提交 · 132e23775779cc895c37f7883c33a60a1a8a7cdd · openeuler / raspberrypi-kernel

29 7月, 2015 34 次提交

usb: musb: sunxi: Add support for musb controller in A31 SoC · 132e2377

由 Hans de Goede 提交于 7月 08, 2015

The A31 SoC uses the same musb controller as found in earlier SoCs, but it
is hooked up slightly different. Its SRAM is private and no longer controlled
through the SRAM controller, and its reset is controlled via a separate
reset controller. This commit adds support for this setup.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

132e2377

usb: musb: sunxi: Add support for the Allwinner sunxi musb controller · 744543c5

由 Hans de Goede 提交于 7月 08, 2015

This is based on initial code to get the Allwinner sunxi musb controller
supported by Chen-Yu Tsai and Roman Byshko.

This adds support for the Allwinner sunxi musb controller in both host only
and otg mode. Peripheral only mode is not supported, as no boards use that.

This has been tested on a cubietruck (A20 SoC) and an UTOO P66 tablet
(A13 SoC) with a variety of devices in host mode and with the g_serial gadget
driver in peripheral mode, plugging otg / host cables in/out a lot of times
in all possible imaginable plug orders.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

744543c5

usb: gadget: f_obex: use bind_deactivated flag · 4cfbd952

由 Robert Baldyga 提交于 5月 04, 2015

Use bind_deactivated flag instead of calling usb_function_deactivate()
in function bind(). Field 'can_activate' in struct f_obex is no longer
needed as setting 'bind_deactivated' flag makes us sure, that the function
will be binded only if deactivation can be performed successfully.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

4cfbd952

usb: gadget: f_uvc: use bind_deactivated flag · f277bf27

由 Robert Baldyga 提交于 5月 04, 2015

Use bind_deactivated flag instead of calling usb_function_deactivate()
in function bind().
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

f277bf27

usb: composite: add bind_deactivated flag to usb_function · d5bb9b81

由 Robert Baldyga 提交于 5月 04, 2015

This patch introduces 'bind_deactivated' flag in struct usb_function.
Functions which don't want to be activated automatically after bind should
set this flag, and when they start to be ready to work they should call
usb_function_activate().

When USB function sets 'bind_deactivated' flag, initial deactivation
counter is incremented automatically, so there is no need to call
usb_function_deactivate() in function bind.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

d5bb9b81

usb: composite: fix usb_function_activate/deactivate functions · 5601250b

由 Robert Baldyga 提交于 5月 04, 2015

Using usb_gadget_disconnect to make gadget temporarily invisible to host
doesn't provide desired result, because gadget is connected immediately
after binding regardless to previous usb_gadget_disconnect() calls.

For this reason we use usb_gadget_deactivate() instead of
usb_gadget_disconnect() to make it working as expected.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

5601250b

usb: gadget: add usb_gadget_activate/deactivate functions · ccdf138f

由 Robert Baldyga 提交于 5月 04, 2015

These functions allows to deactivate gadget to make it not visible to
host and make it active again when gadget driver is finally ready.

They are needed to fix usb_function_activate() and usb_function_deactivate()
functions which currently are not working as usb_gadget_connect() is
called immediately after function bind regardless to previous calls of
usb_gadget_disconnect() function.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

ccdf138f

usb: phy: qcom: New APQ8016/MSM8916 USB transceiver driver · 35116993

由 Ivan T. Ivanov 提交于 7月 08, 2015

Driver handles PHY initialization, clock management, power
management and workarounds required after resetting the hardware.
Signed-off-by: NIvan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

35116993

usb: gadget: storage-common: Set FSG_MAX_LUNS to 16 · 75ddead2

由 Krzysztof Opasiak 提交于 7月 20, 2015

Mass storage spec allows up to 16 LUNs, so let's not
add some more restrictive limits.
Signed-off-by: NKrzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

75ddead2

usb: gadget: mass_storage: Place EXPORT_SYMBOL_GPL() after func definition · bab7a1f1

由 Krzysztof Opasiak 提交于 7月 20, 2015

EXPORT_SYMBOL_GPL() is usually placed after function definition
not before.
Signed-off-by: NKrzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

bab7a1f1

usb: gadget: mass_storage: Free buffers if create lun fails · 903588a9

由 Krzysztof Opasiak 提交于 7月 20, 2015

Creation of LUN 0 may fail (for example due to ENOMEM).
As fsg_common_set_num_buffers() does some memory allocation
we should free it before it becomes unavailable.
Signed-off-by: NKrzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

903588a9

usb: dwc3: gadget: defer endpoint name change · aa739974

由 Felipe Balbi 提交于 7月 20, 2015

We should only change endpoint names when we
actually manage to enable/disable it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

aa739974

usb: dwc3: gadget: add a trace when disabling EPs · 7eaeac5c

由 Felipe Balbi 提交于 7月 20, 2015

We have a "Enabling %s" trace when enabling an endpoint
but that message felt lonely without a matching
"Disabling %s". Add it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

7eaeac5c

usb: dwc3: core: remove unnecessary dev_warn() · d9972f47

由 Felipe Balbi 提交于 7月 07, 2015

When a SoC supports both PHY interfaces but
doesn't define HSPHY in DT/pdata, we will get
an unnecessary dev_warn() which can mislead users
into thinking that they're missing something.

