On OMAP4 SOC, intecronnects has many write buffers in the async bridges
and they need to be drained before CPU enters into standby state.

Patch 'OMAP4: PM: Add CPUX OFF mode support' added CPU PM support
but OMAP errata i688 (Async Bridge Corruption) needs to be taken
care to avoid issues like system freeze, CPU deadlocks, random
crashes with register accesses, synchronisation loss on initiators
operating on both interconnect port simultaneously.

As per the errata, if a data is stalled inside asynchronous bridge
because of back pressure, it may be accepted multiple times, creating
pointer misalignment that will corrupt next transfers on that data
path until next reset of the system (No recovery procedure once
the issue is hit, the path remains consistently broken).
Async bridge can be found on path between MPU to EMIF and
MPU to L3 interconnect. This situation can happen only when the
idle is initiated by a Master Request Disconnection (which is
trigged by software when executing WFI on CPU).

The work-around for this errata needs all the initiators
connected through async bridge must ensure that data path
is properly drained before issuing WFI. This condition will be
met if one Strongly ordered access is performed to the
target right before executing the WFI. In MPU case, L3 T2ASYNC
FIFO and DDR T2ASYNC FIFO needs to be drained. IO barrier ensure
that there is no synchronisation loss on initiators operating
on both interconnect port simultaneously.

Thanks to Russell for a tip to conver assembly function to
C fuction there by reducing 40 odd lines of code from the patch.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NRichard Woodruff <r-woodruff2@ti.com>
Acked-by: NJean Pihet <j-pihet@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NVishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

kbuild explicitly includes this at build time.
Signed-off-by: NDave Jones <davej@redhat.com>

Base patch for PA6T and PA6T-1682M. This introduces the
arch/powerpc/platform/pasemi directory, together with basic
implementations for various setup.

Much of this was based on other platform code, i.e. Maple, etc.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This is a patch for the Hilscher netx builtin ethernet ports. The
netx board support was merged into 2.6.17-git2.
The netx is a arm926 based SoC.
Signed-off-by: NRobert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

--
 drivers/net/Kconfig             |   11
 drivers/net/Makefile            |    1
 drivers/net/netx-eth.c          |  516 ++++++++++++++++++++++++++++++++++++++++
 include/asm-arm/arch-netx/eth.h |   27 ++
 4 files changed, 555 insertions(+)
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Patch from Sascha Hauer

This patch adds the base support for Hilscher's netX network
processors.
Signed-off-by: NRobert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Sascha Hauer

This patch adds framebuffer support for Hilscher's netX network
processors.
Signed-off-by: NRobert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from SAN People

Following changes were made to clock.c:

1) Replaced <asm/hardware/clock.h> with <linux/clk.h>
2) Removed old unused clk_enable & clk_disable.
3) Replaced clk_use/clk_unuse with clk_enable/clk_disable.

Otherwise it's the same as the previous patch.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Including asm/hardware.h into asm/io.h can cause #define clashes
between platform specific definitions and driver local definitions.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!