When trying to delete a table >= 256 using iproute2 the local table
will be deleted.
The table id is specified as a netlink attribute when it needs more then
8 bits and iproute2 then sets the table field to RT_TABLE_UNSPEC (0).
Preconditions to matching the table id in the rule delete code
doesn't seem to take the "table id in netlink attribute" into condition
so the frh_get_table helper function never gets to do its job when
matching against current rule.
Use the helper function twice instead of peaking at the table value directly.

Originally reported at: http://bugs.debian.org/724783Reported-by: NNicolas HICHER <nhicher@avencall.com>
Signed-off-by: NAndreas Henriksson <andreas@fatal.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Take ip6_fl_lock before to read and update
a label.

v2: protect only the relevant code
Reported-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NFlorent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the last RFC 6437 does not give any constraints
for lifetime of flow labels, the previous RFC 3697
spoke of a minimum of 120 seconds between
reattribution of a flow label.

The maximum linger is currently set to 60 seconds
and does not allow this configuration without
CAP_NET_ADMIN right.

This patch increase the maximum linger to 150
seconds, allowing more flexibility to standard
users.
Signed-off-by: NFlorent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is already possible to set/put/renew a label
with IPV6_FLOWLABEL_MGR and setsockopt. This patch
add the possibility to get information about this
label (current value, time before expiration, etc).

It helps application to take decision for a renew
or a release of the label.

v2:
 * Add spin_lock to prevent race condition
 * return -ENOENT if no result found
 * check if flr_action is GET

v3:
 * move the spin_lock to protect only the
   relevant code
Signed-off-by: NFlorent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By moving code around, we avoid :

1) A reload of iph->ihl (bit field, so needs a mask)

2) A conditional test (replaced by a conditional mov on x86)
   Fast path loads iph->protocol anyway.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While testing virtio_net and skb_segment() changes, Hannes reported
that UFO was sending wrong frames.

It appears this was introduced by a recent commit :
8c3a897b ("inet: restore gso for vxlan")

The old condition to perform IP frag was :

tunnel = !!skb->encapsulation;
...
        if (!tunnel && proto == IPPROTO_UDP) {

So the new one should be :

udpfrag = !skb->encapsulation && proto == IPPROTO_UDP;
...
        if (udpfrag) {

Initialization of udpfrag must be done before call
to ops->callbacks.gso_segment(skb, features), as
skb_udp_tunnel_segment() clears skb->encapsulation

(We want udpfrag to be true for UFO, false for VXLAN)

With help from Alexei Starovoitov
Reported-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use "@" to refer to parameters in the kernel-doc description. According
to Documentation/kernel-doc-nano-HOWTO.txt "&" shall be used to refer to
structures only.
Signed-off-by: NMathias Krause <mathias.krause@secunet.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also remove the warning for fragmented packets -- skb_cow_data() will
linearize the buffer, removing all fragments.
Signed-off-by: NMathias Krause <mathias.krause@secunet.com>
Cc: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function has usage beside IPsec so move it to the core skbuff code.
While doing so, give it some documentation and change its return type to
'unsigned char *' to be in line with skb_put().
Signed-off-by: NMathias Krause <mathias.krause@secunet.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a operations structure that allows a network interface to export
the fact that it supports package forwarding in hardware between
physical interfaces and other mac layer devices assigned to it (such
as macvlans). This operaions structure can be used by virtual mac
devices to bypass software switching so that forwarding can be done
in hardware more efficiently.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We recently added a new error path and it needs a dev_put().

Fixes: 7adac1ec ('6lowpan: Only make 6lowpan links to IEEE802154 devices')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide a method for read-only access to the vlan device egress mapping.

Do this by refactoring vlan_dev_get_egress_qos_mask() such that now it
receives as an argument the skb priority instead of pointer to the skb.

Such an access is needed for the IBoE stack where the control plane
goes through the network stack. This is an add-on step on top of commit
d4a96865 "net/route: export symbol ip_tos2prio" which allowed the RDMA-CM
to use ip_tos2prio.
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If appending a received fragment to the pending fragment chain
in a unicast link fails, the current code tries to force a retransmission
of the fragment by decrementing the 'next received sequence number'
field in the link. This is done under the assumption that the failure
is caused by an out-of-memory situation, an assumption that does
not hold true after the previous patch in this series.

A failure to append a fragment can now only be caused by a protocol
violation by the sending peer, and it must hence be assumed that it
is either malicious or buggy.  Either way, the correct behavior is now
to reset the link instead of trying to revert its sequence number.
So, this is what we do in this commit.
Signed-off-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the first fragment of a long data data message is received on a link, a
reassembly buffer large enough to hold the data from this and all subsequent
fragments of the message is allocated. The payload of each new fragment is
copied into this buffer upon arrival. When the last fragment is received, the
reassembled message is delivered upwards to the port/socket layer.

