Request for comment and commit.

From: T. Mehnert <t.mehnert@eckelmann.de>
Date: Mon, 4 Jul 2011 15:53:30 +0200
Subject: [PATCH] i.MX25 GPT clock fix: ensure correct the clock source

This patch ensures, that Linux will take the correct clock source (AHB_DIV)
for gpt in the ARM i.MX25 implementation. The currect code depends on the reset
defaults of the CCM_MCR register. So on some boards it could happen that the
UPLL is used for clock source, which results in faulty time behavior in Linux.
In this case all delays or sleeps will will be faktor 1.8 too long.
Signed-off-by: NTorsten Mehnert <t.mehnert@eckelmann.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

It might be not good to use software defined version to identify sdma
device type, when hardware does not define such version.  Instead,
soc name is stable enough to define the device type.

The patch uses platform_device_id rather than version number passed
by platform data to identify sdma device type/version.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NVinod Koul <vinod.koul@intel.com>

The patch removes all the uses of cpu_is_mx().  Instead, it utilizes
platform_device_id to distinguish the esdhc differences among SoCs.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NChris Ball <cjb@laptop.org>

On the recent i.mx (mx25/50/53), there is a gasket inside fec
controller which needs to be enabled no matter phy works in MII
or RMII mode.

The current code enables the gasket only when phy interface is RMII.
It's broken when the driver works with a MII phy.  The patch uses
platform_device_id to distinguish the SoCs that have the gasket and
enables it on these SoCs for both MII and RMII mode.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Reported-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: NDavid S. Miller <davem@davemloft.net>

The patch removes all the uses of cpu_is_mx1().  Instead, it uses
the .id_table of platform_driver to distinguish the uart device type,
IMX1_UART and IMX21_UART.  The IMX21_UART type runs on all i.mx
except i.mx1.

A couple of !cpu_is_mx1 logic gets turned into is_imx21_uart,
as the codes wrapped there are really IMX21 type uart specific.

It also removes macro MX1_UCR3_REF25 and MX1_UCR3_REF30 which are
not used anywhere.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

Software defined version number is not stable enough to be used
in device type naming scheme.  The patch changes it to use implicit
soc name for spi device type definition.  In this way, we can easily
align the naming scheme with device tree binding, which comes later.

It removes fifosize from spi_imx_data and adds devtype there, so that
fifosize can be set in an inline function according to devtype.
Also, cpu_is_mx can be replaced by inline functions checking devtype.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Use clk_get to acquire the watchdog clock and also avoid hardcoding the clock name.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

* get_rate_arm : when 400MHz clock is selected (cctl & 1<<14),
ARM clock is 400MHz (MPLL * 3 / 4) and not 800MHz
* get_rate_per : peripherals's clock is derived from AHB and not
from IPG (ref manual : figure 5-1)
* can2_clk : use the correct ID

* without this patch, peripherals getting their clock from PER
clocks work fine because of the 2 errors which fix themselves
(ARM clock x 2 and per clock actually based on IPG which is AHB/2)
but flexcan can't work as it gets its clock from IPG and thus
calculates its bitrate using a reference value which is twice
what it really is.
Signed-off-by: NEric Bénard <eric@eukrea.com>

So the correct clock will be taken for each of the two independent
controllers.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The driver recently learned to handle platform ids.  Make use of this
new feature.  The up side is that the driver needs less knowledge about
the spi interfaces used on different SoCs.
Acked-by: NJason Wang <jason77.wang@gmail.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

DEBUG_LL is actually broken on i.MX25, this patch fix it.
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The information in the i.MX25 Reference Manual is lacking. Add information from
the Freescale BSP.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

* add clocks for audmux and ssi 1 & 2
* add irq for ssi 1 & 2
* add devices platform for ssi1 & 2
* update audmux-v2 for i.MX25
* add base addresses for audmux & ssi 1 & 2
* add iomux configuration for GPIO for AUD5 port
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

usb drivers need to get the right value for otg clock so
calculate and return it
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Most machine classes want some way to register a block of clk_lookup
structures, and most do it by implementing a clks_register() type
function which walks an array, or by open-coding a loop.

Consolidate all this into clkdev_add_table().
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: NKevin Hilman <khilman@deeprootsystems.com>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This makes the FEC clock configuration consistent with the UART one.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The gpt_clk rate function doesn't consider the PER divider. This causes a
significant drift in time accounting. Fix this by introducing the correct rate
calculation function.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch disables all unnecessary clock in mx25_clocks_init() to make a clean
start, the same as is being done for the rest of the i.MX chips.

This patch was tested on i.MX25 PDK.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The fref is needless on mx25 since the reference clock is fixed at 24MHz.
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

For uarts and fec need two clocks, implement it using the secondary clock
field in struct clk.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>