Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 05 6月, 2014 2 次提交
    • V
      bonding: Support macvlans on top of tlb/rlb mode bonds · 14af9963
      由 Vlad Yasevich 提交于 
      To make TLB mode work, the patch allows learning packets
to be sent using mac addresses assigned to macvlan devices,
also taking into an account vlans that may be between the
bond and macvlan device.

To make RLB work, all we have to do is accept ARP packets
for addresses added to the bond dev->uc list.  Since RLB
mode will take care to update the peers directly with
correct mac addresses, learning packets for these addresses
do not have be send to switch.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      14af9963
    • V
      bonding: Turn on IFF_UNICAST_FLT on bond devices · c565b488
      由 Vlad Yasevich 提交于 
      Bonding devices manage the unicast filters of the underlying
interfaces, but do not turn on IFF_UNICAST_FLT flag.  Thus
anytime a unicast address is added to the bond, the bond is
places in promiscuous mode.

Turn on IFF_UNICAST_FLT on the bond device so that the bond does
not go into promiscuous mode needlesly.  If an underlying device
does not support unicast filtering, that device will automaticall
enter promiscuous mode already.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c565b488
  3. 23 5月, 2014 2 次提交
  5. 17 5月, 2014 9 次提交
  7. 15 5月, 2014 1 次提交
  9. 09 5月, 2014 1 次提交
  11. 25 4月, 2014 3 次提交
    • M
      bonding: Add tlb_dynamic_lb parameter for tlb mode · e9f0fb88
      由 Mahesh Bandewar 提交于 
      The aggresive load balancing causes packet re-ordering as active
flows are moved from a slave to another within the group. Sometime
this aggresive lb is not necessary if the preference is for less
re-ordering. This parameter if used with value "0" disables
this dynamic flow shuffling minimizing packet re-ordering. Of course
the side effect is that it has to live with the static load balancing
that the hashing distribution provides. This impact is less severe if
the correct xmit-hashing-policy is used for the tlb setup.

The default value of the parameter is set to "1" mimicing the earlier
behavior.

Ran the netperf test with 200 stream for 1 min between two hosts with
4x1G trunk (xmit-lb mode with xmit-policy L3+4) before and after these
changes. Following was the command used for those 200 instances -

    netperf -t TCP_RR -l 60 -s 5 -H <host> -- -r81920,81920

Transactions per second:
    Before change: 1,367.11
    After  change: 1,470.65

Change-Id: Ie3f75c77282cf602e83a6e833c6eb164e72a0990
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e9f0fb88
    • M
      bonding: Added bond_tlb_xmit() for tlb mode. · f05b42ea
      由 Mahesh Bandewar 提交于 
      Re-organized the xmit function for the lb mode separating tlb xmit
from the alb mode. This will enable use of the hashing policies
like 802.3ad mode. Also extended use of xmit-hash-policy to tlb mode.

Now the tlb-mode defaults to BOND_XMIT_POLICY_LAYER2 if the xmit policy
module parameter is not set (just like 802.3ad, or Xor mode).

Change-Id: I140257403d272df75f477b380207338d0f04963e
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f05b42ea
    • M
      bonding: Changed hashing function to just provide hash · ee62e868
      由 Mahesh Bandewar 提交于 
      Modified the hash function to return just hash separating from the
modulo operation that can be performed by the caller. This is to
make way for the tlb mode to use the same hashing policies that
are used in the 802.3ad and Xor mode.

Change-Id: I276609e87e0ca213c4d1b17b79c5e0b0f3d0dd6f
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ee62e868
  13. 12 4月, 2014 1 次提交
  15. 04 4月, 2014 1 次提交
    • Z
      bonding: Inactive slaves should keep inactive flag's value · 7db8df02
      由 zheng.li 提交于 
      bond_open is not setting the inactive flag correctly for some modes (alb and
tlb), resulting in error behavior if the bond has been administratively set
down and then back up. This effect should not occur when slaves are added while
the bond is up; it's something that only happens after a down/up bounce of the
bond.

