Based on the earlier work by Tejun Heo.

There should be no functionality changes caused by this patch.

Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Based on the earlier work by Tejun Heo.

There should be no functionality changes caused by this patch.

Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Extend timeout for REQ_TYPE_ATA_{CMD,TASK} requests from WAIT_CMD (10sec)
to WAIT_WORSTCASE (30sec, already used for REQ_TYPE_ATA_TASKFILE).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Set taskfile flags for REQ_TYPE_ATA_TASKFILE requests before
  adding the request to the queue.

* Cleanup execute_drive_cmd().

* Remove unnecessary writes to HOB taskfile registers when using
  LBA48 disk for the following cases:

  - Power Management requests
    (WIN_FLUSH_CACHE[_EXT], WIN_STANDBYNOW1, WIN_IDLEIMMEDIATE commands)

  - special commands (WIN_SPECIFY, WIN_RESTORE, WIN_SETMULT)

  - Host Protected Area support (WIN_READ_NATIVE_MAX, WIN_SET_MAX)

  - /proc/ide/ SMART support (WIN_SMART with SMART_ENABLE,
    SMART_READ_VALUES and SMART_READ_THRESHOLDS subcommands)

  - write cache enabling/disabling in ide-disk
    (WIN_SETFEATURES with SETFEATURES_{EN,DIS}_WCACHE)

  - write cache flushing in ide-disk (WIN_FLUSH_CACHE[_EXT])

  - acoustic management in ide-disk
    (WIN_SETFEATURES with SETFEATURES_{EN,DIS}_AAM)

  - door (un)locking in ide-disk (WIN_DOORLOCK, WIN_DOORUNLOCK)

  - /proc/ide/hd?/identify support (WIN_IDENTIFY)

  - ACPI _GTF taskfiles
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use IDE_TFLAG_LBA48 for REQ_TYPE_ATA_TASKFILE requests in ide_end_drive_cmd()
  to decide whether we need to read HOB taskfile registers.

* Update execute_drive_cmd() accordingly.

This is a preparation for the next patch which removes unnecessary writes to
HOB taskfile registers for some ATA commands.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_TFLAG_OUT_DEVICE taskfile flag to indicate the need of writing
  the Device register and handle it in ide_tf_load().

  Update ide_tf_load() and {do_rw,flagged}_taskfile() users accordingly.

* Use struct ide_taskfile and ide_tf_load() in execute_drive_cmd().

* Make the debugging code dump all taskfile registers for both
  REQ_ATA_TYPE_{CMD,TASK} requests and move it to ide_tf_load()
  so it also covers REQ_ATA_TYPE_TASKFILE requests.

There should be no functionality changes caused by this patch
(unless DEBUG is defined).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove ide_cmd() helper.

* Clear nIEN and call SELECT_MASK() before writing taskfile registers.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename 'args' variable in 'if (rq->cmd_type == REQ_TYPE_ATA_TASKFILE)'
  block to 'task'.

* execute_drive_cmd() is used only for REQ_TYPE_ATA_{CMD,TASK,TASKFILE} so
  we can move the common code out from 'if (rq->cmd_type == REQ_TYPE_ATA_CMD)'
  and 'if (rq->cmd_type == REQ_TYPE_ATA_TASK)' blocks.

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move loading of IDE_NSECTOR_REG from ide_cmd() to execute_drive_cmd()
(load the IDE_NSECTOR_REG just after IDE_FEATURE_REG).

This also allows us to drop 'nsect' argument from ide_cmd() and simplify
execute_drive_cmd() code for REQ_TYPE_ATA_CMD case a bit.

It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix registers loading order for REQ_TYPE_ATA_CMD request with WIN_SMART
command in execute_drive_cmd() (load IDE_FEATURE_REG and IDE_SECTOR_REG
before loading IDE_LCYL_REG and IDE_HCYL_REG).

