precise_ptr option causes dysfunction with hdsp driver.
Turn it off as default.
Signed-off-by: NRemy Bruno <remy.bruno@trinnov.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Some modem codec seem to fail in the initialization, and this
stopped loading of the whole module although the audio is OK.
Since it's usually a non-fatal issue, the driver tries to proceed
to initialize now.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Fix wrong error checks of *_ch_mode_put() in patch_realtek.c and
patch_analog.c.  snd_hda_ch_mode_put() could return a positive
value for success, too.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

This patch fixes incorrect assignment of swap_rear,
which was broken since patch 'ymfpci - make rear channel swap optional'
It removes module_param rear_swap.
Signed-off-by: NGlen Masgai <mimosius@gmx.de>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Use the roundup macro instead of manual calculations.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Use the ALIGN macro instead of manual calculations.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

New PCI ID described and tested Spectr <spectr@gmail.com> .
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Don't include <linux/i2c-dev.h> as it's not needed.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Handle the return value of usb_register() in the module_init function.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

add __devinitdata to struct whitelist, since it's used within
a __devinit function.
Add const attribute to iterator variable, too.
Compile-tested (no section warnings etc.) and run-tested
on vt8233, 2.6.18-mm3 (hopefully applies well to current ALSA).
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  [PATCH] Generic HID layer - update MAINTAINERS
  input/hid: Supporting more keys from the HUT Consumer Page
  [PATCH] Generic HID layer - build: USB_HID should select HID

Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the redirect packet of the router if the jiffies wraparound.
Signed-off-by: NLi Yewang <lyw@nanjing-fnst.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The message logged in tcp_v4_inbound_md5_hash when the hash was expected
but not found was reversed.
Signed-off-by: NLeigh Brown <leigh@solinno.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

md5sig_info.alloced4 must be set to zero when freeing keys4, otherwise
it will not be alloc'd again when another key is added to the same
socket by tcp_v4_md5_do_add.
Signed-off-by: NLeigh Brown <leigh@solinno.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Linus has changed work queue structure and has not tested it with
connector compiled in, his changes break the build.

Attached patch fixes compilation error.

Patch is against commit 99f5e971.

Thanks to Toralf Förster for pointing this out.
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update version to 3.71.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5906 PHY requires a special register bit to power down and up the
PHY.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hot-plug scripts can call tg3_open() as soon as register_netdev() is
called in tg3_init_one().  We need to call pci_set_drvdata() before
register_netdev(), and netif_carrier_off() needs to be moved to
tg3_open() to avoid race conditions.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tp->link_config.orig_* values must be assigned during
tg3_set_settings() because these values will be used to setup the
link speed during tg3_open().  Without these assignments, the link
speed settings will be all messed by if tg3_set_settings() is called
when the device is down.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Although the menu dependencies in net/ipv6/netfilter/Kconfig
guard the entries in that file from the Kconfig GUI, this does
not prevent them from being selected still via "make oldconfig"
when IPV6 etc. is disabled.

So add explicit dependencies.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the configured MAC address instead of the permanent MAC address
for loopback frames.

Update version to 1.5.2.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Length was not calculated correctly if the NVRAM offset is on a non-
aligned offset.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was an off-by-one bug in bnx2_tx_avail().  If the tx ring is
completely full, the producer and consumer indices may be apart by
256 even though the ring size is only 255.  One entry in the ring is
unused and must be properly accounted for when calculating the number
of available entries.  The bug caused the tx ring entries to be
reused by mistake, overwriting active entries, and ultimately causing
it to crash.

This bug rarely occurs because the tx ring is rarely completely full.
We always stop when there is less than MAX_SKB_FRAGS entries available
in the ring.

Thanks to Corey Kovacs <cjk@techma.com> and Andy Gospodarek
<agospoda@redhat.com> for reporting the problem and helping to collect
debug information.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rose_add_loopback_neigh uses kmalloc and the callers were ignoring the
error value.  Rewrite to let the caller deal with the allocation.  This
allows the use of static allocation of kmalloc use entirely.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ax25_linkfail_register uses kmalloc and the callers were ignoring the
error value.  Rewrite to let the caller deal with the allocation.  This
allows the use of static allocation of kmalloc use entirely.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix ax25_listen_register to return something that's a sane error code,
then all callers to use it.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace ax25_protocol_register by ax25_register_pid which assumes the
caller has done the memory allocation.  This allows replacing the
kmalloc allocations entirely by static allocations.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent fix 0506d406 made obvious that
error values were not being propagated through the AX.25 stack.  To help
with that this patch marks all kmalloc users in the AX.25, NETROM and
ROSE stacks as __must_check.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace kmalloc+memset with kzalloc
Signed-off-by: NYan Burman <burman.yan@gmail.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] longhaul compile fix.
  [CPUFREQ] Advise not to use longhaul on VIA C7.
  [CPUFREQ] set policy->curfreq on initialization
  [CPUFREQ] Trivial cleanup for acpi read/write port in acpi-cpufreq.c
  [CPUFREQ] fixes typo in cpufreq.c

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Recent workqueue changes basically make this a formal requirement.

Also, move atomic32.o from lib-y to obj-y since it exports symbols
to modules.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some gcc's are more anal than others about empty switch labels.
error: label at end of compound statement
Signed-off-by: NDave Jones <davej@redhat.com>

C7's are centrino speedstep-alike.
Signed-off-by: NDave Jones <davej@redhat.com>

Check the correct variable and set policy->cur upon acpi-cpufreq
initialization to allow the userspace governor to be used as default.
Signed-off-by: NMattia Dongili <malattia@linux.it>
Acked-by: N"Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDave Jones <davej@redhat.com>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>