We need it to restore the ilk rc6 context, since the gpu wait no
requires interrupts. But in general having interrupts around should
help in code sanity, since more and more stuff is interrupt driven.

This regression has been introduced in

commit 3e960501
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Tue Nov 27 16:22:54 2012 +0000

    drm/i915: Rearrange code to only have a single method for waiting upon the ring

Like in the driver load code we need to make sure that hotplug
interrupts don't cause havoc with our modeset state, hence block them
with the existing infrastructure. Again we ignore races where we might
loose hotplug interrupts ...

Note that the driver load part of the regression has already been
fixed in

commit 52d7eced
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Sat Dec 1 21:03:22 2012 +0100

    drm/i915: reorder setup sequence to have irqs for output setup

v2: Add a note to the commit message about which patch fixed the
driver load part of the regression. Stable kernels need to backport
both patches.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=54691
Cc: stable@vger.kernel.org (for 3.8 only, plese backport
			    52d7eced first)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reported-and-Tested-by: NIlya Tumaykin <itumaykin@gmail.com>
Reviewed-by: Chris wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This increases GEN6_RC6p_THRESHOLD from 100000 to 150000. For some
reason this avoids the gen6_gt_check_fifodbg.isra warnings and
associated GPU lockups, which makes my ivy bridge machine stable.
Signed-off-by: NStéphane Marchesin <marcheu@chromium.org>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On G45 some low res modes (800x600 and 1024x768) produce a blank
screen when the display plane is enabled with with cursor plane
off.
Experiments showed that this issue occurred when the following
conditions were met:
a. a previous mode had the cursor plane enabled (Xserver).
b. this mode or the previous one was using self refresh. (Thus
   the problem was only seen with low res modes).
The screens lit up as soon as the cursor plane got enabled.
Therefore the blank screen occurred only in console mode, not
when running an Xserver.
It also seemed to be necessary to disable self refresh while briefly
enabling the cursor plane.
Signed-off-by: NEgbert Eich <eich@suse.com>
Bugzilla: https://bugs.freedesktop.org/attachment.cgi?bugid=61457Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: drop spurious whitespace change.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The second digit was off by one, which meant we accidentally treated
GT(n) as GT(n-1).  This also meant no support for GT1 at all.

Cc: stable@kernel.org
Signed-off-by: NKenneth Graunke <kenneth@whitecape.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Restore crtc->fb to the old framebuffer if queue_flip fails.

While at it, kill the pointless intel_fb temp variable.

v2: Update crtc->fb before queue_flip and restore it back
    after a failure.

Cc: stable@vger.kernel.org
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reported-and-Tested-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So use msecs_to_jiffies(10) to make the timeout the same as in the
"!has_aux_irq" case.

This patch was initially written by Daniel Vetter and posted on
pastebin a few weeks ago. I'm just bringing it to the mailing list.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Need to initialize the variable wait to false.
Signed-off-by: NSyam Sidhardhan <s.syam@samsung.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This reverts

commit 8ec22b21
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Fri May 11 18:01:34 2012 +0100

    drm/i915/hdmi: Query the live connector status bit for G4x

and

commit b0ea7d37
Author: Damien Lespiau <damien.lespiau@intel.com>
Date:   Thu Dec 13 16:09:00 2012 +0000

    drm/i915/hdmi: Read the HPD status before trying to read the EDID

They reliably cause HDMI to not be detected on some systems (like my
ivb or the bug reporters gm45). To fix up the very slow unplug issues
we might want to fire up a 2nd detect cycle a few hundred ms after
each hotplug. But for now at least make displays work again.

I somewhat suspect that this is confined to HDMI connectors, since all
the machines I have with DP+ outputs work correctly.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52361
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org.kernel.org # for 8ec22b21Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We trim the fb to fit the CRTC by computing the offset of that CRTC to
its nearest tile_row origin. This allows us to use framebuffers that are
larger than the CRTC limits without additional work.

However, we failed to compute the offset for a linear framebuffer
correctly as we treated its x-advance in whole tiles (instead of the
linear increment expected), leaving the CRTC misaligned with its
contents.

Fixes regression from commit c2c75131
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Thu Jul 5 12:17:30 2012 +0200

    drm/i915: adjust framebuffer base address on gen4+

v2: Adjust relative x-coordinate after linear alignment (vsyrjala)
v3: Repaint with pokadots (vsyrjala)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61152Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We already have the quirk entry for the mobile platform, but also
reports on some desktop versions. So be paranoid and set it
everywhere.

References: http://www.mail-archive.com/dri-devel@lists.freedesktop.org/msg33138.html
Cc: stable@vger.kernel.org
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "Sankaran, Rajesh" <rajesh.sankaran@intel.com>
Reported-and-tested-by: NMihai Moldovan <ionic@ionic.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Whilst IOMMU is enabled for the Intel GPU on Ironlake, it appears that
using WC writes to update the PTE on the GPU fails miserably. The
result looks like the majority of the writes do not land leading to
lots of screen corruption and a hard system hang.

v2: s/</<=/ to preserve the current exclusion of Sandybridge
Reported-by: NNathan Myers <ncm@cantrip.org>
Bugzilla: https://bugzilla.freedesktop.org/show_bug.cgi?id=60391Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NNathan Myers <ncm@cantrip.org>
[danvet: Remove cc: stable and add tested-by.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

HSW no longer has the PIPECONF bit for limited range RGB output.
Instead the pipe CSC unit must be used to perform that task.

