This means passing in a suitable destination address.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the support for the Energy-Efficient Ethernet (EEE)
to the Physical Abstraction Layer.
To support the EEE we have to access to the MMD registers 3.20 and
7.60/61. So two new functions have been added to read/write the MMD
registers (clause 45).

An Ethernet driver (I tested the stmmac) can invoke the phy_init_eee to properly
check if the EEE is supported by the PHYs and it can also set the clock
stop enable bit in the 3.0 register.
The phy_get_eee_err can be used for reporting the number of time where
the PHY failed to complete its normal wake sequence.

In the end, this patch also adds the EEE ethtool support implementing:
 o phy_ethtool_set_eee
 o phy_ethtool_get_eee

v1: initial patch
v2: fixed some errors especially on naming convention
v3: renamed again the mmd read/write functions thank to Ben's feedback
v4: moved file to phy.c and added the ethtool support.
v5: fixed phy_adv_to_eee, phy_eee_to_supported, phy_eee_to_adv return
    values according to ethtool API (thanks to Ben's feedback).
    Renamed some macros to avoid too long names.
v6: fixed kernel-doc comments to be properly parsed.
    Fixed the phy_init_eee function: we need to check which link mode
    was autonegotiated and then the corresponding bits in 7.60 and 7.61
    registers.
v7: reviewed the way to get the negotiated settings.
v8: fixed a problem in the phy_init_eee return value erroneously added
    when included the phy_read_status call.
v9: do not remove the MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T
    and fixed the eee_{cap,lp,adv} declaration as "int" instead of u16.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the Energy Efficient Ethernet support to the stmmac.

Please see the driver's documentation for further details about this support
in the driver.

Thanks also goes to Rayagond Kokatanur for his first implementation.

Note:
 to clearly manage and expose the lpi interrupt status and eee ethtool
 stats I've had to do some modifications to the driver's design and I
 found really useful to move other parts of the code (e.g. mmc irq stat)
 in the main directly. So this means that some core has been reworked
 to introduce the EEE.

v1: initial patch
v2: fixed some sparse issues (typos)
v3: erroneously sent the v2 renamed as v3
v4:
	o Fixed the return value of the stmmac_eee_init as suggested by D.Miller
	o Totally reviewed the ethtool support for EEE
	o Added a new internal parameter to tune the SW timer for TX LPI.
v5: do not change any eee setting in case of the stmmac_ethtool_op_set_eee fails
    (it has to return -EOPNOTSUPP in that case).
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces the obsolete strict_strtoul with kstrtoint.

v2: also removed casting on kstrtoul.
v3: use kstrtoint instead of kstrtoul due to all vars are integer.
    thanks to E. Dumazet.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 1f85d58c
    cnic: Remove uio mem[0].

introduced a regression as older versions of userspace app still rely
on this mmap.  Restore the mmap functionality and get the base address
from pci_resource_start() as the nedev->base_addr has been deprecated for
PCI devices.

Update version to 2.5.12.
Signed-off-by: NMichael Chan <mchan@broadocm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Set the ethtool_dump flag (=ETH_FW_DUMP_DISABLE) when dump is disabled.
o update driver version to 4.0.80
Signed-off-by: NManish chopra <manish.chopra@qlogic.com>
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After SKB is queued into tx_queue, it will be freed if request_gop is NULL.
However, no dequeue action is called in this situation, it is likely that
tx_queue constains freed SKB. This patch should fix this issue, and it is
based on 3.5.0-rc4+.

This issue is found through code inspection, no bug is seen with it currently.
I run netperf test for several hours, and no network regression was found.
Signed-off-by: NAnnie Li <annie.li@oracle.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the failing merge in net-next by reverting the last
net-next merge for caif_hsi.c and then merge in the commit:
"caif-hsi: Bugfix - Piggyback'ed embedded CAIF frame lost"
from the net repository.

The commit:"caif-hsi: Add missing return in error path" from
net repository was dropped, as it changed code previously removed in the
net-next repository.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using NLMSG_GOODSIZE results in multiple pages being used as
nlmsg_new() will automatically add the size of the netlink
header to the payload thus exceeding the page limit.

