bit code.
Noted-by: NMikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: Jan Hubicka <jh@suse.cz>
Acked-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.linux-nfs.org/pub/linux/nfs-2.6:
  SUNRPC: Fix sparse warnings
  NLM: Fix sparse warnings
  NFS: Fix more sparse warnings
  NFS: Fix some 'sparse' warnings...
  SUNRPC: remove dead variable 'rpciod_running'
  NFS4: Fix incorrect use of sizeof() in fs/nfs/nfs4xdr.c
  NFS: use zero_user_page
  NLM: don't use CLONE_SIGHAND in nlmclnt_recovery
  NLM: Fix locking client timeouts...

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  sata_via: pcim_iomap_regions() conversion missed BAR5
  libata: remove libata.spindown_compat
  sata_nv: fix fallout of devres conversion
  drivers/ata: remove the wildcard from sata_nv driver

pcim_iomap_regions() conversion missed BAR5.  Fix it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

With STANDBYDOWN tracking added, libata.spindown_compat isn't
necessary anymore.  If userspace shutdown(8) issues STANDBYNOW, libata
warns.  If userspace shutdown(8) doesn't issue STANDBYNOW, libata does
the right thing.  Userspace can tell whether kernel supports spindown
by testing whether sysfs node manage_start_stop exists as before.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

As with all other drivers, sata_nv's hpriv is allocated with
devm_kzalloc() and there's no need to free it explicitly.  Kill
nv_remove_one() which incorrectly used kfree() instead of devm_kfree()
and use ata_pci_remove_one() directly.

Original fix is from Peer Chen.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Because nvidia SATA controllers onward base on AHCI, so wildcard in sata_nv
driver is unnecessary.  Also the wildcard sometimes cause sata_nv driver to
be loaded for AHCI controllers,which is not as expected.
Signed-off-by: NPeer Chen <pchen@nvidia.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

pci_enable_msi failure is a normal event so we should not print any error.
Going over the code I spotted a missing pci_disable_msi() leak when irq
allocation fails. The whole code also needed a cleanup, so I combined the
two different calls to pci_request_irq into a single call making this
look a lot better. All #ifdef CONFIG_PCI_MSI's have been removed.

Compile tested with both CONFIG_PCI_MSI enabled and disabled.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

pci_enable_msi calls can fail for normal operational reasons. Driver
should not print an error message in that case. Fix a leak that leaves
msi enabled if pci_request_irq fails. We can remove CONFIG_PCI_MSI
ifdefs alltogether
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

NetXen: Fix for driver on System-p
This patch will fix a ping issue on system-p

Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off by: Adhiraj Joshi <adhiraj@netxen.com>
Signed-by: NMithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Spidernet was the driver I original did all the node-aware netdevice
allocation for, but after a year it still hasn't hit mainline.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The hardware must not see that is given ownership of a buffer until it is
completely written, and when the driver receives ownership of a buffer,
it must ensure that any other reads to the buffer reflect its final
state.  Thus, I/O barriers are added where required.

Without this patch, I have observed GCC reordering the setting of
bdp->length and bdp->status in gfar_new_skb.  Hardware reordering
was also theoretically possible.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix link speed detection change.
Thanks to Stefan Roese <sr@denx.de> for finding this bug.

CC: Stefan Roese <sr@denx.de>
Signed-off-by: NEugene Surovegin <ebs@ebshome.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Original patch is from Jeff Haran  <jharan@brocade.com> with my minor style
fixes. His comments follow:

The first problem was in the function that configures the PHY for
autonegotiation, genmii_setup_aneg(). The original code does a
read/modify/write of the autonegotiation advertizement register (reg 4),
followed by a read/modify/write of the control register (reg 0). While
the original code follows the proper procedure as per reading the IEEE
specs, what I found is that on at least one PHY model (National DP83843)
the read of the control register comes back with the soft reset bit set
(bit 15). Because of the read/modify/write operation, this causes the
write to write a 1 back to the reset bit, which initiates a software
reset of the PHY. This software reset causes the PHY to return to its
power up state which advertizes all modes of operation, thus negating
the write to the autoneg advertizement register. The modification is to
spin reading the control register until the soft reset bit is clear
before doing the modify/write.
The second problem was in the function that configures the PHY for
forced operation, genmii_setup_forced(). The original code initiates a
software reset operation via a write of a 1 to bit 15 of the control
register (reg 0), but then proceeds to do a second write to that same
register without waiting until that reset bit is cleared by the PHY
itself (which according to the IEEE specs indicates that the PHY reset
is complete). This is a violation of how one is supposed to use this
software reset feature of these PHYs and I believe was the cause of
mysterious, difficult to reproduce link failures that we've observed on
some of our systems that use this driver. The fix is to modify the
function so that it spins waiting for the reset bit to clear after doing
the soft reset and before doing the subsequent write.
Signed-off-by: NJeff Haran <jharan@brocade.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NEugene Surovegin <ebs@ebshome.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix "Section mismatch" warnings
Signed-off-by: NEugene Surovegin <ebs@ebshome.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Do some memory barrier changes for safety/perfomance:
Don't need read after update to index, mmiowb() followed by read at end
of irq is sufficient.
Signed-off-by: NStephn Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This workaround was added to deal with NAPI core and how
it affected dual port shared polling. It turned out not to
be necessary. Stopping device 0 only doesn't stop NAPI from
working completely after that.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make sure that if we ever get a MIB counter overflow interrupt (normally
masked off), that the IRQ is cleared.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When driver can't allocate receive buffer it drops incoming
packet. Keep a counter.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Align the PHY setup of the sky2 driver with the vendor sk98lin (10.0.4.3)
driver. The PHY register settings are mostly black magic, even with access
to the documentation it isn't clear what the right values are. The changes
are mostly comments, the code change only affects the Yukon FE (100 mbit only)
version.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The problems with Gigabyte motherboards are system configuration dependent.
Since it works fine for some users, it doesn't make sense to deprive
them.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

As mentioned in http://bugzilla.kernel.org/show_bug.cgi?id=5015
The helptext implies that this is on by default.
This may be true on some distros (Fedora/RHEL have it enabled
in /etc/sysctl.conf), but the kernel defaults to it off.
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These two congestion control modules share code.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add more comments to describe our version of tcp_slow_start().
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We presently use lock_sock() to acquire a lock on a socket in
hci_sock_dev_event(), but this goes BUG because lock_sock()
can sleep and we're already holding a read-write spinlock at
that point. So, we must use the non-sleeping BH version,
bh_lock_sock().

However, hci_sock_dev_event() is called from user context and
hence using simply bh_lock_sock() will deadlock against a
concurrent softirq that tries to acquire a lock on the same
socket. Hence, disabling BH's before acquiring the socket lock
and enable them afterwards, is the proper solution to fix
socket locking in hci_sock_dev_event().
Signed-off-by: NSatyam Sharma <ssatyam@cse.iitk.ac.in>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Noticed by Matvejchikov Ilya.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After initializing dev->_xmit_lock register_netdevice()
sets lockdep class according to dev->type.

Idea of this patch - by David Miller.

Reported & tested by: "Yuriy N. Shkandybin" <jura@netams.com>
Signed-off-by: NJarek Poplawski <jarkao2@o2.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function ipxrtr_route_packet() takes a 'len' argument of type
size_t. However, its prototype in af_ipx.c incorrectly suggests that the
corresponding argument is of type 'int' instead.

Discovered by building with --combine and letting the compiler see it
all at once.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After a suspend/resume cycle, the UART may have been reset into
low-speed mode -- either because it's actually been reset, or because
the firmware pokes at the old-style divisor registers. If we detected it
as a NS16550A SuperIO chip in the first place and set baud_base to
921600, then we should do so again in the resume path.

This patch adds that code to serial8250_resume_port(), and also makes
serial8250_resume() actually call serial8250_resume_port() for each port
instead of just calling uart_resume_port() directly. And thus fixes
serial port operation after suspend/resume.

It also fixes a bogus comment where we write the EXCR2 register with a
comment saying /* EXCR1 */
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>