There are two definitions of xpad_identify_controller(), one is used
when CONFIG_JOYSTICK_XPAD_LEDS is set, but the other one is empty
and never used, and we get a gcc warning about it:

drivers/input/joystick/xpad.c:1210:13: warning: 'xpad_identify_controller' defined but not used [-Wunused-function]

This removes the second definition.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: cae705ba ("Input: xpad - re-send LED command on present event")
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This reverts commit 27b9d5a2.

I am reverting this one, while keeping the rest of the G920 support in,
so that it immediately starts working once proper HID-mode switching
is implemented.

Quoting Dmitry Torokhov for rationale:

==
It is wrong. Aside form the fact that IMO xpad.c is the wrong place for
this code to be in, why are we waiting for the input device to be
opened by userspace before we do the switch instead of doing it
immediately?
==

Several people (Simon Wood and Michal Maly) expressed the intent to work
on proper HID switching in a short term.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Apparently the Covert Forces ID is not Covert Forces pad exclusive, but
rather denotes a new firmware version that can be found on all new
controllers and can be also updated on old hardware using Windows 10.

see: https://github.com/paroj/xpad/issues/19Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

When lighting up the segment identifying wireless controller, Instead of
sending command directly to the controller, let's do it via LED API (usinf
led_set_brightness) so that LED object state is in sync with controller
state and we'll light up the correct segment on resume as well.
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The irq_out urb is dead after suspend/ resume on my x360 wr pad. (also
reproduced by Zachary Lund [0]) Work around this by implementing
suspend, resume, and reset_resume callbacks and properly shutting down
URBs on suspend and restarting them on resume.

[0]: https://github.com/paroj/xpad/issues/6Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

There's apparently a serial number woven into both input and output
packets; neglecting to specify a valid serial number causes the controller
to ignore the rumble packets.

The scale of the rumble was also apparently halved in the packets.

The initialization packet had to be changed to allow force feedback to
work.

see https://github.com/paroj/xpad/issues/7 for details.
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Track the status of the irq_out URB to prevent submission iof new requests
while current one is active. Failure to do so results in the "URB submitted
while active" warning/stack trace.

Store pending brightness and FF effect in the driver structure and replace
it with the latest requests until the device is ready to process next
request. Alternate serving LED vs FF requests to make sure one does not
starve another. See [1] for discussion. Inspired by patch of Sarah Bessmer
[2].

[1]: http://www.spinics.net/lists/linux-input/msg40708.html
[2]: http://www.spinics.net/lists/linux-input/msg31450.htmlSigned-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Handle the "a new device is present" message properly by dynamically
creating the input device at this point in time. This means we now do not
"preallocate" all 4 devices when a single wireless base station is seen.
This requires a workqueue as we are in interrupt context when we learn
about this.

Also properly disconnect any devices that we are told are removed.
Signed-off-by: N"Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

When powering up a wireless xbox 360 controller, some wrong joystick
events are generated. It is annoying because, for example, it makes
unwanted moves in Steam big picture mode's menu.

When my controller is powering up, this packet is received by the
driver:
00000000: 00 0f 00 f0 00 cc ff cf 8b e0 86 6a 68 f0 00 20  ...........jh..
00000010: 13 e3 20 1d 30 03 40 01 50 01 ff ff              .. .0.@.P...

According to xboxdrv userspace driver source code, this packet is only
dumping a serial id and should not be interpreted as joystick events.
This issue can be easily seen with jstest:
$ jstest --event /dev/input/js0

This patch only adds a way to filter out this "serial" packet and as a
result it removes the spurous events.
Signed-off-by: NClement Calmels <clement.calmels@free.fr>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

When plugged in the Logitech G920 wheel starts with USBID 046d:c261
and behaviors as a vendor specific class. If a 'magic' byte sequence
is sent the wheel will detach and reconnect as a HID device with the
USBID 046d:c262.
Signed-off-by: NSimon Wood <simon@mungewell.org>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

walkera0701_parport_cb is a local uninitialized structure and the member
function pointers will be pointing to arbitrary locations unless they
are cleared.

Fixes: 221bcb24 ("Input: walkera0701 - use parallel port device model")
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

tgfx_parport_cb is a local uninitialized structure and the member
function pointers will be pointing to arbitrary locations unless they
are cleared.

Fixes: 4de27a63 ("Input: turbografx - use parallel port device model")
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

gc_parport_cb is a local uninitialized structure and the member
function pointers will be pointing to arbitrary locations unless they
are cleared.

Fixes: a517e87c ("Input: gamecon - use parallel port device model")
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

db9_parport_cb is a local uninitialized structure and the member
function pointers will be pointing to arbitrary locations unless they
are cleared.

Fixes: 2260c419 ("Input: db9 - use parallel port device model")
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Switch everything to the new and more capable implementation of abs().
Mainly to give the new abs() a bit of a workout.

Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Do not call xpad_identify_controller at init with wireless devices: it
conflicts with the already sent presence packet and will be called by
xpad360w_process_packet as needed anyway.
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

When we initialize the driver/device, we really don't know how many
controllers are connected.  So send a "query presence" command to the
base-station. (Command discovered by Zachary Lund)

Presence packet taken from:

https://github.com/computerquip/xpad5Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

To allow us to later create / destroy the input device from the urb
callback, we need to initialize/ deinitialize the input device from a
separate function.  So pull that logic out now to make later patches
more "obvious" as to what they do.
Signed-off-by: N"Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

as discussed here[0], x360w is the only pad that maps dpad_to_button.
This is bad for downstream developers as they have to differ between
x360 and x360w which is not intuitive.

