Clean up standard header text and remove unused #define.
Signed-off-by: NSteven J. Hill <sjhill@mips.com>
Patchwork: http://patchwork.linux-mips.org/patch/4703/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

On a multi-chip XLP board, each node can have 4 PCIe links. Update
XLP PCI code to initialize PCIe on all the nodes.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4803/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

On multi-chip boards, the first core on slave SoCs may take much
more time to wakeup. Add code to wait for the core to come up before
proceeding with the rest of the boot up.

Update xlp_wakeup_core to also skip the boot node and the boot CPU
initialization which is already complete.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4783/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Doing calibrate delay on a hardware thread will be inaccurate since
it depends on the load on other threads in the core. It will also
slow down the boot process when done for 128 hardware threads. Switch
to a pre-computed loops per jiffy based on the core frequency. The
value is computed based on the core frequency and roughly matches the
value calculated by calibrate_delay().
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4791/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

TLB and COP0 hazards are handled in hardware for Netlogic XLR/XLS
SoCs. Update hazards.h to pick more optimal set of definitions when
compiling for XLR/XLS.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4788/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Reading PCI extended register at 0x255 on a bridge will hang if there
is no device connected on the link. Make PCI read routine skip this
register.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4789/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

The XLR/XLS/XLP PIC has a 8 countdown timers which run at the PIC
frequencey. One of these can be used as a clocksource to provide
timestamps that is common across cores. This can be used in place
of the count/compare clocksource which is per-CPU.

On XLR/XLS PIC registers are 32-bit, so we just use the lower 32-bits
of the PIC counter. On XLP, the whole 64-bit can be used.

Provide common macros and functions for PIC timer registers on XLR/XLS
and XLP, and use them to register a PIC clocksource.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4786/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Since we now use r4k cache code for Netlogic XLP, it is
better to split L1 icache among the active threads, so that
threads won't step on each other while flushing icache.

The L1 dcache is already split among the threads in the core.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4787/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Rename function xlp_enable_pci_bswap() to xlp_config_pci_bswap(), which
is a better description for its functionality.  When compiled in
big-endian mode, xlp_config_pci_bswap() will configure the PCIe links
to byteswap.  In little-endian mode, no swap configuration is needed
for the PCIe controller, and the function is empty.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4802/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Provide functions ack_c0_eirr(), set_c0_eimr(), clear_c0_eimr()
and read_c0_eirr_and_eimr() that do the EIMR and EIRR operations
and update the interrupt handling code to use these functions.
Also, use the EIMR register functions to mask interrupts in the
irq code.

The 64-bit interrupt request and mask registers (EIRR and EIMR) are
accessed when the interrupts are off, and the common operations are
to set or clear a bit in these registers. Using the 64-bit c0 access
functions for these operations is not optimal in 32-bit, because it
will disable/restore interrupts and split/join the 64-bit value during
each register access.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4790/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Add support for XLS6xx CPUs to the Fast Message Network (FMN)
configuration.
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4785/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

This code makes the irqs used by the EIU loadable from the DT. Additionally we
add a helper that allows the pinctrl layer to map external irqs to real irq
numbers.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4818/

We need to make sure that the reset gpio is available and also set a sane
default state.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4817/

Explicitly enable the clock gate of the internal GPHYs found on xrx200.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4816/

The Lantiq DSL SoCs have an internal networking processor. Add code to read
the static clock rate.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4815/

"nodes" is written with a single "s"
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4814/

Make sure 24KEc is properly identified inside /proc/cpuinfo
Signed-off-by: NJohn Crispin <blogic@openwrt.org>

An SoC normally do not define path variables for board_rev and
board_type and the Broadcom SDK also uses the nvram values without a
prefix in such cases. Do the same to fill these sprom attributes from
nvram and do not leave them empty, because brcmsmac do not like this.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4679/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

The kernel is loaded to 0x80001000 so there is some space left for the
exception handlers and the kernel do not have to reserve some extra
space for them.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4747/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

All the boot loaders I have seen are booting the kernel in raw mode by
default. CFE seems to support elf kernel images too, but the default
case is raw for the devices I know of. Select this option to make the
kernel boot on most of the devices with the default options.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4746/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Some nvram values on some devices have a newline character at the end
of the value, that caused read errors. Trim the string before reading
the number.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4745/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

The nvram functions are exported and used by some normal drivers. To
prevent name clashes with ofter parts of the kernel code add a bcm47xx_
prefix in front of the function names and the header file name.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4744/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

The old code just worked for nvram with a size of 0x8000 bytes. This
patch adds support for reading nvram from partitions of 0xF000 and
0x10000 bytes.