Instead, let's just silently rely on a correct
default. If the HW default is wrong, then HSPHY
is required and USB won't work, this will be
motivation enough for engineers to patch their
way into a working setup.
Reported-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

d9972f47

usb: pass flags parameter to gpiod_get functions · 88167fc0

由 Uwe Kleine-König 提交于 7月 06, 2015

Since 39b2bbe3 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.

Currently this parameter is made optional with the help of a cpp trick.
To allow dropping this hack convert callers to explictly pass a value
for flags.
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

88167fc0

usb: dwc3: pci: make better use of gpiod API · 2df033ca

由 Uwe Kleine-König 提交于 7月 06, 2015

Since 39b2bbe3 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.

Use this additional parameter and the _optional variant to simplify the
driver and improve error handling. Also expand the comment to explain
why it's not sensible to switch to devm_gpiod_get and why the gpiod_put
is also necessary.

Furthermore this is one caller less that stops us making the flags
argument to gpiod_get*() mandatory.
Tested-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

2df033ca

usb: phy: msm-usb: Replace deprecated API of extcon · 83b7b67c

由 Chanwoo Choi 提交于 7月 01, 2015

This patch removes the deprecated notifier API of extcon framwork
and then use the new extcon API with the unique id to indicate
the each external connector (USB, USB-HOST).

Alter deprecated API as following:
- extcon_register_interest() -> extcon_register_notifier()
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)

Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

83b7b67c

usb: renesas_usbhs: Replace deprecated API of extcon · 50297b79

由 Chanwoo Choi 提交于 7月 01, 2015

This patch removes the deprecated API of extcon and then use the new extcon API
with the unique id to indicate the each external connector (USB-HOST).
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Varka Bhadram <varkab@cdac.in>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

50297b79

usb: phy: tahvo: Use devm_extcon_dev_[allocate|register]() and replace deprecated API · 860d2686

由 Chanwoo Choi 提交于 7月 01, 2015

This patch uses the devm_extcon_dev_[allocate|register]() to manage the
resource automatically and replace deprecated API as following:
- extcon_[set|get]_cable_state(*edev, char *) -> extcon_[set|get]_cable_state_(*edev, id)

Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

860d2686

usb: phy: omap-otg: Replace deprecated API of extcon · a2fd2423

由 Chanwoo Choi 提交于 7月 01, 2015

This patch removes the deprecated notifier API of extcon framwork
and then use the new extcon API with the unique id to indicate
the each external connector (USB, USB-HOST).

Alter deprecated API as following:
- extcon_register_interest() -> extcon_register_notifier()
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)

[ balbi@ti.com : fix build break ]

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

a2fd2423

usb: dwc3: omap: Replace deprecated API of extcon · 5960387a

由 Chanwoo Choi 提交于 7月 01, 2015

This patch removes the deprecated notifier API of extcon framwork
and then use the new extcon API with the unique id to indicate
the each external connector (USB, USB-HOST).

Alter deprecated API as following:
- extcon_register_interest() -> extcon_register_notifier()
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)

Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

5960387a

usb: udc: Convert use of __constant_cpu_to_leXX to cpu_to_leXX · b5c03bff

由 Vaishali Thakkar 提交于 6月 10, 2015

In big endian cases, the macro cpu_to_le{16,32} unfolds to __swab{16,32}
which provides special case for constants. In little endian cases,
__constant_cpu_to_le{16,32} and cpu_to_le{16,32} expand directly to
the same expression. So, replace __constant_cpu_to_le{16,32} with
cpu_to_le{16,32} with the goal of getting rid of the definition of
__constant_cpu_to_le{16,32} completely.

The semantic patch that performs this transformation is as follows:

@@expression x;@@

(
- __constant_cpu_to_le16(x)
+ cpu_to_le16(x)
|
- __constant_cpu_to_le32(x)
+ cpu_to_le32(x)
)
Signed-off-by: NVaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

b5c03bff

usb: gadget: composite.c: i18n is not an acronym · ad4676ab

由 Diego Viola 提交于 5月 31, 2015

I18N should be spelled as i18n because it's not
an acronym
Signed-off-by: NDiego Viola <diego.viola@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

ad4676ab

usb: gadget: Convert use of __constant_cpu_to_le16 to cpu_to_le16 · b8464bcf

由 Vaishali Thakkar 提交于 6月 06, 2015

In big endian cases, macro cpu_to_le16 unfolds to __swab16 which
provides special case for constants. In little endian cases,
__constant_cpu_to_le16 and cpu_to_le16 expand directly to the
same expression. So, replace __constant_cpu_to_le16 with
cpu_to_le16 with the goal of getting rid of the definition of
__constant_cpu_to_le16 completely.

The semantic patch that performs this transformation is as follows:

@@expression x;@@

- __constant_cpu_to_le16(x)
+ cpu_to_le16(x)
Signed-off-by: NVaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

b8464bcf

usb: gadget: SourceSink: Remove out-of-date comment · d3c1ac4a

由 Krzysztof Opasiak 提交于 6月 19, 2015

As SourceSink function has been reworked for ConfigFS
composite gadget this comment is no longer valid.
Signed-off-by: NKrzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

d3c1ac4a

usb: gadget: loopback: Remove out-of-date comment · e425be93

由 Krzysztof Opasiak 提交于 6月 19, 2015

As loopback function has been reworked for ConfigFS
composite gadget this comment is no longer valid.
Signed-off-by: NKrzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

e425be93

usb: dwc3: drop CONFIG_USB_DWC3_DEBUG · 9fcfa463