Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The caller will free acquired resouces if a failure occurs.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were turning on the carrier without verifying the link was up.
This adds link up to the link initialize check before turning carrier
on.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not clearing the routing bits can cause frames to erroneously get routed to
management processor.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware semaphore covers the configuration register as well as the
ICB registers.  The ICB high and low regs contain the address of the
initialization control block and the config register is used to signal
the hardware that a block is ready to be downloaded.  Currently we were
only protecting the ICB regs.  This changes expands to cover the config
register as well.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a bug in addrconf_prefix_rcv() where it won't update the
preferred lifetime of an IPv6 address if the current valid lifetime
of the address is less than 2 hours (the minimum value in the RA).

For example, If I send a router advertisement with a prefix that
has valid lifetime = preferred lifetime = 2 hours we'll build
this address:

3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
    inet6 2001:1890:1109:a20:217:8ff:fe7d:4718/64 scope global dynamic
       valid_lft 7175sec preferred_lft 7175sec

If I then send the same prefix with valid lifetime = preferred
lifetime = 0 it will be ignored since the minimum valid lifetime
is 2 hours:

3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
    inet6 2001:1890:1109:a20:217:8ff:fe7d:4718/64 scope global dynamic
       valid_lft 7161sec preferred_lft 7161sec

But according to RFC 4862 we should always reset the preferred lifetime
even if the valid lifetime is invalid, which would cause the address
to immediately get deprecated.  So with this patch we'd see this:

5: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
    inet6 2001:1890:1109:a20:21f:29ff:fe5a:ef04/64 scope global deprecated dynamic
       valid_lft 7163sec preferred_lft 0sec

The comment winds-up being 5x the size of the code to fix the problem.

Update the preferred lifetime of IPv6 addresses derived from a prefix
info option in a router advertisement even if the valid lifetime in
the option is invalid, as specified in RFC 4862 Section 5.5.3e.  Fixes
an issue where an address will not immediately become deprecated.
Reported by Jens Rosenboom.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SCTP pushed the skb above the sctp chunk header, so the
check of pskb_may_pull(skb, nh + offset + 1 - skb->data) in
_decode_session6() will never return 0 and the ports decode
of sctp will always fail. (nh + offset + 1 - skb->data < 0)
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SCTP pushed the skb data above the sctp chunk header, so the check
of pskb_may_pull(skb, xprth + 4 - skb->data) in _decode_session4() will
never return 0 because xprth + 4 - skb->data < 0, the ports decode of
sctp will always fail.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is not safe to use match_int without checking the token type returned
by match_token (especially when the token type returned is Opt_err and
args is empty). Fix it.
Signed-off-by: NAbhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds ETH_P_1588 protocol ID define.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PHY_HALTED state disables phydev->link, but the link will not be
updated upon entering PHY_RESUMING.  Add a call to phy_read_status() to
update the link before entering PHY_RUNNING.  If the link is not up at
this point, enter the PHY_NOLINK state instead.

Also, when transitioning from PHY_RESUMING to PHY_RUNNING, calls to
netif_carrier_on() and phydev->adjust_link() are missing.  Add the calls
similar to the other transitions to PHY_RUNNING.
Signed-off-by: NWade Farnsworth <wfarnsworth@mvista.com>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Restrict firmware reset to following cases -

o chip rev is NX2031 (firmare doesn't support heartbit).
o firmware is dead.
o previous attempt to init firmware had failed.
o we have got newer file firmware.

This speeds up module load tremendously (by upto 8 sec),
also avoids downtime for NCSI (management) pass-thru
traffic.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct firmware encoding is 8 bit major, 8 bit minor and
16 bit subversion. Flash has sizes rightly set, but original
driver submission messed it leaving 16 bit major and 8 bit
subversion.

Also fix a infinite loop when cut-thru file firmware is
invalid.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drop a sanity check which doesn't serve any useful purpose anymore.
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ISDN connection setup failed if the "connection active" and
"B channel up" messages from the device arrived in a different
order than expected. Modify the state machine to accept them in
any order.

