Change to using a configurable RAM setup in startup code. This cleans up
the whole RAM base/sizing issue, and removes a lot of board specific code.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Remove the fixed RAM configurations for each board type from the
linker script. Replace with simple defines usng the flexible RAM
configuration options. This cleans out of lot of board specific
munging of addresses.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Reworked the way RAM regions are defined. Instead of coding all the
variations for each board type we now just configure RAM base and size
in the usual Kconfig setup. This much simplifies the code, and makes it
a lot more flexible when setting up new boards or board varients.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Clean out unused variable definitions from 68328 start up code.
Also use a more appropriate start address for the case of relocating
the kernel code to RAM (from ROM/flash).
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

__ramvec has been removed from the linker script. The vector base
address is defined as a configurable option, use that. Remove its
use from the 68328/pilot startup code.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (4227): Update this driver for recent header file movement.
  V4L/DVB (4223): Add V4L2_CID_MPEG_STREAM_VBI_FMT control
  V4L/DVB (4222): Always switch tuner mode when calling VIDIOC_S_FREQUENCY.
  V4L/DVB (4221): Add HM12 YUV format define.
  V4L/DVB (4219): Av7110: analog sound output of DVB-C rev 2.3
  V4L/DVB (4217): Fix a misplaced closing bracket/else, which caused swzigzag not to be called
  V4L/DVB (4215): Make VIDEO_CX88_BLACKBIRD a separate build option
  V4L/DVB (4214): Make VIDEO_CX2341X a selectable build option
  V4L/DVB (4213): Cx88: cleanups
  V4L/DVB (4211): Fix an Oops for all fe that have get_frontend_algo == NULL

* x86-64: (83 commits)
  [PATCH] x86_64: x86_64 stack usage debugging
  [PATCH] x86_64: (resend) x86_64 stack overflow debugging
  [PATCH] x86_64: msi_apic.c build fix
  [PATCH] x86_64: i386/x86-64 Add nmi watchdog support for new Intel CPUs
  [PATCH] x86_64: Avoid broadcasting NMI IPIs
  [PATCH] x86_64: fix apic error on bootup
  [PATCH] x86_64: enlarge window for stack growth
  [PATCH] x86_64: Minor string functions optimizations
  [PATCH] x86_64: Move export symbols to their C functions
  [PATCH] x86_64: Standardize i386/x86_64 handling of NMI_VECTOR
  [PATCH] x86_64: Fix modular pc speaker
  [PATCH] x86_64: remove sys32_ni_syscall()
  [PATCH] x86_64: Do not use -ffunction-sections for modules
  [PATCH] x86_64: Add cpu_relax to apic_wait_icr_idle
  [PATCH] x86_64: adjust kstack_depth_to_print default
  [PATCH] i386/x86-64: adjust /proc/interrupts column headings
  [PATCH] x86_64: Fix race in cpu_local_* on preemptible kernels
  [PATCH] x86_64: Fix fast check in safe_smp_processor_id
  [PATCH] x86_64: x86_64 setup.c - printing cmp related boottime information
  [PATCH] i386/x86-64/ia64: Move polling flag into thread_info_status
  ...

Manual resolve of trivial conflict in arch/i386/kernel/Makefile

Applies to git & 2.6.17-rc6 after CONFIG_DEBUG_STACKOVERFLOW patch

uses same stack-zeroing mechanism as on i386 to discover maximum stack
excursions.
Signed-off-by: NEric Sandeen <sandeen@sgi.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Take two, now without spurious whitespace :(  Applies to git & 2.6.17-rc6

CONFIG_DEBUG_STACKOVERFLOW existed for x86_64 in 2.4, but seems to have gone AWOL in 2.6.

I've pretty much just copied this over from the 2.4 code, with
appropriate tweaks for the 2.6 kernel, plus a bugfix.  I'd personally
rather see it printed out the way other arches do it, i.e.
bytes-remaining-until-overflow, rather than having to do the subtraction
yourself.  Also, only 128 bytes remaining seems awfully late to issue a
warning.  But I'll start here :)
Signed-off-by: NEric Sandeen <sandeen@sgi.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

      CC      drivers/pci/msi-apic.o
In file included from include/asm/msi.h:11,
                  from drivers/pci/msi.h:71,
                  from drivers/pci/msi-apic.c:8:
include/asm/smp.h:103: error: syntax error before '->' token

akpm: nasty.  It appears to be

  static inline unsigned int cpu_mask_to_apicid(cpumask_t cpumask)

conflicting with include/asm-x86_64/mach_apic.h's

  #define cpu_mask_to_apicid (genapic->cpu_mask_to_apicid)

And I don't know which patch in rc4-mm1 triggered this.

Fixing this in the .c file seems wrong.

Including asm/smp.h instead of linux/smp.h seems wrong too.  Need that
.config.

Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Intel now has support for Architectural Performance Monitoring Counters
( Refer to IA-32 Intel Architecture Software Developer's Manual
http://www.intel.com/design/pentium4/manuals/253669.htm ). This
feature is present starting from Intel Core Duo and Intel Core Solo processors.

What this means is, the performance monitoring counters and some performance
monitoring events are now defined in an architectural way (using cpuid).
And there will be no need to check for family/model etc for these architectural
events.

Below is the patch to use this performance counters in nmi watchdog driver.
Patch handles both i386 and x86-64 kernels.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

On some i386/x86_64 systems, sending an NMI IPI as a broadcast will
reset the system.  This seems to be a BIOS bug which affects machines
where one or more cpus are not under OS control.  It occurs on HT
systems with a version of the OS that is not compiled without HT
support.  It also occurs when a system is booted with max_cpus=n where
2 <= n < cpus known to the BIOS.  The fix is to always send NMI IPI as
a mask instead of as a broadcast.
Signed-off-by: NKeith Owens <kaos@sgi.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Appended patch fixes the "APIC error on CPUX: 00(40)" observed during bootup.