There is just 32KB space for the nvram, but most devices do not use the
full size and this code reads the first 32KB in that case and prints a
warning.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4743/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4742/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4741/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

This makes it possible to handle the case of not being able to read the
nvram ram. This could happen when the code searching for the specific
flash chip have not run jet.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4740/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Instead of using our own error codes use some common codes.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4739/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Also check if parallel flash is present at all before accessing it and
add support for serial flash on BCMA bus.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4738/Signed-off-by: NJohn Crispin <blogic@openwrt.org>

Pull ARM fixes from Russell King:
 "I was going to hold these off until v3.8 was out, and send them with a
  stable tag, but as everyone else is pushing much bigger fixes which
  Linus is accepting, let's save people from the hastle of having to
  patch v3.8 back into working or use a stable kernel.

  Looking at the diffstat, this really is high value for its size; this
  is miniscule compared to how the -rc6 to tip diffstat currently looks.

  So, four patches in this set:
   - Punit Agrawal reports that the kernel no longer boots on MPCore due
     to a new assumption made in the GIC code which isn't true of
     earlier GIC designs.  This is the biggest change in this set.
   - Punit's boot log also revealed a bunch of WARN_ON() dumps caused by
     the DT-ification of the GIC support without fixing up non-DT
     Realview - which now sees a greater number of interrupts than it
     did before.
   - A fix for the DMA coherent code from Marek which uses the wrong
     check for atomic allocations; this can result in spinlock lockups
     or other nasty effects.
   - A fix from Will, which will affect all Android based platforms if
     not applied (which use the 2G:2G VM split) - this causes
     particularly 'make' to misbehave unless this bug is fixed."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7641/1: memory: fix broken mmap by ensuring TASK_UNMAPPED_BASE is aligned
  ARM: DMA mapping: fix bad atomic test
  ARM: realview: ensure that we have sufficient IRQs available
  ARM: GIC: fix GIC cpumask initialization

Pull networking fixes from David Miller:

 1) Revert iwlwifi reclaimed packet tracking, it causes problems for a
    bunch of folks.  From Emmanuel Grumbach.

 2) Work limiting code in brcmsmac wifi driver can clear tx status
    without processing the event.  From Arend van Spriel.

 3) rtlwifi USB driver processes wrong SKB, fix from Larry Finger.

 4) l2tp tunnel delete can race with close, fix from Tom Parkin.

 5) pktgen_add_device() failures are not checked at all, fix from Cong
    Wang.

 6) Fix unintentional removal of carrier off from tun_detach(),
    otherwise we confuse userspace, from Michael S.  Tsirkin.

 7) Don't leak socket reference counts and ubufs in vhost-net driver,
    from Jason Wang.

 8) vmxnet3 driver gets it's initial carrier state wrong, fix from Neil
    Horman.

 9) Protect against USB networking devices which spam the host with 0
    length frames, from Bjørn Mork.

10) Prevent neighbour overflows in ipv6 for locally destined routes,
    from Marcelo Ricardo.  This is the best short-term fix for this, a
    longer term fix has been implemented in net-next.

11) L2TP uses ipv4 datagram routines in it's ipv6 code, whoops.  This
    mistake is largely because the ipv6 functions don't even have some
    kind of prefix in their names to suggest they are ipv6 specific.
    From Tom Parkin.

12) Check SYN packet drops properly in tcp_rcv_fastopen_synack(), from
    Yuchung Cheng.

13) Fix races and TX skb freeing bugs in via-rhine's NAPI support, from
    Francois Romieu and your's truly.

14) Fix infinite loops and divides by zero in TCP congestion window
    handling, from Eric Dumazet, Neal Cardwell, and Ilpo Järvinen.

15) AF_PACKET tx ring handling can leak kernel memory to userspace, fix
    from Phil Sutter.

16) Fix error handling in ipv6 GRE tunnel transmit, from Tommi Rantala.

17) Protect XEN netback driver against hostile frontend putting garbage
    into the rings, don't leak pages in TX GOP checking, and add proper
    resource releasing in error path of xen_netbk_get_requests().  From
    Ian Campbell.

18) SCTP authentication keys should be cleared out and released with
    kzfree(), from Daniel Borkmann.

19) L2TP is a bit too clever trying to maintain skb->truesize, and ends
    up corrupting socket memory accounting to the point where packet
    sending is halted indefinitely.  Just remove the adjustments
    entirely, they aren't really needed.  From Eric Dumazet.

20) ATM Iphase driver uses a data type with the same name as the S390
    headers, rename to fix the build.  From Heiko Carstens.