Impact: bugfix
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
CC: stable <stable@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 73ce7b01.

After discovering that we don't listen to gratuitious arps in 2.6.30
I tracked the failure down to this commit.

The patch makes absolutely no sense.  RFC2131 RFC3927 and RFC5227.
are all in agreement that an arp request with sip == 0 should be used
for the probe (to prevent learning) and an arp request with sip == tip
should be used for the gratitous announcement that people can learn
from.

It appears the author of the broken patch got those two cases confused
and modified the code to drop all gratuitous arp traffic.  Ouch!

Cc: stable@kernel.org
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PCI drivers that implement the io_error_detected callback should return
PCI_ERS_RESULT_DISCONNECT if the state passed in is
pci_channel_io_perm_failure.  This patch fixes the issue for igb.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

on permanent failure

PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure.  This state is not
checked in many of the network drivers.

This patch fixes the omission in the e1000e driver.
Signed-off-by: NMike Mason <mmlnx@us.ibm.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure.  This state is
not checked in many of the network drivers.

The patch fixes the omission in the e1000 driver.

Based on Mike Mason's similar patch for e1000e.
Signed-off-by: NAndre Detsch <adetsch@br.ibm.com>
CC: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

as reported by kerneloops.org

[  121.781161] ------------[ cut here ]------------
[  121.781171] WARNING: at lib/dma-debug.c:793 check_unmap+0x14e/0x577()
[  121.781173] Hardware name: S5520HC
[  121.781177] e1000 0000:0a:00.0: DMA-API: device driver tries to free DMA
memory it has not allocated [device address=0x00000001d688b0fa] [size=1522
bytes]
[  121.781180] Modules linked in: e1000 mdio  dca [last unloaded: ixgbe]
[  121.781187] Pid: 4793, comm: bash Tainted: P 2.6.30-master-06161113 #3
[  121.781190] Call Trace:
[  121.781195]  [<ffffffff8123056f>] ? check_unmap+0x14e/0x577
[  121.781201]  [<ffffffff81057a19>] warn_slowpath_common+0x77/0x8f
[  121.781205]  [<ffffffff81057ae1>] warn_slowpath_fmt+0x9f/0xa1
[  121.781212]  [<ffffffff81477ce2>] ? _spin_lock_irqsave+0x3f/0x49
[  121.781216]  [<ffffffff8122fa97>] ? get_hash_bucket+0x28/0x33
[  121.781220]  [<ffffffff8123056f>] check_unmap+0x14e/0x577
[  121.781225]  [<ffffffff810e4f48>] ? check_bytes_and_report+0x38/0xcb
[  121.781230]  [<ffffffff81230bbf>] debug_dma_unmap_page+0x80/0x92
[  121.781234]  [<ffffffff8122e549>] ? unmap_single+0x1a/0x4e
[  121.781239]  [<ffffffff813901e1>] ? __kfree_skb+0x74/0x78
[  121.781250]  [<ffffffffa00662ef>] pci_unmap_single+0x64/0x6d [e1000]
[  121.781259]  [<ffffffffa0066344>] e1000_clean_rx_ring+0x4c/0xbf [e1000]
[  121.781268]  [<ffffffffa00663df>] e1000_clean_all_rx_rings+0x28/0x36 [e1000]
[  121.781277]  [<ffffffffa0067464>] e1000_down+0x138/0x141 [e1000]
[  121.781286]  [<ffffffffa00681c2>] __e1000_shutdown+0x6b/0x198 [e1000]
[  121.781296]  [<ffffffffa0068405>] e1000_suspend+0x17/0x50 [e1000]
[  121.781301]  [<ffffffff81237665>] pci_legacy_suspend+0x3b/0xbe
[  121.781305]  [<ffffffff81237bc6>] pci_pm_suspend+0x3e/0xf1
[  121.781310]  [<ffffffff812eaf1c>] pm_op+0x57/0xde
[  121.781314]  [<ffffffff812eb444>] dpm_suspend_start+0x31e/0x470
[  121.781319]  [<ffffffff810877da>] suspend_devices_and_enter+0x3e/0x1a2
[  121.781323]  [<ffffffff81087a0f>] enter_state+0xd1/0x127
[  121.781327]  [<ffffffff8108717a>] state_store+0xa7/0xc9
[  121.781332]  [<ffffffff81221843>] kobj_attr_store+0x17/0x19
[  121.781336]  [<ffffffff8113c01e>] sysfs_write_file+0xe5/0x121
[  121.781341]  [<ffffffff810ed165>] vfs_write+0xab/0x105
[  121.781344]  [<ffffffff810ed279>] sys_write+0x47/0x6d
[  121.781349]  [<ffffffff81027aab>] system_call_fastpath+0x16/0x1b
[  121.781352] ---[ end trace 97bacaaac2ed7786 ]---

