... and rewrite the initialization of output paths as a generic
function that is applicable for both i/o directions.

The new flag, active, is introduced to each nid_path entry.  This
indicates whether the given path is active, and it's used for checking
whether a certain widget can be turned off or changed when a path is
no longer used or newly enabled.

It's still used only in the output paths.  More wider adaption for
input and loopback paths will be achieved in the later patch.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

We are using only AUTOMUTE_MODE_PIN in patch_realtek.c and all others
have been already dropped.  Let's remove the old superfluous codes.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The new function snd_hda_codec_amp_init() (and the stereo variant)
initializes the amp value only once at the first access.  If the amp
was already initialized or updated, this won't do anything more.

It's useful for initializing the input amps that are in the part of
the path but never used.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For optimizing the verb executions, a new mechanism to cache the verbs
and amp update commands is introduced.  With the new "write to cache
and flush" way, you can reduce the same verbs that have been written
multiple times.

When codec->cached_write flag is set, the further
snd_hda_codec_write_cache() and snd_hda_codec_amp_stereo() calls will
be performed only on the command or amp cache table, but not sent to
the hardware yet.  Once after you call all commands and update amps,
call snd_hda_codec_resume_amp() and snd_hda_codec_resume_cache().
Then all cached writes and amp updates will be written to the
hardware, and the dirty flags are cleared.

In this implementation, the existing cache table is reused, so
actually no big code change is seen here.  Each cache entry has a new
dirty flag now (so the cache key is now reduced to 31bit).

As a good side-effect by this change, snd_hda_codec_resume_*() will no
longer execute verbs that have been already issued during the resume
phase by checking the dirty flags.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

It's used only in one place in patch_analog.c, and it can be replaced
with others better.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When initializing the output paths, we assumed the input amps have
almost two inputs blindly.  It's not only generic but even incorrect
for some codecs like ALC268 & co.  Also, the same assumption (two
sources) exists for the bind input-amp controls.

This patch changes the codes in these places to handle the input
connections in a more generic way.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For handling the analog-loopback paths more generically, check the amp
capabilities of the aa-mixer widget, and create only the appropriate
mixer elements.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Improve the parser of analog loopback paths and handle in a more
generic way.  The following changes are included in this patch:

- Instead of assuming direct connections between pins and
  the mixer widget, track the whole path between them.  This fixes
  some missing connections like ALC660.

- Introduce the path list for loopback paths like input and output
  path lists.  Currently it's not used for any real purposes, yet.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Just like the output paths, parse the whole paths for inputs as well
and store in a path list.  For that purpose, rewrite the output parser
code to be generically usable.

The input path list is not referred at all in this patch.  It'll be
used to replace the fixed adc/capsrc array in later patches for more
flexible input path selections.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

So far, idx[i] and multi[i] indicate the attribute of the widget
path[i - 1].  This was just for simplifying the code in
__parse_output_path(), but this is rather confusing for later use.
It's more natural if both idx[i] and multi[i] point to the same widget
of path[i].  This patch changes to that way.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Simplify the output path initialization using the existing path
information instead of assuming the topology specific to Realtek
codecs.  This is also implicitly a fix for some amp values on output
pins where the old parser missed (e.g. ALC260 output pins).

The same function alc_auto_set_output_and_unmute() can be used now for
the multi-io activation, since the output selection means nothing but
activating the given output path.

And, finally at this stage, we can get rid of alc_go_down_to_selector()
and other functions that are codec really specifically to Realtek
codecs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

So far, Realtek codec driver evaluates the NIDs for volume and mute
controls twice, once while parsing the DACs and evaluating the
assignment, and another while creating the mixer elements.  This is
utterly redundant and even fragile, as it's assuming that the ctl
element evaluation is identical between both parsing DACs and creating
mixer elements.

This patch simplifies the code flow by doing the volume / mute
controls evaluation only once while parsing the DACs.  The patch ended
up in larger changes than expected because of some cleanups became
mandatory.

As a gratis bonus, this patch also fixes some cases where the stereo
channels are used wrongly for mono amps.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The mono widget is always connected to the left channel, thus the left
channel amp value also should be referred for mono widgets instead of
the right channel.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

As we parse the output paths more precisely now, we can use this path
list for parsing the widgets for volume and mute mixer controls.
The spec->vol_ctls[] and sw_ctls[] bitmasks are replaced with the
ctls[] in each output path instance.

Interestingly, this move alone automagically fixes some bugs that the
conflicting volume or mute NIDs weren't properly detected.
Also, by parsing the whole path, there are more chances to get a free
widget for volume/mute controls.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add the output path parser to Realtek codec driver as we already have
in patch_via.c.  The nid_path struct represents the complete output
path from a DAC to a pin.  The alc_spec contains an array of these
paths, and a new path is added at each time when a new DAC is
assigned.