Not only is this an inefficient approach, but it may also cause bursts of
reassembly failures in low memory situations. since we may fail to allocate
the necessary large buffer in the first place. Furthermore, after 100 subsequent
such failures the link will be reset, something that in reality aggravates the
situation.

To remedy this problem, this patch introduces a different approach. Instead of
allocating a big reassembly buffer, we now append the arriving fragments
to a reassembly chain on the link, and deliver the whole chain up to the
socket layer once the last fragment has been received. This is safe because
the retransmission layer of a TIPC link always delivers packets in strict
uninterrupted order, to the reassembly layer as to all other upper layers.
Hence there can never be more than one fragment chain pending reassembly at
any given time in a link, and we can trust (but still verify) that the
fragments will be chained up in the correct order.
Signed-off-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a message fragment is received in a broadcast or unicast link,
the reception code will append the fragment payload to a big reassembly
buffer through a call to the function tipc_recv_fragm(). However, after
the return of that call, the logics goes on and passes the fragment
buffer to the function tipc_net_route_msg(), which will simply drop it.
This behavior is a remnant from the now obsolete multi-cluster
functionality, and has no relevance in the current code base.

Although currently harmless, this unnecessary call would be fatal
after applying the next patch in this series, which introduces
a completely new reassembly algorithm. So we change the code to
eliminate the redundant call.
Signed-off-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now rt6_alloc_cow() is only called by ip6_pol_route() when
rt->rt6i_flags doesn't contain both RTF_NONEXTHOP and RTF_GATEWAY,
and rt->rt6i_flags hasn't been changed in ip6_rt_copy().
So there is no neccessary to judge whether rt->rt6i_flags contains
RTF_GATEWAY or not.
Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 1e2bd517 ("udp6: Fix udp
fragmentation for tunnel traffic.") changed the calculation if
there is enough space to include a fragment header in the skb from a
skb->mac_header dervived one to skb_headroom. Because we already peeled
off the skb to transport_header this is wrong. Change this back to check
if we have enough room before the mac_header.

This fixes a panic Saran Neti reported. He used the tbf scheduler which
skb_gso_segments the skb. The offsets get negative and we panic in memcpy
because the skb was erroneously not expanded at the head.
Reported-by: NSaran Neti <Saran.Neti@telus.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sockets marked with IP_PMTUDISC_INTERFACE won't do path mtu discovery,
their sockets won't accept and install new path mtu information and they
will always use the interface mtu for outgoing packets. It is guaranteed
that the packet is not fragmented locally. But we won't set the DF-Flag
on the outgoing frames.

Florian Weimer had the idea to use this flag to ensure DNS servers are
never generating outgoing fragments. They may well be fragmented on the
path, but the server never stores or usees path mtu values, which could
well be forged in an attack.

(The root of the problem with path MTU discovery is that there is
no reliable way to authenticate ICMP Fragmentation Needed But DF Set
messages because they are sent from intermediate routers with their
source addresses, and the IMCP payload will not always contain sufficient
information to identify a flow.)

Recent research in the DNS community showed that it is possible to
implement an attack where DNS cache poisoning is feasible by spoofing
fragments. This work was done by Amir Herzberg and Haya Shulman:
<https://sites.google.com/site/hayashulman/files/fragmentation-poisoning.pdf>

This issue was previously discussed among the DNS community, e.g.
<http://www.ietf.org/mail-archive/web/dnsext/current/msg01204.html>,
without leading to fixes.

This patch depends on the patch "ipv4: fix DO and PROBE pmtu mode
regarding local fragmentation with UFO/CORK" for the enforcement of the
non-fragmentable checks. If other users than ip_append_page/data should
use this semantic too, we have to add a new flag to IPCB(skb)->flags to
suppress local fragmentation and check for this in ip_finish_output.

Many thanks to Florian Weimer for the idea and feedback while implementing
this patch.

Cc: David S. Miller <davem@davemloft.net>
Suggested-by: NFlorian Weimer <fweimer@redhat.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code of flow label in Linux Kernel follows
the rules of RFC 1809 (an informational one) for
conditions on flow label sharing. There rules are
not in the last proposed standard for flow label
(RFC 6437), or in the previous one (RFC 3697).

Since this code does not follow any current or
old standard, we can remove it.

With this removal, the ipv6_opt_cmp function is
now a dead code and it can be removed too.