Fix is to correctly zero out internal ->dma value when unmapping
and make sure never to unmap unless there specifically was a mapping done.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

driver was mixing NET_IP_ALIGN count bytes in map/unmap calls
unevenly. Only map the bytes that the hardware might dma into

also fix unmap related bug where ->dma was not being cleared
after unmap
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses three WARN_ON statements from DMA-API debug code

ixgbe is mapping more than it unmaps, reduce the length of the map call and
remove the "used once" local variable.

found by Joerg Roedel <joerg.roedel@amd.com> in 2.6.30, so is a candidate
for -stable.

in addition, fix missing ->dma = 0 after unmap to prevent double free with
pci_unmap_single

and lastly, don't unmap (half) pages that aren't mapped.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adapter link advertisement capabilities were not persistent during
adapter resets. While configuring multispeed fiber link check for
phy autoneg_advertised settings before overwriting with default
link capabilities
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

82599 single speed fiber modules only support 10G/Full. Return
proper device capabilities while querrying the adapter and error
while changing device advertisement/speed/duplex capabilities.
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We had a wide range of log messages for the same sort of SFP
failure.  This patch makes them all more similar and less
confusing along with converting them to dev_err.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that nothing uses the private stats structure we can remove it.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that netdev has its own stats structure we should use that
instead.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alas current delaying of freeing old tnodes by RCU in trie_rebalance
is still not enough because we can free a top tnode before updating a
t->trie pointer.
Reported-by: NPawel Staszewski <pstaszewski@itcare.pl>
Tested-by: NPawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the same fix as commit
7959ea25 ("bnx2: Fix the behavior of
ethtool when ONBOOT=no"), but for bnx2x:

--------------------
    When configure in ifcfg-eth* is ONBOOT=no,
    the behavior of ethtool command is wrong.
    
        # grep ONBOOT /etc/sysconfig/network-scripts/ifcfg-eth2
        ONBOOT=no
        # ethtool eth2 | tail -n1
                Link detected: yes
    
    I think "Link detected" should be "no".
--------------------
Signed-off-by: NNaohiro Ooiwa <nooiwa@miraclelinux.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 'net: skb->dst accessors'(adf30907)
broken the sctp protocol stack, the sctp packet can never be sent out after
Eric Dumazet's patch, which have typo in the sctp code.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NVlad Yasevich <vladisalv.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clean up to use xfrm_addr_cmp() instead of compare addresses directly.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a socket starts out on a non-TSO route, and then switches to
a TSO route, then we will tack on data to the tail of the tx queue
even if it started out life as non-TSO.  This is suboptimal because
all of it will then be copied and checksummed unnecessarily.

This patch fixes this by ensuring that skb->ip_summed is set to
CHECKSUM_PARTIAL before appending extra data beyond the MSS.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a socket starts out on a non-TSO route, and then switches to
a TSO route, then the tail on the tx queue can morph into a TSO
packet, causing mischief because the rest of the stack does not
expect a partially linear TSO packet.

This patch fixes this by ensuring that skb->ip_summed is set to
CHECKSUM_PARTIAL before declaring a packet as TSO.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>