It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove stale ide.h "configuration options":

* INITIAL_MULT_COUNT - always defined to 0

* SUPPORT_SLOW_DATA_PORTS - unused

* OK_TO_RESET_CONTROLLER - always defined to 1

* DISABLE_IRQ_NOSYNC - always defined to 0

Leave SUPPORT_VLB_SYNC (defined to 0 for CRIS and FRV, otherwise to 1)
for now but disallow overriding it by <asm/ide.h>.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

We can safely remove CONFIG_IDEPCI_SHARE_IRQ and always support
PCI IRQ sharing.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

IRQF_DISABLED is not needed because the first thing that ide_intr()
(IDE IRQ handler) does is calling spin_lock_irqsave() which disables
local IRQs (IRQ unmasking is later handled by drive->unmask).

kernel/irq/handle.c:

irqreturn_t handle_IRQ_event(unsigned int irq, struct irqaction *action)
...
	if (!(action->flags & IRQF_DISABLED))
		local_irq_enable_in_hardirq();

	do {
		ret = action->handler(irq, action->dev_id);
		if (ret == IRQ_HANDLED)
			status |= action->flags;
		retval |= ret;
		action = action->next;
	} while (action);
...

drivers/ide/ide-io.c:

irqreturn_t ide_intr (int irq, void *dev_id)
...
	spin_lock_irqsave(&ide_lock, flags);
...
	spin_unlock(&ide_lock);
...
	if (drive->unmask)
		local_irq_enable_in_hardirq();
...
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* pmac_ide_init_hwif_ports() can be called by ide_init_hwif_ports()
  (through ppc_ide_md.ide_init_hwif hook) for non IDE PMAC interfaces.
  If this is the case the hw->io_ports[] should be already setup by
  ide_init_hwif_ports()->ide_std_init_ports() so remove redundant code
  from pmac_ide_init_hwif_ports().

  As side-effect this change fixes ctl_addr == 0 special handling in
  ide_init_hwif_ports().

* Fix misleading comment while at it.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Based on the earlier work by Tejun Heo.

* Move setting IDE_TFLAG_LBA48 taskfile flag from do_rw_taskfile()
  function to the callers.

* Add IDE_TFLAG_FLAGGED taskfile flag for flagged taskfiles coming
  from ide_taskfile_ioctl().  Check it instead of ->tf_out_flags.all.

* Add IDE_TFLAG_OUT_DATA taskfile flag to indicate the need to load
  IDE data register in ide_tf_load().

* Add IDE_TFLAG_OUT_* taskfile flags to indicate the need to load
  particular IDE taskfile registers in ide_tf_load().

* Update do_rw_taskfile() and ide_tf_load() users to set respective
  IDE_TFLAG_OUT_* taksfile flags.

* Add task_dma_ok() helper.

* Use IDE_TFLAG_FLAGGED taskfile flag to select HIHI mask in ide_tf_load().

* Use do_rw_taskfile() in flagged_taskfile().

* Remove no longer needed 'tf_out_flags' field from ide_task_t.

There should be no functionality changes caused by this patch.

Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ide_no_data_taskfile() helper and convert ide_raw_taskfile() w/ NO DATA
  protocol users to use it instead.

* Set ->data_phase explicitly in ide_no_data_taskfile()
  (TASKFILE_NO_DATA is defined as 0x0000).

* Unexport task_no_data_intr().
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Based on the earlier work by Tejun Heo.

* Add 'tf_flags' field (for taskfile flags) to ide_task_t.

* Add IDE_TFLAG_LBA48 taskfile flag for LBA48 taskfiles.

* Add IDE_TFLAG_NO_SELECT_MASK taskfile flag for __ide_do_rw_disk()
  which doesn't use SELECT_MASK() (looks like a bug but it requires
  some more investigation).

* Split off ide_tf_load() helper from do_rw_taskfile().

* Convert __ide_do_rw_disk() to use ide_tf_load().

There should be no functionality changes caused by this patch.

Cc: Tejun Heo <htejun@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Based on the earlier work by Tejun Heo.

There should be no functionality changes caused by this patch.

Cc: Tejun Heo <htejun@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Load IDE_SECTOR_REG after IDE_FEATURE_REG and IDE_NSECTOR_REG when using CHS.

This patch is basically a preparation for the next one which converts
__ide_do_rw_disk() to use struct ide_taskfile.

It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Merge idedisk_{read_native,set}_max_address_ext() into
  idedisk_{read_native,set}_max_address().

v2:
* Remove LBA48 code leftover from idedisk_read_native_max_address()
  ('high' variable initialization).  (Noticed by Sergei).

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Don't set write-only ide_task_t.hobRegister[6] and ide_task_t.hobRegister[7]
  in idedisk_set_max_address_ext().

* Add struct ide_taskfile and use it in ide_task_t instead of tfRegister[]
  and hobRegister[].

* Remove no longer needed IDE_CONTROL_OFFSET_HOB define.

* Add #ifndef/#endif __KERNEL__ around definitions of {task,hob}_struct_t.