NLMSG_DEFAULT_SIZE takes this into account.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a number of warnings such as:

  CC      drivers/net/ethernet/ti/davinci_cpdma.o
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: data definition
has no type or storage class
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: type defaults to
‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: parameter names
(without types) in function declaration
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The correct behavior is to program the interrupt coalescing regs
(RXICr/TXICr) in accordance with the Rx/Tx Q's "rx/txcoalescing"
flag. That is, if the coalescing flag is 0 for a given Rx/Tx queue
then the corresponding coalescing register should be cleared.
This behavior is correctly implemented for the single-queue mode
(SQ_SG_MODE), but not for the multi-queue mode (MQ_MG_MODE).
This fixes the later case.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

usbnet_disconnect() will set intfdata to NULL before calling
the minidriver unbind function.  The cdc_wdm subdriver cannot
know that it is disconnecting until the qmi_wwan unbind
function has called its disconnect function.  This means that
we must be able to support the cdc_wdm subdriver operating
normally while usbnet_disconnect() is running, and in
particular that intfdata may be NULL.

The only place this matters is in qmi_wwan_cdc_wdm_manage_power
which is called from cdc_wdm.  Simply testing for NULL
intfdata there is sufficient to allow it to continue working
at all times.

Fixes this Oops where a cdc-wdm device was closed while the
USB device was disconnecting, causing wdm_release to call
qmi_wwan_cdc_wdm_manage_power after intfdata was set to
NULL by usbnet_disconnect:

[41819.087460] BUG: unable to handle kernel NULL pointer dereference at 00000080
[41819.087815] IP: [<f8640458>] qmi_wwan_manage_power+0x68/0x90 [qmi_wwan]
[41819.088028] *pdpt = 000000000314f001 *pde = 0000000000000000
[41819.088028] Oops: 0002 [#1] SMP
[41819.088028] Modules linked in: qmi_wwan option usb_wwan usbserial usbnet
cdc_wdm nls_iso8859_1 nls_cp437 vfat fat usb_storage bnep rfcomm bluetooth
parport_pc ppdev binfmt_misc iptable_nat nf_nat nf_conntrack_ipv4
nf_conntrack nf_defrag_ipv4 iptable_mangle iptable_filter ip_tables
x_tables dm_crypt uvcvideo snd_hda_codec_realtek snd_hda_intel
videobuf2_core snd_hda_codec joydev videodev videobuf2_vmalloc
hid_multitouch snd_hwdep arc4 videobuf2_memops snd_pcm snd_seq_midi
snd_rawmidi snd_seq_midi_event ath9k mac80211 snd_seq ath9k_common ath9k_hw
ath snd_timer snd_seq_device sparse_keymap dm_multipath scsi_dh coretemp
mac_hid snd soundcore cfg80211 snd_page_alloc psmouse serio_raw microcode
lp parport dm_mirror dm_region_hash dm_log usbhid hid i915 drm_kms_helper
drm r8169 i2c_algo_bit wmi video [last unloaded: qmi_wwan]
[41819.088028]
[41819.088028] Pid: 23292, comm: qmicli Not tainted 3.4.0-5-generic #11-Ubuntu GIGABYTE T1005/T1005
[41819.088028] EIP: 0060:[<f8640458>] EFLAGS: 00010246 CPU: 1
[41819.088028] EIP is at qmi_wwan_manage_power+0x68/0x90 [qmi_wwan]
[41819.088028] EAX: 00000000 EBX: 00000000 ECX: 000000c3 EDX: 00000000
[41819.088028] ESI: c3b27658 EDI: 00000000 EBP: c298bea4 ESP: c298be98
[41819.088028]  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[41819.088028] CR0: 8005003b CR2: 00000080 CR3: 3605e000 CR4: 000007f0
[41819.088028] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[41819.088028] DR6: ffff0ff0 DR7: 00000400
[41819.088028] Process qmicli (pid: 23292, ti=c298a000 task=f343b280 task.ti=c298a000)
[41819.088028] Stack:
[41819.088028]  00000000 c3b27658 e2a80d00 c298beb0 f864051a c3b27600 c298bec0 f9027099
[41819.088028]  c2fd6000 00000008 c298bef0 c1147f96 00000001 00000000 00000000 f4e54790
[41819.088028]  ecf43a00 ecf43a00 c2fd6008 c2fd6000 ebbd7600 ffffffb9 c298bf08 c1144474
[41819.088028] Call Trace:
[41819.088028]  [<f864051a>] qmi_wwan_cdc_wdm_manage_power+0x1a/0x20 [qmi_wwan]
[41819.088028]  [<f9027099>] wdm_release+0x69/0x70 [cdc_wdm]
[41819.088028]  [<c1147f96>] fput+0xe6/0x210
[41819.088028]  [<c1144474>] filp_close+0x54/0x80
[41819.088028]  [<c1046a65>] put_files_struct+0x75/0xc0
[41819.088028]  [<c1046b56>] exit_files+0x46/0x60
[41819.088028]  [<c1046f81>] do_exit+0x141/0x780
[41819.088028]  [<c107248f>] ? wake_up_state+0xf/0x20
[41819.088028]  [<c1053f48>] ? signal_wake_up+0x28/0x40
[41819.088028]  [<c1054f3b>] ? zap_other_threads+0x6b/0x80
[41819.088028]  [<c1047864>] do_group_exit+0x34/0xa0
[41819.088028]  [<c10478e8>] sys_exit_group+0x18/0x20
[41819.088028]  [<c15bb7df>] sysenter_do_call+0x12/0x28
[41819.088028] Code: 04 83 e7 01 c1 e7 03 0f b6 42 18 83 e0 f7 09 f8 88 42
18 8b 43 04 e8 48 9a dd c8 89 f0 8b 5d f4 8b 75 f8 8b 7d fc 89 ec 5d c3 90
<f0> ff 88 80 00 00 00 0f 94 c0 84 c0 75 b7 31 f6 8b 5d f4 89 f0
[41819.088028] EIP: [<f8640458>] qmi_wwan_manage_power+0x68/0x90 [qmi_wwan] SS:ESP 0068:c298be98
[41819.088028] CR2: 0000000000000080
[41819.149492] ---[ end trace 0944479ff8257f55 ]---
Reported-by: NMarius Bjørnstad Kotsbak <marius.kotsbak@gmail.com>
Cc: <stable@vger.kernel.org> # v3.4
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As we don't provide custom regulatory rules to cfg80211,
"chan->max_power" remains uninitialized (0dbm) and
"chan->max_reg_power" will contain maximum power for a channel
extracted from regulatory rules provided by CRDA; hence use
"chan->max_reg_power" in reg_notifier handler instead of
"chan->max_power" to set max_power in firmware.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since we don't support custom regulatory domains,
WIPHY_FLAG_CUSTOM_REGULATORY should not be enabled during wiphy
registration.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"priv->max_tx_power_level" and "priv->min_tx_power_level" variables
are initialized to maximum and minimum power levels supported by
hardware by sending correct firmware command.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We miss to wakeup main thread after adding command to cmd pending
queue at follwing places. These commands are handled later when
main thread is woken up for handling an interrupt for sleep event
from firmware. This adds worst case delay of 50msec.

1) We don't wakeup main thread when asynchronous command is added
to cmd pending queue. Move queue_work() call from
mwifiex_wait_queue_complete() to mwifiex_send_cmd_async() to wakeup
main thread for sync as well as async commands.

2) Scan operation is triggered due to following reasons
   a) request from user (ex. "iw scan" command)
   b) Scan performed by driver internally.
   In first case main thread is woken up when first scan command is
queued in cmd pending queue (we don't need to wakeup main thread for
subsequent scan commands, because they are queued in scan command
response handler), but it is not done for second case. queue_work()
is moved inside mwifiex_scan_networks() to handle both the cases.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The initvals tool from https://github.com/mcgrof/qca-swiss-army-knife has
been modified to detect identical initval tables and replace them with
macros. This patch contains the generated changes.

On MIPS this reduces the binary size by 24 KB with no runtime changes.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Generated using the initvals tool from the qca-swiss-army-knife repository
from https://github.com/mcgrof/qca-swiss-army-knifeSigned-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

seems i got a message like this
ath: phy0: BT_Status_Update: is_link=0, linkId=2,
state=1, SEQ=-2085766476 initially.
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k_hw_mci_is_enabled wrapper also takes care of
ATH9K_HW_CAP_MCI being set for the AR9462 under test.
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k_ani_reset (which is called at reset time) uses a state variable
ani->update_ani to prevent the ANI noise immunity state on the operating
channel from being overwritten by background scans. Unfortunately this
is also being set for AP mode, since it's mixed with code that is only
supposed to change the default settings after a reset.

