Some nvram related cleanup:

1. Add a tg3_nvram_read_swab() since swabing the data is frequently
done.

2. Add a function to convert nvram address to physical address
instead of doing it in 2 separate places.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethtool memory test on 5787 requires a new memory table.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support one-shot MSI on 5787.

This one-shot MSI idea is credited to David Miller. In this mode, MSI
disables itself automatically after it is generated, saving the driver
a register access to disable it for NAPI.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support ipv6 tx csum on 5787 by setting NETIF_F_HW_CSUM.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support 5787 hardware TSO using a new flag TG3_FLG2_HW_TSO_2.

Since the TSO interface is slightly different and these chips have
finally fixed the 4GB DMA problem and do not have the 40-bit DMA
problem, a new hard_start_xmit is used for these chips. All previous
chips will use the old hard_start_xmit that is now renamed
tg3_start_xmit_dma_bug().
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support additional nvrams and new nvram format for 5787 and 5754.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add basic support for 2 new chips 5787 and 5754.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch turns the RTNL from a semaphore to a new 2.6.16 mutex and
gets rid of some of the leftover legacy.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Here goes a patch for supporting TOIM3232 based serial IrDA dongles.
The code is based on the tekram dongle code.

It's been tested with a TOIM3232 based IRWave 320S dongle. It may work
for TOIM4232 dongles, although it's not been tested.
Signed-off-by: NDavid Basden <davidb-irda@rcpt.to>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix-up tg3_get_ringparam() to return the correct parameters.

Set the jumbo rx ring parameter only if it is supported by the chip
and currently in use.

Add missing value for tx_max_pending, noticed by Rick Jones.

Update version to 3.51.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing netif_running() checks in tg3's dev->set_multicast_list()
and dev->set_mac_address(). If not netif_running(), these 2 calls can
simply return 0 after storing the new settings if required.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts 2 IrDA drivers pci_module_init() calls to
pci_register_driver().
Signed-off-by: NChristophe Lucas <clucas@ifrance.com>
Signed-off-by: NDomen Puncer <domen@coderock.org>
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces the deprecated sti/cli routines with the corresponding
spin_lock ones.
Signed-off-by: NDavid chosrova <david.chosrova@libertysurf.fr>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch simply adds support for a variation of the nsc-ircc PC8739x
chipset, found in some IBM Thinkpad laptops.
Signed-off-by: NJean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch brings the nsc-ircc code to a more up to date power
management scheme, following the current device model.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NRudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This enables PnP support for the nsc-ircc chipset.
Since we can't fetch the chipset cfg_base from the PnP layer, we just use
the PnP information as one more hint when probing the chip.
Signed-off-by: NJean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: NSamuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Include <linux/vmalloc.h> so that it compiles properly on all archs.

Update version to 1.4.38.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update version to 1.4.37.

Add missing flush_scheduled_work() in bnx2_suspend as noted by Jeff
Garzik.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support bigger rx ring sizes (up to 1020) in the rx fast path.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Increase maximum receive ring size from 255 to 1020 by supporting
up to 4 linked pages of receive descriptors. To accomodate the
higher memory usage, each physical descriptor page is allocated
separately and the software ring that keeps track of the SKBs and the
DMA addresses is allocated using vmalloc.

Some of the receive-related fields in the bp structure are re-
organized a bit for better locality of reference.

The max. was reduced to 1020 from 4080 after discussion with David
Miller.

This patch contains ring init code changes only. This next patch
contains rx data path code changes.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the rx code path that does not handle the full rx ring correctly.

When the rx ring is set to the max. size (i.e. 255), the consumer and
producer indices will be the same when completing an rx packet. Fix
the rx code to handle this condition properly.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ETHTOOL_GREGS support.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eliminate some of the registers in ethtool register test to reduce
driver size.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update version to 3.50.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support WoL during shutdown by calling
tg3_set_power_state(tp, PCI_D3hot) during tg3_close().

Change the power state parameter to pci_power_t type and use
constants defined in pci.h.

Certain ethtool operations cannot be performed after tg3_close()
because the device will go to low power state. Add return -EAGAIN
in such cases where appropriate.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable TSO by default on newer chips that support TSO in hardware.
Leave TSO off by default on older chips that do firmware TSO because
performance is slightly lower.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for 5714S and 5715S.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sun does't put an SEEPROM behind the tigon3 chip, among other things,
so accesses to these areas just give bus timeouts.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 40-bit DMA workaround recently implemented for 5714, 5715, and
5780 needs to be expanded because there may be other tg3 devices
behind the EPB Express to PCIX bridge in the 5780 class device.

For example, some 4-port card or mother board designs have 5704 behind
the 5714.

All devices behind the EPB require the 40-bit DMA workaround.

Thanks to Chris Elmquist again for reporting the problem and testing
the patch.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

semaphore to mutexes conversion.

the conversion was generated via scripts, and the result was validated
automatically via a script as well.

build-tested.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix gcc warning: ipw2100.c:2460: ISO C90 forbids mixed declarations and code
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStefan Rompf <stefan@loplof.de>
Signed-off-by: Andrea Merello <andreamrl at tiscali it>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a big array overun found by the Coverity checker.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch modifies the driver to support the ipw2200-fw-3.0 image format.

The 3.0 fw image does not add any new capabilities, but as a result of
image format changes, it should fix two problems experienced by users:

1) Race conditions with the request_firmware interface and udev/hotplug
are improved as only a single request_firmware call is now required to
load the firmware and microcode (vs. 3 separate calls previously)

2) The monitor mode firmware (sniffer) is now packaged with the correct
boot image so it can now function without frequent restarts.

Note: Once you apply this patch, you will also need to upgrade your
firmware image to the 3.0 version available from:

        http://ipw2200.sf.net/firmware.phpSigned-off-by: NJames Ketrenos <jketreno@linux.intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch allows the user to set the handover threshold, i.e. the number
of consecutively missed beacons that will trigger a roaming attempt. The
disassociation threshold is set to 3 times the handover threshold.
Signed-off-by: NOlivier Hochreutiner <olivier.hochreutiner@epfl.ch>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This forces one antenna or the other, if the background noise is
significantly quieter in one than the other. It favors the quieter
antenna, and won't kick in unless the difference is significant.
Signed-off-by: NCahill, Ben M <ben.m.cahill@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>