Changelog to v1:
 * add justification for the change
 * remove the condition on IPv6 options

[ Remove ipv6_hdr_cmp and it is now unused as well. -DaveM ]
Signed-off-by: NFlorent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sometimes we need to coalesce the rx frags to avoid frag list. One example is
virtio-net driver which tries to use small frags for both MTU sized packet and
GSO packet. So this patch introduce skb_coalesce_rx_frag() to do this.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Michael Dalton <mwdalton@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Slow start now increases cwnd by 1 if an ACK acknowledges some packets,
regardless the number of packets. Consequently slow start performance
is highly dependent on the degree of the stretch ACKs caused by
receiver or network ACK compression mechanisms (e.g., delayed-ACK,
GRO, etc).  But slow start algorithm is to send twice the amount of
packets of packets left so it should process a stretch ACK of degree
N as if N ACKs of degree 1, then exits when cwnd exceeds ssthresh. A
follow up patch will use the remainder of the N (if greater than 1)
to adjust cwnd in the congestion avoidance phase.

In addition this patch retires the experimental limited slow start
(LSS) feature. LSS has multiple drawbacks but questionable benefit. The
fractional cwnd increase in LSS requires a loop in slow start even
though it's rarely used. Configuring such an increase step via a global
sysctl on different BDPS seems hard. Finally and most importantly the
slow start overshoot concern is now better covered by the Hybrid slow
start (hystart) enabled by default.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Applications have started to use Fast Open (e.g., Chrome browser has
such an optional flag) and the feature has gone through several
generations of kernels since 3.7 with many real network tests. It's
time to enable this flag by default for applications to test more
conveniently and extensively.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to use the _safe version of list_for_each_entry() here otherwise
we have a use after free bug.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

This patch fixes a build warning in skb_checksum() by wrapping the
csum_partial() usage in skb_checksum(). The problem is that on a few
architectures, csum_partial is used with prefix asmlinkage whereas
on most architectures it's not. So fix this up generically as we did
with csum_block_add_ext() to match the signature. Introduced by
2817a336 ("net: skb_checksum: allow custom update/combine for
walking skb").
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduced in f9e42b85 ("net: sctp: sideeffect: throw BUG if
primary_path is NULL"), we intended to find a buggy assoc that's
part of the assoc hash table with a primary_path that is NULL.
However, we better remove the BUG_ON for now and find a more
suitable place to assert for these things as Mark reports that
this also triggers the bug when duplication cookie processing
happens, and the assoc is not part of the hash table (so all
good in this case). Such a situation can for example easily be
reproduced by:

  tc qdisc add dev eth0 root handle 1: prio bands 2 priomap 1 1 1 1 1 1
  tc qdisc add dev eth0 parent 1:2 handle 20: netem loss 20%
  tc filter add dev eth0 protocol ip parent 1: prio 2 u32 match ip \
            protocol 132 0xff match u8 0x0b 0xff at 32 flowid 1:2

This drops 20% of COOKIE-ACK packets. After some follow-up
discussion with Vlad we came to the conclusion that for now we
should still better remove this BUG_ON() assertion, and come up
with two follow-ups later on, that is, i) find a more suitable
place for this assertion, and possibly ii) have a special
allocator/initializer for such kind of temporary assocs.
Reported-by: NMark Thomas <Mark.Thomas@metaswitch.com>
Signed-off-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

High-availability Seamless Redundancy ("HSR") provides instant failover
redundancy for Ethernet networks. It requires a special network topology where
all nodes are connected in a ring (each node having two physical network
interfaces). It is suited for applications that demand high availability and
very short reaction time.

HSR acts on the Ethernet layer, using a registered Ethernet protocol type to
send special HSR frames in both directions over the ring. The driver creates
virtual network interfaces that can be used just like any ordinary Linux
network interface, for IP/TCP/UDP traffic etc. All nodes in the network ring
must be HSR capable.

This code is a "best effort" to comply with the HSR standard as described in
IEC 62439-3:2010 (HSRv0).
Signed-off-by: NArvid Brodin <arvid.brodin@xdin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Joby Poriyath provided a xen-netback patch to reduce the size of
xenvif structure as some netdev allocation could fail under
memory pressure/fragmentation.

This patch is handling the problem at the core level, allowing
any netdev structures to use vmalloc() if kmalloc() failed.

As vmalloc() adds overhead on a critical network path, add __GFP_REPEAT
to kzalloc() flags to do this fallback only when really needed.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NJoby Poriyath <joby.poriyath@citrix.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes an outstanding bug found through IPVS, where SCTP packets
with skb->data_len > 0 (non-linearized) and empty frag_list, but data
accumulated in frags[] member, are forwarded with incorrect checksum
letting SCTP initial handshake fail on some systems. Linearizing each
SCTP skb in IPVS to prevent that would not be a good solution as
this leads to an additional and unnecessary performance penalty on
the load-balancer itself for no good reason (as we actually only want
to update the checksum, and can do that in a different/better way
presented here).