While at it:

* Use ATA_LBA define for LBA bit (0x40) as suggested by Tejun Heo.

v2:
* Add missing newlines. (Noticed by Sergei)

* Use ~ATA_LBA instead of 0xBF. (Noticed by Sergei)

* Use unnamed unions for error/feature and status/command.
  (Suggested by Sergei).

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove task_ioreg_t typedef from the kernel code (but leave it
in <linux/hdreg.h> for #ifndef/#endif __KERNEL__ case).

While at it also move sata_ioreg_t typedef under #ifndef/#endif __KERNEL__.

v2:
Remove name of the second parameter from ide_execute_command() declaration.
(Noticed by Sergei).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Convert cmd64x, hpt366 and pdc202xx_old host drivers to use
  pci_resource_start(hwif->pci_dev, 4) instead of hwif->dma_master.

* Remove no longer needed ->dma_master field from ide_hwif_t.

v2:
* Use the more readable 'hwif->dma_base - (hwif->channel * 8)' instead of
  pci_resource_start(hwif->pci_dev, 4).

v3:
* Use hwif->extra_base in hpt366/pdc20xx_old + some cosmetic fixups over v2
  (suggested by Sergei).

v4:
* Correct offsets in hpt3xxn_set_clock().

v5:
* Use hwif->extra_base in hpt366 for _real_ this time. (Noticed by Sergei)
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Group the array of pointers to the timing tables with the timing register masks
which allows us to merge HPT36x/HPT37x set_dma_mode() methods into one.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There's no reason to keep the set_dma_mode() method wrapper for two different
chip families, so get rid of it...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Since PIO autotuning is now done always, there's no need anymore to program
the taskfile timings also on DMA modes, so change the IDE timing register
masks accordingly, "inverting the polarity" of the masks while at it...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Currently it's possible to ide-cd to set an incorrect blocksize by
reading garbage if the drive is dead:

ide_cd_probe()
 -> cdrom_read_toc()
     -> cdrom_read_capacity()
         -> cdrom_queue_packet_command()
             -> ide_do_drive_cmd()
                 -> ide_do_request()
                     -> start_request()

on start_request():

        /* bail early if we've exceeded max_failures */
        if (drive->max_failures && (drive->failures > drive->max_failures)) {
                goto kill_rq;
        }
(...)
kill_rq:
        ide_kill_rq(drive, rq);
        return ide_stopped;

ide_kill_rq() and the next calls won't set REQ_FAILED on rq->cmd_flags and thus
cdrom_queue_packet_command() won't return an error. then:

        stat = cdrom_queue_packet_command(drive, &req);
        if (stat == 0) {
                *capacity = 1 + be32_to_cpu(capbuf.lba);
                *sectors_per_frame =
                        be32_to_cpu(capbuf.blocklen) >> SECTOR_BITS;
        }

cdrom_read_capacity() ends believing capbuf is valid but in fact it's just
uninitialized data. back to cdrom_read_toc():

        /* Try to get the total cdrom capacity and sector size. */
        stat = cdrom_read_capacity(drive, &toc->capacity, &sectors_per_frame,
                                   sense);
        if (stat)
                toc->capacity = 0x1fffff;

        set_capacity(info->disk, toc->capacity * sectors_per_frame);
        /* Save a private copy of te TOC capacity for error handling */
        drive->probed_capacity = toc->capacity * sectors_per_frame;

        blk_queue_hardsect_size(drive->queue,
                                sectors_per_frame << SECTOR_BITS);

that will set drive->queue->hardsect_size to be the random value.
hardsect_size is used to calculate inode->i_blkbits. later on, on a read
path:

void create_empty_buffers(struct page *page,
                        unsigned long blocksize, unsigned long b_state)
{       
        struct buffer_head *bh, *head, *tail;

        head = alloc_page_buffers(page, blocksize, 1);
        bh = head;
        do {    
                bh->b_state |= b_state;
                tail = bh;
                bh = bh->b_this_page;
        } while (bh);
        tail->b_this_page = head;