The CSC pre offset are set to 0, since the incoming data is full
[0:255] range RGB, the coefficients are programmed to compress the
data into [0:219] range, and then we use either the CSC_MODE black
screen offset bit, or the CSC post offsets to shift the data to
the correct [16:235] range.

Also have to change the confiuration of all planes so that the
data is sent through the pipe CSC unit. For simplicity send the
plane data through the pipe CSC unit always, and in case full
range output is requested, the pipe CSC unit is set up with an
identity transform to pass the plane data through unchanged.

I've been told by some hardware people that the use of the pipe
CSC unit shouldn't result in any measurable increase in power
consumption numbers.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=53881
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Tested-by: NJani Monoses <jani@ubuntu.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Print out the HW context object information per ring. Even though the
existing code only utilizes the render ring, it's simple enough to
support future expansion.

I had this in a patch somewhere in a rev of the original implementation,
but I must have lost it.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
[danvet: s/context/default context/ bikeshed applied.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Yet another remnant ... this might explain why l3 remapping didn't
really work on HSW.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=57441Spotted-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The bit controlling whether PIPE_CONTROL DW/QW write targets
the global GTT or PPGTT moved moved from DW 2 bit 2 to
DW 1 bit 24 on IVB.

I verified on IVB that the fix is in fact effective. Without the fix
none of the scratch writes actually landed in the pipe control page.
With the fix the writes show up correctly.

v2: move PIPE_CONTROL_GLOBAL_GTT_IVB setup to where other flags are set
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The Intel PRM says the M1 and M2 divisors must be in the range of 10-20 and 5-9.
Since we do all calculations based on them being register values (which are
subtracted by 2) we need to specify them accordingly.
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56359
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The Intel PRM says the M1 and M2 divisors must be in the range of 10-20 and 5-9.
Since we do all calculations based on them being register values (which are
subtracted by 2) we need to specify them accordingly.
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Similarly to:

  commit 6a0d1df3d3a0d2370541164eb0595fe35dcd6de3
  Author: Damien Lespiau <damien.lespiau@intel.com>
  Date:   Tue Dec 11 15:18:28 2012 +0000

      drm/i915: Preserve the FDI line reversal override bit on CPT

DDI port support lane reversal to easy the PCB layouting work. Let's
preserve the bit configured by the BIOS (until we find how to correctly
retrieve the information from the VBT, but this does sound more fragile
then just relying on the BIOS that has, hopefully, been validated
already.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The FDI link has supported link reversal to make the PCB layout
engineer's life easier for quite a while and we have always presered
this bit as we programmed FDI_RX_CTL with a read/modify/write sequence.

We're trying to take a bit more control over what the BIOS leaves in
various register and with the introduction of DDI, started to program
FDI_RX_CTL fully.

There's a fused bit to indicate DMI link reversal and FDI defaults to
mirroring that configuration. We have a bit to override that behaviour
that we need to preserve from the BIOS.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Amending
commit 4518f611
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Wed Jan 23 16:16:35 2013 +0100

    drm/i915: dump UTS_RELEASE into the error_state

CC: stable@vger.kernel.org
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Support for real RGB332 is a rarity, most hardware only really support
C8. So use C8 instead of RGB332 when determining the format based on
depth/bpp.

This fixes 8bpp fbcon on i915, since i915 will only accept C8 and not
RGB332.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59572Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Tested-by: mlsemon35@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Set depth/bits_per_pixel to 8 for C8 format.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NDave Airlie <airlied@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As explained by Chris Wilson gem objects in stolen memory are always
coherent with the GPU so we don't need to ever flush the CPU caches for
these.

This fixes a breakage - at least with the compact sg patches applied -
during the resume/restore gtt mappings path, when we tried to clflush an
FB object in stolen memory, but since stolen objects don't have backing
pages we passed an invalid page pointer to drm_clflush_page().
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If a GPU reset occurs while a page flip has been submitted to the ring,
the flip will never complete once the ring has been reset.

The GPU reset can be detected by sampling the reset_counter before the
flip is submitted, and then while waiting for the flip, the sampled
counter is compared with the current reset_counter value.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
[danvet: Move the reset_counter assignment to an earlier place in
common code as discussed on the mailing list.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=60140Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The pending flip mask no longer set anywhere, so trying to wait for
while it's non-zero is a no-op. Remove it completely.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This has been lost in the locking rework for intel_alloc_context_page:

commit 2c34b850
Author: Ben Widawsky <ben@bwidawsk.net>
Date:   Sat Mar 19 18:14:26 2011 -0700

    drm/i915: fix ilk rc6 teardown locking

Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We already print the HWS addresses during init, so do the same for the
pipe control page. Reduces guesswork when looking at hex addresses
later.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the previous patch "drm/i915: disable shared panel fitter for
pipe" we now disable the panel fitter at the right spot in the modeset
sequence in the crtc functions on all platforms. Hence the disabling
in intel_disable_lvds is no longer required and potentially harmful
(since the plane is still enabled at this point).