In AP mode this has the side effect of having ANI run, but being unable to
change its runtime noise immunity level, making it effectively useless.

Fix this by getting rid of ani->update_ani and passing a parameter to
ath9k_hw_set_ofdm_nil and ath9k_hw_set_cck_nil instead.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Every now and then, after resuming from suspend, the iwlegacy driver
prints
    iwl4965 0000:03:00.0: Queue 2 stuck for 2000 ms.
    iwl4965 0000:03:00.0: On demand firmware reload

I have no idea what causes these errors. But the code currently uses
wd_timeout in the first error. wd_timeout will generally be set at
IL_DEF_WD_TIMEOUT (ie, 2000). Perhaps printing for how long the queue
was actually stuck can clarify the cause of these errors.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/phy/phy_device.c: In function ‘get_phy_device’:
drivers/net/phy/phy_device.c:340:14: warning: ‘phy_id’ may be used uninitialized in this function [-Wmaybe-uninitialized]

GCC can't see that when we return zero we always initialize
phy_id and that's the only path where we use it.

Initialize phy_id to zero to shut it up.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a driver for BCM8706 and BCM8727 devices.  These are a 10Gig PHYs
which use MII_ADDR_C45 addressing.  They are always 10G full duplex, so
there is no autonegotiation.  All we do is report link state and send
interrupts when it changes.

If the PHY has a device tree of_node associated with it, the
"broadcom,c45-reg-init" property is used to supply register
initialization values when config_init() is called.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow PHY drivers to supply their own device matching function
(match_phy_device()), or to be matched OF compatible properties.

PHYs following IEEE802.3 clause 45 have more than one device
identifier constants, which breaks the default device matching code.
Other 10G PHYs don't follow the standard manufacturer/device
identifier register layout standards, but they do use the standard
MDIO bus protocols for register access.  Both of these require
adjustments to the PHY driver to device matching code.

If the there is an of_node associated with such a PHY, we can match it
to its driver using the "compatible" properties, just as we do with
certain platform devices.  If the "compatible" property match fails,
first check if there is a driver supplied matching function, and if
not fall back to the existing identifier matching rules.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IEEE802.3 clause 45 MDIO bus protocol allows for directly
addressing PHY registers using a 21 bit address, and is used by many
10G Ethernet PHYS.  Already existing is the ability of MDIO bus
drivers to use clause 45, with the MII_ADDR_C45 flag.  Here we add
struct phy_c45_device_ids to hold the device identifier registers
present in clause 45. struct phy_device gets a couple of new fields:
c45_ids to hold the identifiers and is_c45 to signal that it is clause
45.

get_phy_device() gets a new parameter is_c45 to indicate that the PHY
device should use the clause 45 protocol, and its callers are adjusted
to pass false.  The follow-on patch to of_mdio.c will pass true where
appropriate.

EXPORT phy_device_create() so that the follow-on patch to of_mdio.c
can use it to create phy devices for PHYs, that have non-standard
device identifier registers, based on the device tree bindings.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Different boards may require different phy reset duration.  Add property
phy-reset-duration for device tree probe, so that the boards that need
a longer reset duration can specify it in their device tree.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using gpio_request_one will require the probe fail-out call gpio_free,
which is missing currently.  Change to use devm_gpio_request_one to
fix the problem.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If bootloader or platform initialization code does not enable the
power supply to fec phy, we need to do it in fec driver before calling
fec_reset_phy to have the phy powered on.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case that bootloader or platform initialization does not set up
fec pins, the fec_reset_phy will not be able to succeed, because
fec_reset_phy is currently called before devm_pinctrl_get_select_default.
Move fec_reset_phy call to the place between devm_pinctrl_get_select_default
and fec_enet_init to have above case be taken care.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

to stop all tx queues.  Update version to 2.2.3.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

to indicate that the mising break statements are intended.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If firmware returns error status, proceed to close the iSCSI connection.
Update version to 2.5.11.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This memory region is no longer used.  Userspace gets the BAR address
directly from sysfs.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

so that it will work on any hypervisor.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>