For example, in bond tlb or alb mode, domu send some ARP request which go out
from dom0 bond's active slave, then the ARP broadcast request packets go back to
inactive slave from switch, because the inactive slave's inactive flag is zero,
kernel will receive the packets and pass them to bridge that cause dom0's bridge
map domu's MAC address to port of bond, bridge should map domu's MAC to port of
vif.
Signed-off-by: NZheng Li <zheng.x.li@oracle.com>
Signed-off-by: NJay Vosburgh <j.vosburgh@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7db8df02
  17. 30 3月, 2014 1 次提交
  19. 27 3月, 2014 4 次提交
    • D
      bonding: add net_ratelimt to avoid spam in arp interval · 4873ac3c
      由 dingtianhong 提交于 
      Remove the unnecessary log and add net_ratelimit to the others, in order to
avoid spam the log.

Cc: Joe Perches <joe@perches.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4873ac3c
    • D
      bonding: support QinQ for bond arp interval · fbd929f2
      由 dingtianhong 提交于 
      The bond send arp request to indicate that the slave is active, and if the bond dev
is a vlan dev, it will set the vlan tag in skb to notice the vlan group, but the
bond could only send a skb with 802.1q proto, not support for QinQ.

So add outer tag for lower vlan tag and inner tag for upper vlan tag to support QinQ,
The new skb will be consist of two vlan tag just like this:

dst mac | src mac | outer vlan tag | inner vlan tag | data | .....

If We don't need QinQ, the inner vlan tag could be set to 0 and use outer vlan tag
 as a normal vlan group.

Using "ip link" to configure the bond for QinQ and add test log:

ip link add link bond0  bond0.20 type vlan proto 802.1ad id 20
ip link add link bond0.20  bond0.20.200 type vlan proto 802.1q id 200

ifconfig bond0.20 11.11.20.36/24
ifconfig bond0.20.200 11.11.200.36/24

echo +11.11.200.37 > /sys/class/net/bond0/bonding/arp_ip_target

90:e2:ba:07:4a:5c (oui Unknown) > Broadcast, ethertype 802.1Q-QinQ (0x88a8),length 50: vlan 20, p 0,ethertype 802.1Q, vlan 200, p 0, ethertype ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 11.11.200.37 tell 11.11.200.36, length 28

90:e2:ba:06:f9:86 (oui Unknown) > 90:e2:ba:07:4a:5c (oui Unknown), ethertype 802.1Q-QinQ (0x88a8), length 50: vlan 20, p 0, ethertype 802.1Q, vlan 200, p 0, ethertype ARP, Ethernet (len 6), IPv4 (len 4), Reply 11.11.200.37 is-at 90:e2:ba:06:f9:86 (oui Unknown), length 28

v1->v2: remove the comment "TODO: QinQ?".

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      fbd929f2
    • D
      bonding: ratelimit pr_err() for bond xmit broadcast · 9152e26d
      由 dingtianhong 提交于 
      It may spam if the system is out of the memory, add ratelimit for it.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      9152e26d
    • D
      bonding: slight optimization for bond xmit path · 054bb880
      由 dingtianhong 提交于 
      Add unlikely() micro to the unlikely conditions in the bond
xmit path for slight optimization.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      054bb880
  21. 13 3月, 2014 1 次提交
  23. 07 3月, 2014 2 次提交
  25. 03 3月, 2014 1 次提交
    • V
      bonding: send arp requests even if there's no route to them · 28572760
      由 Veaceslav Falico 提交于 
      Currently we're only sending arp requests if we have a route to the target
(and, thus, can find out the source ip address).

There are some use cases, however, where we don't want/need to set an ip
address (or set up a specific route) for bonding to use arp monitoring *for
traffic generation*. We can easily send arp probes (arp requests with src
ip == 0) to generate arp broadcast responses from the target ip and use
them for determining if the target is up.

This, obviously, won't work with arp validation - because we don't have the
ip address set and, thus, will filter out the responses. So in that case -
print a warning.