So far, this path list is used only in limited codes: namely in this
patch, only alc_is_dac_already_used() checks the list instead of dac
arrays in all possible outputs.  In the later development, the path
list will be referred from more places, such as the mixer control
assignment / check, the mute/unmute of active routes, etc.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In the probing phase, create a list of all available DACs in the codec
and use it for checking the single DAC connections.
This list will be used in more other places in the later commits, too.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use the helper function snd_hda_get_conn_index() instead of open
codes.  This also improves the detection of some routes to DAC on
ALC260 (although the difference doesn't influence on the end
results of the mapping).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added the support for a new codec ALC284, which is compatible with
ALC269.  Also add more codec variants to handle the SSID check
properly.
Signed-off-by: NKailang Yang <kailang@realtek.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fixes the following sparse warning:
sound/usb/mixer_quirks.c:1209:23: warning:
symbol 'ebox44_table' was not declared. Should it be static?
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use correct bitmask for AES32 cards to determine wordclock lock state,
add missing bitmask for sync check and make output of the corresponding
control and /proc coherent.
Signed-off-by: NAndre Schramm <andre.schramm@iosono-sound.com>
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This reverts commit 697c373e.

The original patch was meant to remove clicking, but in fact caused even
more clicking instead.

Thanks to c4pp4 for doing most of the work with this bug.

BugLink: https://bugs.launchpad.net/bugs/886975Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

We've got a few bug reports that the runtime D3 results in the dead
HD-audio controller.  It seems that the problem is in a deeper level
than the sound driver itself, so as a temporal solution, disable the
feature for these controllers again.
Reported-and-tested-by: NVincent Blut <vincent.debian@free.fr>
Reported-and-tested-by: NMaurizio Avogadro <mavoga@gmail.com>
Cc: <stable@vger.kernel.org> [v3.7]
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The mute LED is in this case connected to the Mic1 VREF.

The machine also exposes the following string in BIOS:
"HP_Mute_LED_0_A", so if more machines are coming, it probably
makes sense to try to do something more generic, like for the
IDT codec.

Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1096789Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

vortex_wt_setdsout performs bit-negation on the bit position (wt&0x1f)
rather than on the resulting bitmask.  This code is never actually
invoked (vortex_wt_setdsout is always called with en=1), so this does
not currently cause any problem, and this patch is simply cleanup.
Signed-off-by: NNickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added a fix for hardware dependence bug where a sound card failure
should not result in reading beyond array memory index.
Signed-off-by: NAsim Kadav <kadav@cs.wisc.edu>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch is based on 3.8-rc1. It fixes two things:
1) A kernel panic caused by incorrect allocation of a u8 variable
   "bootresponse".
2) A noisy dmesg (urb status -32) caused by broken pipe to an
   invalid midi endpoint.

It is also a little cleaner because there is no need for a new
QUIRK_MIDI type as suggested by kernel developers, since the device
follows exactly the MIDIMAN protocol.
Signed-off-by: NDamien Zammit <damien@zamaudio.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Support the Creative BT-D1 Bluetooth USB audio device. Before this
patch, Linux had trouble finding the correct USB descriptors and bailed
out with these messages:

 no or invalid class specific endpoint descriptor

Now it still prints these messages on hotplug:

 snd-usb-audio: probe of ...:1.0 failed with error -5
 snd-usb-audio: probe of ...:1.2 failed with error -5
 snd-usb-audio: probe of ...:1.3 failed with error -5

But the device works correctly, including the HID support.

The patch is diff'ed against 3.8-rc1 but should apply to older kernels
as well.
Signed-off-by: NAlexander Schremmer <alex@alexanderweb.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The vmaster hook sends 1 for enabled/unmuted and 0 for disabled/muted,
but "Mute-LED Mode" being "On" refers to the LED being on, not the
volume being on.
Therefore "On" and "Off" should be switched.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Pull watchdog updates from Wim Van Sebroeck:
 "This includes some fixes and code improvements (like
  clk_prepare_enable and clk_disable_unprepare), conversion from the
  omap_wdt and twl4030_wdt drivers to the watchdog framework, addition
  of the SB8x0 chipset support and the DA9055 Watchdog driver and some
  OF support for the davinci_wdt driver."

* git://www.linux-watchdog.org/linux-watchdog: (22 commits)
  watchdog: mei: avoid oops in watchdog unregister code path
  watchdog: Orion: Fix possible null-deference in orion_wdt_probe
  watchdog: sp5100_tco: Add SB8x0 chipset support
  watchdog: davinci_wdt: add OF support
  watchdog: da9052: Fix invalid free of devm_ allocated data
  watchdog: twl4030_wdt: Change TWL4030_MODULE_PM_RECEIVER to TWL_MODULE_PM_RECEIVER
  watchdog: remove depends on CONFIG_EXPERIMENTAL
  watchdog: Convert dev_printk(KERN_<LEVEL> to dev_<level>(
  watchdog: DA9055 Watchdog driver
  watchdog: omap_wdt: eliminate goto
  watchdog: omap_wdt: delete redundant platform_set_drvdata() calls
  watchdog: omap_wdt: convert to devm_ functions
  watchdog: omap_wdt: convert to new watchdog core
  watchdog: WatchDog Timer Driver Core: fix comment
  watchdog: s3c2410_wdt: use clk_prepare_enable and clk_disable_unprepare
  watchdog: imx2_wdt: Select the driver via ARCH_MXC
  watchdog: cpu5wdt.c: add missing del_timer call
  watchdog: hpwdt.c: Increase version string
  watchdog: Convert twl4030_wdt to watchdog core
  davinci_wdt: preparation for switch to common clock framework
  ...