This patch implements the suggested solution of exposing the dpad both
as axes and as buttons. This retains backward compatibility with software
already dealing with the difference while makes new software work as
expected across x360/ x360w pads.

[0] http://www.spinics.net/lists/linux-input/msg34421.htmlSigned-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Move submission logic to a single point at the end of the function.
This makes it easy to add locking/ queuing code later on.
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This code was probably wrong ever since and is redundant with
xpad_send_led_command. Both try to send a similar command to the xbox360
controller. However xpad_send_led_command correctly uses the pad_nr instead
of bInterfaceNumber to select the led and re-uses the irq_out URB instead
of creating a new one.

Note that this change only affects the two supported wireless controllers.
Tested using the xbox360 wireless controller (PC).
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The pad_nr corresponds to the lit up LED on the controller. Therefore there
should be no gaps when enumerating. Currently a LED is only re-assigned
after a controller is re-connected 4 times.

This patch uses ida to track connected pads - this way we can re-assign
freed up pad number immediately.

Consider the following case:
1. pad A is connected and gets pad_nr = 0
2. pad B is connected and gets pad_nr = 1
3. pad A is disconnected
4. pad A is connected again

using ida_simple_get() controller A now correctly gets pad_nr = 0 again.
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Rename led_no -> pad_nr: the number stored there is not the LED number - it
gets translated later on to a LED number in xpad_identify_controller;
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The "Razer Atrox Arcade Stick" features 10 buttons, and two of them (LT/RT)
don't work properly.  Change its definition in xpad_device[] (mapping
field) to fix.
Signed-off-by: NDario Scarpa <dario.scarpa@duskzone.it>
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

It is identical to the Xbox One controller but has a different product ID.
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The variable i is used to check the port to attach to and we are
supposed to save the reference of struct tgfx in the location given by
tgfx_base[i]. But after finding out the index, i is getting modified
again so we saved in a wrong index.

Fixes: 4de27a63 ("Input: turbografx - use parallel port device model")
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The variable i is used to check the port to attach to and we are
supposed to save the reference of struct gc in the location given by
gc_base[i]. But after finding out the index, i is getting modified again
so we saved in a wrong index.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Fixes: a517e87c ("Input: gamecon - use parallel port device model")
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The variable i is used to check the port to attach to and we are
supposed to save the reference of struct db9 in the location given by
db9_base[i]. But after finding out the index, i is getting modified again
so we saved in a wrong index.
While at it mark db9_base[i] as NULL after it is freed.

Fixes: 2260c419 ("Input: db9 - use parallel port device model")
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

It uses bitrev8(), so it must ensure that lib/bitrev.o gets included in
vmlinux.

Cc: Fengguang Wu <fengguang.wu@gmail.com>
Cc: yalin wang <yalin.wang2010@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Modify walkera0701 driver to use the new Parallel Port device model.
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Modify turbografx driver to use the new Parallel Port device model.
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Modify gamecon driver to use the new Parallel Port device model.
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

It uses bitrev8(), so it must ensure that lib/bitrev.o gets included in
vmlinux.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Modify db9 driver to use the new Parallel Port device model.
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Tested-By: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

abs() function can not be used with 64 bit values, so let's switch to
abs64(). From include/linux/kernel.h:

/*
 * abs() handles unsigned and signed longs, ints, shorts and chars.
 * For all input types abs() returns a signed long.
 * abs() should not be used for 64-bit types (s64, u64, long long)
 * - use abs64() for those.
 */
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of custom zhenhua_bitreverse() let's use generic bitrev8().
Signed-off-by: NYalin Wang <yalin.wang2010@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Patch 17dd3f0f: "[PATCH] drivers/input/joystick: convert to dynamic
input_dev allocation" from Sep 15, 2005, leads to the following static
checker warning:

        drivers/input/joystick/turbografx.c:235 tgfx_probe()
        error: buffer overflow 'tgfx_buttons' 5 <= 5

drivers/input/joystick/turbografx.c
   195          for (i = 0; i < n_devs; i++) {
   196                  if (n_buttons[i] < 1)
   197                          continue;
   198
   199                  if (n_buttons[i] > 6) {
                            ^^^^^^^^^^^^^^^^
Possibly off by one.  >= 6.

Let's change the upper value to ARRAY_SIZE(tgfx_buttons) to ensure we do
not reach past the end of the array.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Now that there is no paravirt TSC, the "native" is
inappropriate. The function does RDTSC, so give it the obvious
name: rdtsc().
Suggested-by: NBorislav Petkov <bp@suse.de>
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/fd43e16281991f096c1e4d21574d9e1402c62d39.1434501121.git.luto@kernel.org
[ Ported it to v4.2-rc1. ]
Signed-off-by: NIngo Molnar <mingo@kernel.org>

This timing code is hideous, and this doesn't help.  It gets rid
of one of the last users of rdtscl(), though.
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: linux-input@vger.kernel.org
Link: http://lkml.kernel.org/r/90d19b3cea0e05ca6f333d1598daa38afb993260.1434501121.git.luto@kernel.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>

The controller only receives commands when its present. So for the
correct LED to be lit the LED command has to be sent on the present
event.
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>