Implements to support GET and SET operations of the DME.
These operations are used to configure the behavior of
the UNIPRO. Along with basic operation, {Peer/AttrSetType}
can be mixed.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NSubhash Jadavani <subhashj@codeaurora.org>
Tested-by: NYaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: NSantosh Y <santoshsy@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

IACTH(Interrupt aggregation counter threshold) value is allowed
up to 0x1F and current setting value is the maximum.
This value is related with NUTRS(max:0x20) of HCI's capability.
Considering HCI controller doesn't support the maximum, IACTH
setting should be adjusted with possible value.
For that, existing 'ufshcd_config_int_aggr' is split into two part
[reset, configure].
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NSubhash Jadavani <subhashj@codeaurora.org>
Tested-by: NYaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: NSantosh Y <santoshsy@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Unlike 'GOOD' and 'CHECK CONDITION', other status values in
Response UPIU may or may not contain sense data. That is returning
sense data isn't obvious. So, in this case the Data Segment Length
field should be checked. If a non-zero value, it means that UPIU
has Sense Data in the Data Segment area.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NSubhash Jadavani <subhashj@codeaurora.org>
Tested-by: NYaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: NSantosh Y <santoshsy@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Right now the Makefile for the mpt3sas driver does not even allow the
driver to be built into the kernel.  So fix that up, as there doesn't
seem to be any obvious reason why this shouldn't be done.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NSreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This fixes an issue seen with devices getting marked offline
in a scenario where a VIOS was getting rebooted while a
client VFC adapter is in SCSI EH and prevents unnecessary
EH escalation in some scenarios.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Acked-by: NRobert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The hypervisor is big endian, so little endian kernel builds need
to byteswap.

[jejb: fix checkpatch errors]
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Reported-by: NDave Jones <davej@redhat.com>
Signed-off-by: NBradley Grove <bgrove@attotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NBradley Grove <bgrove@attotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NBradley Grove <bgrove@attotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NBradley Grove <bgrove@attotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NBradley Grove <bgrove@attotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NBradley Grove <bgrove@attotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Push file descriptor list locking down to per-device locking. Let sg_index_lock
only protect device lookup.
sdp->detached is also set and checked with this lock held.
Signed-off-by: NVaughan Cao <vaughan.cao@oracle.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

@Detached is set under the protection of sg_index_lock. Without getting the
lock, new sfp will be added during sg removal and there is no chance for it
to be picked out. So check with sg_index_lock held in sg_add_sfp().
Signed-off-by: NVaughan Cao <vaughan.cao@oracle.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Open exclusive check is protected by o_sem, no need sg_open_exclusive_lock.
@exclude is used to record which type of rwsem we are holding.
Signed-off-by: NVaughan Cao <vaughan.cao@oracle.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

A race condition may happen if two threads are both trying to open the same sg
with O_EXCL simultaneously. It's possible that they both find fsds list is
empty and get_exclude(sdp) returns 0, then they both call set_exclude() and
break out from wait_event_interruptible and resume open.

Now use rwsem to protect this process. Exclusive open gets write lock and
others get read lock. The lock will be held until file descriptor is closed.
This also leads 'exclude' only a status rather than a check mark.
Signed-off-by: NVaughan Cao <vaughan.cao@oracle.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Commit b90ebc3d ("[SCSI] scsi_debug:
fix logical block provisioning support") fixed several issues with
logical block provisioning support, but it still doesn't properly fix
the cases when unmap_alignment > 0.

For example, load scsi_debug module with the following module parameters
and make all blocks mapped by filling the storage with zero.

        # modprobe scsi_debug lbpu=1 unmap_alignment=1 unmap_granularity=4
        # dd if=/dev/zero of=$DEV

Then, try to unmap the first unmappable blocks at lba=1, but GET LBA STATUS
unexpectedly reports that the last UNMAP has done nothing.

        # sg_unmap --lba=1 --num=4 $DEV
        # sg_get_lba_status --lba=1 $DEV
        descriptor LBA: 0x0000000000000001  blocks: 16383  mapped

The problem is in map_index_to_lba(), which should return the first
LBA which is corresponding to a given index of provisioning map
(map_storep).
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Acked-by: N"Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

With module parameter num_parts > 0, partition table is built on the
ramdisk storage when loading the driver.  Unfortunately, there is an
endianness bug in sdebug_build_parts().  So the partition table is not
correctly initialized on big-endian systems.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Tested-by: NMartin Peschke <mpeschke@linux.vnet.ibm.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

At mailbox/buffer debug level, print the correct values of the
outgoing and incoming mailbox registers.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

On any Adapter when we flash through FC/FCoE without card reset option it still
shows the Running FW version in Flashed FW version. This new interface will be
used by API to instruct the driver to update its cache versions.
Signed-off-by: NSawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Unless there is a need to observe them, the queue depth ramp up/down messages
are a nuisance and may cause the system to become unresponsive so move it a
non-default logging level.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Earlier IDC-TIME-EXTEND aen was a nop and ignored by driver.
We now have to handle the aen so that other protocol drivers can use time
extension during some loopback operations.
Signed-off-by: NSantosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Set default critical temperature value in cases when ISPFX00 firmware doesn't provide it
Signed-off-by: NArmen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: QLAFX00 make over temperature AEN handling informational, add log for normal temperature AEN
Signed-off-by: NArmen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NArmen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NArmen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NArmen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NArmen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NArmen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Add the missing FCP statistics to sysfs.
Add reset FCP statistics functionality via sysfs.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

[SCSI] qla2xxx: Make log message that prints when a completion status requires a port down more readable.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NArmen Baloyan <armen.baloyan@qlogic.com>
Acked-by: NSrinivasa Rao <srinivasa.rao@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NArmen Baloyan <armen.baloyan@qlogic.com>
Acked-by: NSrinivasa Rao <srinivasa.rao@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

For supported ISPS, Read asic temperature by calling the
GET PARAMS (type C) mailbox command.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>