From SDM Vol-3A "Valid Interrupt Vectors" section:
	"When an illegal vector value (0-15) is written to an LVT entry
	and the delivery mode is Fixed, the APIC may signal an illegal
	vector error, with out regard to whether the mask bit is set
	or whether an interrupt is actually seen on input."
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Allow stack growth so the 'enter' instruction works.  Also
fixes problem in compat_sys_kexec_load() which could allocate
more than 128 bytes using compat_alloc_user_space().
Signed-off-by: NChuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

 - Use tail call from clear_user to __clear_user to save some code size
 - Use standard memcpy for forward memmove
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Only exports for assembler files are left in x8664_ksyms.c

Originally inspired by a patch from Al Viro
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

x86_64 and i386 behave inconsistently when sending an IPI on vector 2
(NMI_VECTOR).  Make both behave the same, so IPI 2 is sent as NMI.

The crash code was abusing send_IPI_allbutself() by passing a code
instead of a vector, it only worked because crash knew about the
internal code of send_IPI_allbutself().  Change crash to use NMI_VECTOR
instead, and remove the comment about how crash was abusing the function.

This patch is a pre-requisite for fixing the problem where sending an
IPI as NMI would reboot some Dell Xeon systems.  I cannot fix that
problem while crash continus to abuse send_IPI_allbutself().

It also removes the inconsistency between i386 and x86_64 for
NMI_VECTOR.  That will simplify all the RAS code that needs to bring
all the cpus to a clean stop, even when one or more cpus are spinning
disabled.
Signed-off-by: NKeith Owens <kaos@sgi.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It turned out that the following change is needed when the speaker is
compiled as a module.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch removes the no longer used sys32_ni_syscall()
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Currently CONFIG_REORDER uses -ffunction-sections for all code;
however, creating a separate section for each function is not useful
for modules and just adds bloat.  Moving this option from CFLAGS to
CFLAGS_KERNEL shrinks module object files (e.g., the module tree for a
kernel built with most drivers as modules shrinked from 54M to 46M),
and decreases the number of sysfs files in /sys/module/*/sections/
directories.
Signed-off-by: NSergey Vlasov <vsu@altlinux.ru>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This one is adding a cpu_relax() that already existed in the i386 version.
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Defaulting to a value not evenly divisible by four makes little sense,
as four values are displayed per line (and hence the rest of the line
would otherwise be wasted).
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

With (significantly) more than 10 CPUs online, the column headings
drifted off the positions of the column contents with growing CPU
numbers.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When a process changes CPUs while doing the non atomic cpu_local_*
operations it might operate on the local_t of a different CPUs.

Fix that by disabling preemption.

Pointed out by Christopher Lameter
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The APIC ID returned by hard_smp_processor_id can be beyond
NR_CPUS and then overflow the x86_cpu_to_apic[] array.

Add a check for overflow. If it happens then the slow loop below
will catch.

Bug pointed out by Doug Thompson
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Getting phys_proc_id and cpu_core_id information to be printed at boot
time for AMD processors.  Also matching the Node related boot time
information that gets printed for Intel and AMD processors for NUMA
configurations.
Signed-off-by: NRohit Seth <rohitseth@google.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

During some profiling I noticed that default_idle causes a lot of
memory traffic. I think that is caused by the atomic operations
to clear/set the polling flag in thread_info. There is actually
no reason to make this atomic - only the idle thread does it
to itself, other CPUs only read it. So I moved it into ti->status.

Converted i386/x86-64/ia64 for now because that was the easiest
way to fix ACPI which also manipulates these flags in its idle
function.

Cc: Nick Piggin <npiggin@novell.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

No red zone possible/needed on the alternative stack.

It caused confusion.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

 - Use DMA_32BIT_MASK

 - Use %z for size_t

 - 80-cols

Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

 - fix an off-by-one error in phys_pmd_init()
 - prevent phys_pmd_init() from removing mappings established earlier
 - fix the direct mapping early printk to in fact show the end of the range
 - remove an apparently orphan comment
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Cc: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Clean up mce_amd.c for readability and remove code no
longer needed.
Signed-off-by: NJacob Shin <jacob.shin@amd.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add support for mce threshold registers found in future
AMD family 0x10 processors.  Backwards compatible with
family 0xF hardware.

AK: fixed build on !SMP
Signed-off-by: NJacob Shin <jacob.shin@amd.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Get rid of /sys/devices/system/threshold directory and move
mce_amd thresholding files into the machine sysfs directory --
/sys/devices/system/machinecheck.

AK: Fixed warning
Signed-off-by: NJacob Shin <jacob.shin@amd.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add support for extended APIC LVT found in future AMD processors.
Signed-off-by: NJacob Shin <jacob.shin@amd.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Architecture specific configs like this have no business at all
in init/Kconfig. This prevents it from being set on x86-64

Pointed out by H.Peter Anvin
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It's like this on SUSE systems.

Cc: hpa@zytor.com
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Update my copyright dates in arch/x86-64/kernel/time.c
Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

After writing the CFG register, the first value written to the T0_CMP
register is the value at which next interrupt should be triggered, every
value after that sets the period of the interrupt. For that reason, the code
needs to write the value twice - to set both the phase and period.

[AK: I had already figured it out by myself, but it's still useful
to have a comment for this.]
Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch makes use of the newly added conversion constants
in time.h to x86-64 time.c. The code gets significantly easier
to understand.
Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>