Similarly on the enabling side we enable the panel fitter in the lvds
callback only once the plane is enabled. Which is too late. Hence move
this into a new intel_pre_enable_lvds callback.

Finally we can ditch lvds_encoder->pfit_dirty - this was required to
work around the crtc helper semantics, but with the new i915 modeset
infrastructure we should enable/disable the pfit only when enabling or
disabling the entire output pipeline. So separate state tracking for
the pfit is no longer required.
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
[danvet: Bikeshed the commit message a bit to stress that now we
enable/disable the pfit on i9xx platforms at the right point of time
compared to the old code.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If encoder is switched off by BIOS, but the panel fitter is left on,
we never try to turn off the panel fitter and leave it still attached
to the pipe - which can cause blurry output elsewhere.

Based on work by Chris Wilson <chris@chris-wilson.co.uk>

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58867
Cc: stable@vger.kernel.org
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Tested-by: NAndreas Sturmlechner <andreas.sturmlechner@gmail.com>
[danvet: Remove the redundant HAS_PCH_SPLIT check and add a tiny
comment.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some early bios versions seem to ship with the wrong tuning values for
the MCH, possible resulting in pipe underruns under load. Especially
on DP outputs this can lead to black screen, since DP really doesn't
like an occasional whack from an underrun.

Unfortunately the registers seem to be locked after boot, so the only
thing we can do is politely point out issues and suggest a BIOS
upgrade.

Arthur Runyan pointed us at this issue while discussion DP bugs - thus
far no confirmation from a bug report yet that it helps. But at least
some of my machines here have wrong values, so this might be useful in
understanding bug reports.

v2: After a bit more discussion with Art and Ben we've decided to only
the check the watermark values, since the OREF ones could be be a
notch more aggressive on certain machines.

Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Runyan, Arthur J <arthur.j.runyan@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's not that the assertion is incorrect, but rather that we can call
do_destroy early in loading, and we will falsely BUG().

Since contexts have been in for a while now, and in the internal APIs
are pretty stable, it should be fairly safe to remove this.

v2: Remove unused dev_priv, and dev
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The ring initialization will differ a bit in upcoming generations, and
this split will prepare the code for what's needed.

This patch also fixes a bug introduced in:
commit 99433931
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date:   Tue Jan 22 14:12:17 2013 +0200

    drm/i915: use gem_set_seqno() on hardware init

After doing the extraction, the bad error handling became obvious.  I
acknowledge that this should be two patches, but it's a pretty
small/trivial patch. If requested, I can certainly do the fix as a
distinct patch.

v2: Should be cleanup blt, not init blt on failure (Chris)

v3: Forgot to git add on v2

Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When I refactored the code initially, I forgot that gen2 uses a
different bar for the CPU mappable aperture. The agp-less code knows
nothing of generations less than 5, so we have to expand the gtt_probe
function to include the mappable base and end.

It was originally broken by me:
commit baa09f5f
Author: Ben Widawsky <ben@bwidawsk.net>
Date:   Thu Jan 24 13:49:57 2013 -0800

    drm/i915: Add probe and remove to the gtt ops
Reported-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So we can remove duplicated code. Note that this function is used not
only on IBX, but also CPT and LPT.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
[danvet: Also bikeshed s/ironlake_enable_pch_hotplug/ibx_enable_hotplug
to keep consistent with our ibx for pch naming scheme.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have more than one sprite, so a boolean simply won't cut it.
Turn sprite_scaling_enabled into a bitmask and track the state
of sprite scaler for each sprite independently.

Also don't re-enable LP watermarks until the sprite registers
have actually been written, and thus sprite scaling has really
been disabled.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

They're physically the same pins and also the same bits, duplicating
only confuses the reader. This also makes it a bit obvious that we
have quite some code duplication going on here. Squashing that is for
a larger rework in our hpd handling though.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This was a rebase error from when the patches originally landed. Since
the context size is unsigned, there is also no use in checking if it's
less than 0.

The existing code is not really wrong, but it's not simple as it should
be.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

770c1231 is the first bad commit
commit 770c1231
Author: Takashi Iwai <tiwai@suse.de>
Date:   Sat Aug 11 08:56:42 2012 +0200

    drm/i915: Fix blank panel at reopening lid

changed the register write sequence for restoring the backlight, which
helped prevent non-working backlights on some machines. Turns out that
the original sequence was the right thing to do for a different set of
machines. Worse, setting the backlight level _after_ enabling it seems
to reset it somehow. So we need to make that one conditional upon the
backlight having been reset to zero, and add the old one back.

Cargo-culting at it's best, but it seems to work.

Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47941Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>