Pull CIFS fixes from Steve French:
 "Misc small cifs fixes"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: eliminate cifsERROR variable
  cifs: don't compare uniqueids in cifs_prime_dcache unless server inode numbers are in use
  cifs: fix double-free of "string" in cifs_parse_mount_options

Pull dm update from Alasdair G Kergon:
 "Miscellaneous device-mapper fixes, cleanups and performance
  improvements.

  Of particular note:
   - Disable broken WRITE SAME support in all targets except linear and
     striped.  Use it when kcopyd is zeroing blocks.
   - Remove several mempools from targets by moving the data into the
     bio's new front_pad area(which dm calls 'per_bio_data').
   - Fix a race in thin provisioning if discards are misused.
   - Prevent userspace from interfering with the ioctl parameters and
     use kmalloc for the data buffer if it's small instead of vmalloc.
   - Throttle some annoying error messages when I/O fails."

* tag 'dm-3.8-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: (36 commits)
  dm stripe: add WRITE SAME support
  dm: remove map_info
  dm snapshot: do not use map_context
  dm thin: dont use map_context
  dm raid1: dont use map_context
  dm flakey: dont use map_context
  dm raid1: rename read_record to bio_record
  dm: move target request nr to dm_target_io
  dm snapshot: use per_bio_data
  dm verity: use per_bio_data
  dm raid1: use per_bio_data
  dm: introduce per_bio_data
  dm kcopyd: add WRITE SAME support to dm_kcopyd_zero
  dm linear: add WRITE SAME support
  dm: add WRITE SAME support
  dm: prepare to support WRITE SAME
  dm ioctl: use kmalloc if possible
  dm ioctl: remove PF_MEMALLOC
  dm persistent data: improve improve space map block alloc failure message
  dm thin: use DMERR_LIMIT for errors
  ...

This reverts commit 79f77bf9.

This is obviously wrong, and I have no idea how I missed seeing the
warning in testing: I must just not have looked at the right logs.  The
caller bumps rq_resused/rq_next_page, so it will always be hit on a
large enough read.
Reported-by: NDave Jones <davej@redhat.com>
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull more infiniband changes from Roland Dreier:
 "Second batch of InfiniBand/RDMA changes for 3.8:
   - cxgb4 changes to fix lookup engine hash collisions
   - mlx4 changes to make flow steering usable
   - fix to IPoIB to avoid pinning dst reference for too long"

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  RDMA/cxgb4: Fix bug for active and passive LE hash collision path
  RDMA/cxgb4: Fix LE hash collision bug for passive open connection
  RDMA/cxgb4: Fix LE hash collision bug for active open connection
  mlx4_core: Allow choosing flow steering mode
  mlx4_core: Adjustments to Flow Steering activation logic for SR-IOV
  mlx4_core: Fix error flow in the flow steering wrapper
  mlx4_core: Add QPN enforcement for flow steering rules set by VFs
  cxgb4: Add LE hash collision bug fix path in LLD driver
  cxgb4: Add T4 filter support
  IPoIB: Call skb_dst_drop() once skb is enqueued for sending

Pull asm-generic cleanup from Arnd Bergmann:
 "These are a few cleanups for asm-generic:

   - a set of patches from Lars-Peter Clausen to generalize asm/mmu.h
     and use it in the architectures that don't need any special
     handling.
   - A patch from Will Deacon to remove the {read,write}s{b,w,l} as
     discussed during the arm64 review
   - A patch from James Hogan that helps with the meta architecture
     series."

* tag 'asm-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
  xtensa: Use generic asm/mmu.h for nommu
  h8300: Use generic asm/mmu.h
  c6x: Use generic asm/mmu.h
  asm-generic/mmu.h: Add support for FDPIC
  asm-generic/mmu.h: Remove unused vmlist field from mm_context_t
  asm-generic: io: remove {read,write} string functions
  asm-generic/io.h: remove asm/cacheflush.h include

Commit db5b0ae0 ("Merge tag 'dt' of git://git.kernel.org/.../arm-soc")
causes a duplicated build target.  This patch fixes it and sorts out the
build target alphabetically so that we can recognize something wrong
easily.

Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Rename stripe_map_discard to stripe_map_range and reuse it for WRITE
SAME bio processing.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

This patch removes map_info from bio-based device mapper targets.
map_info is still used for request-based targets.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Eliminate struct map_info from dm-snap.

map_info->ptr was used in dm-snap to indicate if the bio was tracked.
If map_info->ptr was non-NULL, the bio was linked in tracked_chunk_hash.

This patch removes the use of map_info->ptr. We determine if the bio was
tracked based on hlist_unhashed(&c->node). If hlist_unhashed is true,
the bio is not tracked, if it is false, the bio is tracked.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

This patch removes endio_hook_pool from dm-thin and uses per-bio data instead.

This patch removes any use of map_info in preparation for the next patch
that removes map_info from bio-based device mapper.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>