The actual problem is elsewhere, namely, that SCTP's checksumming
in sctp_compute_cksum() does not take frags[] into account like
skb_checksum() does. So while we are fixing this up, we better reuse
the existing code that we have anyway in __skb_checksum() and use it
for walking through the data doing checksumming. This will not only
fix this issue, but also consolidates some SCTP code with core
sk_buff code, bringing it closer together and removing respectively
avoiding reimplementation of skb_checksum() for no good reason.

As crc32c() can use hardware implementation within the crypto layer,
we leave that intact (it wraps around / falls back to e.g. slice-by-8
algorithm in __crc32c_le() otherwise); plus use the __crc32c_le_combine()
combinator for crc32c blocks.

Also, we remove all other SCTP checksumming code, so that we only
have to use sctp_compute_cksum() from now on; for doing that, we need
to transform SCTP checkumming in output path slightly, and can leave
the rest intact.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, skb_checksum walks over 1) linearized, 2) frags[], and
3) frag_list data and calculats the one's complement, a 32 bit
result suitable for feeding into itself or csum_tcpudp_magic(),
but unsuitable for SCTP as we're calculating CRC32c there.

Hence, in order to not re-implement the very same function in
SCTP (and maybe other protocols) over and over again, use an
update() + combine() callback internally to allow for walking
over the skb with different algorithms.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove duplicated include.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

With the intent to dump other accounting data later.
This patch is a cleanup.
Signed-off-by: NHolger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Encapsulate counters for both directions into nf_conn_acct. During
that process also consistently name pointers to the extend 'acct',
not 'counters'. This patch is a cleanup.
Signed-off-by: NHolger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

We don't validate iph->ihl which may lead a dead loop if we meet a IPIP
skb whose iph->ihl is zero. Fix this by failing immediately when iph->ihl
is evil (less than 5).

This issue were introduced by commit ec5efe79
(rps: support IPIP encapsulation).

Cc: Eric Dumazet <edumazet@google.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow->hash can be used to detect hash collisions and avoid flow key
compare in flow lookup.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

    tcp_flags=flags/mask
        Bitwise  match on TCP flags.  The flags and mask are 16-bit num‐
        bers written in decimal or in hexadecimal prefixed by 0x.   Each
        1-bit  in  mask requires that the corresponding bit in port must
        match.  Each 0-bit in mask causes the corresponding  bit  to  be
        ignored.

        TCP  protocol  currently  defines  9 flag bits, and additional 3
        bits are reserved (must be transmitted as zero), see  RFCs  793,
        3168, and 3540.  The flag bits are, numbering from the least
        significant bit:

        0: FIN No more data from sender.

        1: SYN Synchronize sequence numbers.

        2: RST Reset the connection.

        3: PSH Push function.

        4: ACK Acknowledgement field significant.

        5: URG Urgent pointer field significant.

        6: ECE ECN Echo.

        7: CWR Congestion Windows Reduced.

        8: NS  Nonce Sum.

        9-11:  Reserved.

        12-15: Not matchable, must be zero.
Signed-off-by: NJarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

Widen TCP flags handling from 7 bits (uint8_t) to 12 bits (uint16_t).
The kernel interface remains at 8 bits, which makes no functional
difference now, as none of the higher bits is currently of interest
to the userspace.
Signed-off-by: NJarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

OVS already can handle all types of segmentation offloads that
are supported by the kernel.
Following patch specifically enables UDP and IPV6 segmentation
offloads.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

On some codepaths the skb does not have a dst entry
when xfrm_decode_session() is called. So check for
a valid skb_dst() before dereferencing the device
interface index. We use 0 as the device index if
there is no valid skb_dst(), or at reverse decoding
we use skb_iif as device interface index.

Bug was introduced with git commit bafd4bd4
("xfrm: Decode sessions with output interface.").
Reported-by: NMeelis Roos <mroos@linux.ee>
Tested-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>

This patch drops the direct memcpy on skb and uses the right skb
memcpy functions. Also remove an unnecessary check if plen is non zero.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Reviewed-by: NWerner Almesberger <werner@almesberger.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is necessary to access network header with the skb_network_header
function instead of calculate the position with mac_len, etc.
Do the same for the transport header, when we replace the IPv6 header
with the 6LoWPAN header.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Acked-by: NWerner Almesberger <werner@almesberger.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>