Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 08 8月, 2007 11 次提交
  3. 07 8月, 2007 16 次提交
  5. 06 8月, 2007 3 次提交
  7. 05 8月, 2007 5 次提交
  9. 04 8月, 2007 5 次提交
    • S
      [SCSI] aacraid: prevent panic on adapter resource failure · 2b053729
      由 Salyzyn, Mark 提交于 
      If the driver fails to allocate the contiguous (DMAable) memory for
system reasons, we fail to load the instance, but then we try to free
the <nul> allocation in the cleanup code and we get a panic in
pci_free_consistent(). This is reported against an older kernel, hope
this is relevant for latest/greatest.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      2b053729
    • B
      [SCSI] aha152x: use data accessors and !use_sg cleanup · 2338545a
      由 Boaz Harrosh 提交于 
      And finally this is the regular !use_sg cleanup
and use of data accessors.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      2338545a
    • B
      [SCSI] aha152x: Fix check_condition code-path · 45333ffa
      由 Boaz Harrosh 提交于 
      check_condition code-path was similar but more
complicated to Reset. It went like this:

  1. extra space was allocated at aha152x_scdata for mirroring
    scsi_cmnd members.
  2. At aha152x_internal_queue() every not check_condition
    (REQUEST_SENSE) command was copied to above members in
    case of error.
  3. At busfree_run() in the DONE_CS phase if a Status of
    SAM_STAT_CHECK_CONDITION was detected. The command was
    re-queued Internally using aha152x_internal_queue(,,check_condition,)
    The old command members are over written with the
    REQUEST_SENSE info.
  4. At busfree_run() in the DONE_CS phase again. If it is a
    check_condition command, info was restored from mirror
    made at first call to aha152x_internal_queue() (see 2)
    and the command is completed.

What I did is:

  1. Allocate less space in aha152x_scdata only for the 16-byte
    original command. (which is actually not needed by scsi-ml
    anymore at this stage. But this is to much knowledge of scsi-ml)
  2. If Status == SAM_STAT_CHECK_CONDITION, then like before
     re-queue a REQUEST_SENSE command. But only now save original
     command members. (Less of them)
  3. In aha152x_internal_queue(), just like for Reset, use the
    check_condition hint to set differently the working members.
    execute the command.
  4. At busfree_run() in the DONE_CS phase again. restore needed
     members.

While at it. This patch fixes a BUG. Old code when sending
a REQUEST_SENSE for a failed command. Would than return with
cmd->resid == 0 which was the status of the REQUEST_SENSE.
The failing command resid was lost. And when would resid
be interesting if not on a failing command?
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      45333ffa
    • B
      [SCSI] aha152x: Clean Reset path · 66acdb03
      由 Boaz Harrosh 提交于 
      What Reset code was doing:  Save command's important/dangerous
Info on stack. NULL those members from scsi_cmnd.
Issue a Reset. wait for it to finish than restore members
and return.

What I do is save or NULL nothing. But use the "resetting"
hint in aha152x_internal_queue() to NULL out working members
and leave struct scsi_cmnd alone.

The indent here looks funny but it will change/drop in last
patch and it is clear this way what changed.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      66acdb03
    • B
      [SCSI] aha152x: preliminary fixes and some comments · 0ceb4798
      由 Boaz Harrosh 提交于 
        hunk by hunk:
  - CHECK_CONDITION is what happens to cmnd->status >> 1
    or after status_byte() macro. But here it is used
    directly on status which means 0x1 which is an undefined
    bit in the standard. And is a status that will never
    return from a target.

  - in busfree_run at the DONE_SC phase we have 3 distinct
    operation:
	1-if(DONE_SC->SCp.phase & check_condition)
          The REQUEST_SENSE command return.
          - Restore original command
	  - Than continue to operation 3.
	2-if(DONE_SC->SCp.Status==SAM_STAT_CHECK_CONDITION)
          A regular command returned with a status.
	  - Internally re-Q a REQUEST_SENSE.
	  - Do not do operation 3.
	3-
	  - Complete the command and return it to scsi-ml
     So the 0x2 in both these operations (1,2) means the scsi
     check-condition status, hence SAM_STAT_CHECK_CONDITION

  - Here the code asks about !(DONE_SC->SCp.Status & not_issued)
    but "not_issued" is an enum belonging to the "phase" member
    and not to the Status returned from target. The reason this
    works is because not_issued==1 and Also CHECK_CONDITION==1
    (remember from hunk 1). So actually the code was asking
    !(DONE_SC->SCp.Status & CHECK_CONDITION). Which means
    "Has the status been read from target yet?"
    Staus is read at status_run(). "not_issued" is
    cleared in seldo_run() which is usually earlier than
    status_run().

  So this patch does nothing as far as assembly is concerned
  but it does let the reader understand what is going on.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
      0ceb4798