CC: François CACHEREUL <f.cachereul@alphalink.fr>
CC: Zhenjie Chen <zhchen@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      28572760
  27. 27 2月, 2014 4 次提交
    • J
      bonding: disallow enslaving a bond to itself · 09a89c21
      由 Jiri Bohac 提交于 
      Enslaving a bond to itself leads to an endless loop and hangs the kernel.
Signed-off-by: NJiri Bohac <jbohac@suse.cz>
Tested-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      09a89c21
    • N
      bonding: fix a div error caused by the slave release path · ee6154e1
      由 Nikolay Aleksandrov 提交于 
      There's a bug in the slave release function which leads the transmit
functions which use the bond->slave_cnt to a div by 0 because we might
just have released our last slave and made slave_cnt == 0 but at the same
time we may have a transmitter after the check for an empty list which will
fetch it and use it in the slave id calculation.
Fix it by moving the slave_cnt after synchronize_rcu so if this was our
last slave any new transmitters will see an empty slave list which is
checked after rcu lock but before calling the mode transmit functions
which rely on bond->slave_cnt.

Fixes: 278b2083 ("bonding: initial RCU conversion")

CC: Veaceslav Falico <vfalico@redhat.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Acked-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ee6154e1
    • D
      bonding: Fix RTNL: assertion failed at net/core/rtnetlink.c for ab arp monitor · b0929915
      由 dingtianhong 提交于 
      Veaceslav has reported and fix this problem by commit f2ebd477
(bonding: restructure locking of bond_ab_arp_probe()). According Jay's
opinion, the current solution is not very well, because the notification
is to indicate that the interface has actually changed state in a meaningful
way, but these calls in the ab ARP monitor are internal settings of the flags
to allow the ARP monitor to search for a slave to become active when there are
no active slaves. The flag setting to active or backup is to permit the ARP
monitor's response logic to do the right thing when deciding if the test
slave (current_arp_slave) is up or not.

So the best way to fix the problem is that we should not send a notification
when the slave is in testing state, and check the state at the end of the
monitor, if the slave's state recover, avoid to send pointless notification
twice. And RTNL is really a big lock, hold it regardless the slave's state
changed or not when the current_active_slave is null will loss performance
(every 100ms), so we should hold it only when the slave's state changed and
need to notify.

I revert the old commit and add new modifications.

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b0929915
    • D
      bonding: Fix RTNL: assertion failed at net/core/rtnetlink.c for 802.3ad mode · 5e5b0665
      由 dingtianhong 提交于 
      The problem was introduced by the commit 1d3ee88a
(bonding: add netlink attributes to slave link dev).
The bond_set_active_slave() and bond_set_backup_slave()
will use rtmsg_ifinfo to send slave's states, so these
two functions should be called in RTNL.

In 802.3ad mode, acquiring RTNL for the __enable_port and
__disable_port cases is difficult, as those calls generally
already hold the state machine lock, and cannot unconditionally
call rtnl_lock because either they already hold RTNL (for calls
via bond_3ad_unbind_slave) or due to the potential for deadlock
with bond_3ad_adapter_speed_changed, bond_3ad_adapter_duplex_changed,
bond_3ad_link_change, or bond_3ad_update_lacp_rate.  All four of
those are called with RTNL held, and acquire the state machine lock
second.  The calling contexts for __enable_port and __disable_port
already hold the state machine lock, and may or may not need RTNL.

According to the Jay's opinion, I don't think it is a problem that
the slave don't send notify message synchronously when the status
changed, normally the state machine is running every 100 ms, send
the notify message at the end of the state machine if the slave's
state changed should be better.

I fix the problem through these steps:

1). add a new function bond_set_slave_state() which could change
    the slave's state and call rtmsg_ifinfo() according to the input
    parameters called notify.

2). Add a new slave parameter which called should_notify, if the slave's state
    changed and don't notify yet, the parameter will be set to 1, and then if
    the slave's state changed again, the param will be set to 0, it indicate that
    the slave's state has been restored, no need to notify any one.

3). the __enable_port and __disable_port should not call rtmsg_ifinfo
    in the state machine lock, any change in the state of slave could
    set a flag in the slave, it will indicated that an rtmsg_ifinfo
    should be called at the end of the state machine.

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5e5b0665
  29. 25 2月, 2014 2 次提交
  31. 21 2月, 2014 1 次提交
  33. 20 2月, 2014 1 次提交
  35. 19 2月, 2014 3 次提交