alloc_page_buffers() will return NULL if blocksize > 4096. blocksize is
calculed based on inode->i_blkbits. that will trigger a null
dereference on create_empty_buffers().
Signed-off-by: NAristeu Rozanski <arozansk@redhat.com>
Cc: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
  selinux: make mls_compute_sid always polyinstantiate
  security/selinux: constify function pointer tables and fields
  security: add a secctx_to_secid() hook
  security: call security_file_permission from rw_verify_area
  security: remove security_sb_post_mountroot hook
  Security: remove security.h include from mm.h
  Security: remove security_file_mmap hook sparse-warnings (NULL as 0).
  Security: add get, set, and cloning of superblock security information
  security/selinux: Add missing "space"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  [AVR32] extint: Set initial irq type to low level
  [AVR32] extint: change set_irq_type() handling
  [AVR32] NMI debugging
  [AVR32] constify function pointer tables
  [AVR32] ATNGW100: Update defconfig
  [AVR32] ATSTK1002: Update defconfig
  [AVR32] Kconfig: Choose daughterboard instead of CPU
  [AVR32] Add support for ATSTK1003 and ATSTK1004
  [AVR32] Clean up external DAC setup code
  [AVR32] ATSTK1000: Move gpio-leds setup to setup.c
  [AVR32] Add support for AT32AP7001 and AT32AP7002
  [AVR32] Provide more CPU information in /proc/cpuinfo and dmesg
  [AVR32] Oprofile support
  [AVR32] Include instrumentation menu
  Disable VGA text console for AVR32 architecture
  [AVR32] Enable debugging only when needed
  ptrace: Call arch_ptrace_attach() when request=PTRACE_TRACEME
  [AVR32] Remove redundant try_to_freeze() call from do_signal()
  [AVR32] Drop GFP_COMP for DMA memory allocations

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw: (56 commits)
  [GFS2] Allow journal recovery on read-only mount
  [GFS2] Lockup on error
  [GFS2] Fix page_mkwrite truncation race path
  [GFS2] Fix typo
  [GFS2] Fix write alloc required shortcut calculation
  [GFS2] gfs2_alloc_required performance
  [GFS2] Remove unneeded i_spin
  [GFS2] Reduce inode size by moving i_alloc out of line
  [GFS2] Fix assert in log code
  [GFS2] Fix problems relating to execution of files on GFS2
  [GFS2] Initialize extent_list earlier
  [GFS2] Allow page migration for writeback and ordered pages
  [GFS2] Remove unused variable
  [GFS2] Fix log block mapper
  [GFS2] Minor correction
  [GFS2] Eliminate the no longer needed sd_statfs_mutex
  [GFS2] Incremental patch to fix compiler warning
  [GFS2] Function meta_read optimization
  [GFS2] Only fetch the dinode once in block_map
  [GFS2] Reorganize function gfs2_glmutex_lock
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (125 commits)
  [CRYPTO] twofish: Merge common glue code
  [CRYPTO] hifn_795x: Fixup container_of() usage
  [CRYPTO] cast6: inline bloat--
  [CRYPTO] api: Set default CRYPTO_MINALIGN to unsigned long long
  [CRYPTO] tcrypt: Make xcbc available as a standalone test
  [CRYPTO] xcbc: Remove bogus hash/cipher test
  [CRYPTO] xcbc: Fix algorithm leak when block size check fails
  [CRYPTO] tcrypt: Zero axbuf in the right function
  [CRYPTO] padlock: Only reset the key once for each CBC and ECB operation
  [CRYPTO] api: Include sched.h for cond_resched in scatterwalk.h
  [CRYPTO] salsa20-asm: Remove unnecessary dependency on CRYPTO_SALSA20
  [CRYPTO] tcrypt: Add select of AEAD
  [CRYPTO] salsa20: Add x86-64 assembly version
  [CRYPTO] salsa20_i586: Salsa20 stream cipher algorithm (i586 version)
  [CRYPTO] gcm: Introduce rfc4106
  [CRYPTO] api: Show async type
  [CRYPTO] chainiv: Avoid lock spinning where possible
  [CRYPTO] seqiv: Add select AEAD in Kconfig
  [CRYPTO] scatterwalk: Handle zero nbytes in scatterwalk_map_and_copy
  [CRYPTO] null: Allow setkey on digest_null 
  ...

This can be broken down into these major areas:
 - Documentation updates (language translations and fixes, as
   well as kobject and kset documenatation updates.)
 - major kset/kobject/ktype rework and fixes.  This cleans up the
   kset and kobject and ktype relationship and architecture,
   making sense of things now, and good documenation and samples
   are provided for others to use.  Also the attributes for
   kobjects are much easier to handle now.  This cleaned up a LOT
   of code all through the kernel, making kobjects easier to use
   if you want to.
 - struct bus_type has been reworked to now handle the lifetime
   rules properly, as the kobject is properly dynamic.
 - struct driver has also been reworked, and now the lifetime
   issues are resolved.
 - the block subsystem has been converted to use struct device
   now, and not "raw" kobjects.  This patch has been in the -mm
   tree for over a year now, and finally all the issues are
   worked out with it.  Older distros now properly work with new
   kernels, and no userspace updates are needed at all.
 - nozomi driver is added.  This has also been in -mm for a long
   time, and many people have asked for it to go in.  It is now
   in good enough shape to do so.
 - lots of class_device conversions to use struct device instead.
   The tree is almost all cleaned up now, only SCSI and IB is the
   remaining code to fix up...

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (196 commits)
  Driver core: coding style fixes
  Kobject: fix coding style issues in kobject c files
  Kobject: fix coding style issues in kobject.h
  Driver core: fix coding style issues in device.h
  spi: use class iteration api
  scsi: use class iteration api
  rtc: use class iteration api
  power supply : use class iteration api
  ieee1394: use class iteration api
  Driver Core: add class iteration api
  Driver core: Cleanup get_device_parent() in device_add() and device_move()
  UIO: constify function pointer tables
  Driver Core: constify the name passed to platform_device_register_simple
  driver core: fix build with SYSFS=n
  sysfs: make SYSFS_DEPRECATED depend on SYSFS
  Driver core: use LIST_HEAD instead of call to INIT_LIST_HEAD in __init
  kobject: add sample code for how to use ksets/ktypes/kobjects
  kobject: add sample code for how to use kobjects in a simple manner.
  kobject: update the kobject/kset documentation
  kobject: remove old, outdated documentation.
  ...

If the node we're booting on doesn't have memory, bootstrapping kmalloc()
caches resorts to fallback_alloc() which requires ->nodelists set for all
nodes.  Fix that by calling set_up_list3s() for CACHE_CACHE in
kmem_cache_init().

As kmem_getpages() is called with GFP_THISNODE set, this used to work before
because of breakage in 2.6.22 and before with GFP_THISNODE returning pages from
the wrong node if a node had no memory. So it may have worked accidentally and
in an unsafe manner because the pages would have been associated with the wrong
node which could trigger bug ons and locking troubles.
Tested-by: NMel Gorman <mel@csn.ul.ie>
Tested-by: NOlaf Hering <olaf@aepfle.de>
Reviewed-by: NChristoph Lameter <clameter@sgi.com>
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>
[ With additional one-liner by Olaf Hering  - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix overwriting the stack with the version string
(it is currently 10 bytes + zero) when unloading the
capidrv module. Safeguard against overwriting it
should the version string grow in the future.

Should fix Kernel Bug Tracker Bug 9696.
Signed-off-by: NGerd v. Egidy <gerd.von.egidy@intra2net.com>
Acked-by: NKarsten Keil <kkeil@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch allows gfs2 to perform journal recovery even if it is mounted
read-only. Strictly speaking, a read-only mount should not be writing to
the filesystem, but we do this only to perform journal recovery. A
read-only mount will fail if we don't recover the dirty journal. Also,
when gfs2 is used as a root filesystem, it will be mounted read-only
before being mounted read-write during the boot sequence. A failed
read-only mount will panic the machine during bootup.
Signed-off-by: NAbhijith Das <adas@redhat.com>
Signed-off-by: NSteven Whitehouse <swhiteho@redhat.com>

I spotted this bug while I was digging around.  Looks like it could cause
a lockup in some rare error condition.
Signed-off-by: NBob Peterson <rpeterso@redhat.com>
Signed-off-by: NSteven Whitehouse <swhiteho@redhat.com>

There was a bug in the truncation/invalidation race path for
->page_mkwrite for gfs2. It ought to return 0 so that the effect is the
same as if the page was truncated at any of the other points at which
the page_lock is dropped. This will result in the restart of the whole
page fault path. If it was due to a real truncation (as opposed to an
invalidate because we let a glock go) then the ->fault path will pick
that up when it gets called again.
Signed-off-by: NSteven Whitehouse <swhiteho@redhat.com>

This patch fixes a minor typo.  Surprisingly, it still compiled.
Signed-off-by: NBob Peterson <rpeterso@redhat.com>
Signed-off-by: NSteven Whitehouse <swhiteho@redhat.com>

The comparison was being made against the wrong quantity.
Signed-off-by: NSteven Whitehouse <swhiteho@redhat.com>