21) Fix a typo in copying the inner network header offset from one SKB
    to another, from Pravin B Shelar.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits)
  net: sctp: sctp_endpoint_free: zero out secret key data
  net: sctp: sctp_setsockopt_auth_key: use kzfree instead of kfree
  atm/iphase: rename fregt_t -> ffreg_t
  net: usb: fix regression from FLAG_NOARP code
  l2tp: dont play with skb->truesize
  net: sctp: sctp_auth_key_put: use kzfree instead of kfree
  netback: correct netbk_tx_err to handle wrap around.
  xen/netback: free already allocated memory on failure in xen_netbk_get_requests
  xen/netback: don't leak pages on failure in xen_netbk_tx_check_gop.
  xen/netback: shutdown the ring if it contains garbage.
  net: qmi_wwan: add more Huawei devices, including E320
  net: cdc_ncm: add another Huawei vendor specific device
  ipv6/ip6_gre: fix error case handling in ip6gre_tunnel_xmit()
  tcp: fix for zero packets_in_flight was too broad
  brcmsmac: rework of mac80211 .flush() callback operation
  ssb: unregister gpios before unloading ssb
  bcma: unregister gpios before unloading bcma
  rtlwifi: Fix scheduling while atomic bug
  net: usbnet: fix tx_dropped statistics
  tcp: ipv6: Update MIB counters for drops
  ...

Daniel Borkmann says:

====================
Cryptographically used keys should be zeroed out when our session
ends resp. memory is freed, thus do not leave them somewhere in the
memory.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On sctp_endpoint_destroy, previously used sensitive keying material
should be zeroed out before the memory is returned, as we already do
with e.g. auth keys when released.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In sctp_setsockopt_auth_key, we create a temporary copy of the user
passed shared auth key for the endpoint or association and after
internal setup, we free it right away. Since it's sensitive data, we
should zero out the key before returning the memory back to the
allocator. Thus, use kzfree instead of kfree, just as we do in
sctp_auth_key_put().
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have conflicting type qualifiers for "freg_t" in s390's ptrace.h and the
iphase atm device driver, which causes the compile error below.
Unfortunately the s390 typedef can't be renamed, since it's a user visible api,
nor can I change the include order in s390 code to avoid the conflict.

So simply rename the iphase typedef to a new name. Fixes this compile error:

In file included from drivers/atm/iphase.c:66:0:
drivers/atm/iphase.h:639:25: error: conflicting type qualifiers for 'freg_t'
In file included from next/arch/s390/include/asm/ptrace.h:9:0,
                 from next/arch/s390/include/asm/lowcore.h:12,
                 from next/arch/s390/include/asm/thread_info.h:30,
                 from include/linux/thread_info.h:54,
                 from include/linux/preempt.h:9,
                 from include/linux/spinlock.h:50,
                 from include/linux/seqlock.h:29,
                 from include/linux/time.h:5,
                 from include/linux/stat.h:18,
                 from include/linux/module.h:10,
                 from drivers/atm/iphase.c:43:
next/arch/s390/include/uapi/asm/ptrace.h:197:3: note: previous declaration of 'freg_t' was here
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Nchas williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have received multiple reports of mmap failures when running with a
2:2 vm split. These manifest as either -EINVAL with a non page-aligned
address (ending 0xaaa) or a SEGV, depending on the application. The
issue is commonly observed in children of make, which appears to use
bottom-up mmap (assumedly because it changes the stack rlimit).

Further investigation reveals that this regression was triggered by
394ef640 ("mm: use vm_unmapped_area() on arm architecture"), whereby
TASK_UNMAPPED_BASE is no longer page-aligned for bottom-up mmap, causing
get_unmapped_area to choke on misaligned addressed.

This patch fixes the problem by defining TASK_UNMAPPED_BASE in terms of
TASK_SIZE and explicitly aligns the result to 16M, matching the other
end of the heap.
Acked-by: NNicolas Pitre <nico@linaro.org>
Reported-by: NSteve Capper <steve.capper@arm.com>
Reported-by: NJean-Francois Moine <moinejf@free.fr>
Reported-by: NChristoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Realview fails to boot with this warning:
BUG: spinlock lockup suspected on CPU#0, init/1
 lock: 0xcf8bde10, .magic: dead4ead, .owner: init/1, .owner_cpu: 0
Backtrace:
[<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:cf8bde10 r5:cf83d1c0 r4:cf8bde10 r3:cf83d1c0
[<c03294d0>] (dump_stack+0x0/0x1c) from [<c018926c>] (spin_dump+0x84/0x98)
[<c01891e8>] (spin_dump+0x0/0x98) from [<c0189460>] (do_raw_spin_lock+0x100/0x198)
[<c0189360>] (do_raw_spin_lock+0x0/0x198) from [<c032cbac>] (_raw_spin_lock+0x3c/0x44)
[<c032cb70>] (_raw_spin_lock+0x0/0x44) from [<c01c9224>] (pl011_console_write+0xe8/0x11c)
[<c01c913c>] (pl011_console_write+0x0/0x11c) from [<c002aea8>] (call_console_drivers.clone.7+0xdc/0x104)
[<c002adcc>] (call_console_drivers.clone.7+0x0/0x104) from [<c002b320>] (console_unlock+0x2e8/0x454)
[<c002b038>] (console_unlock+0x0/0x454) from [<c002b8b4>] (vprintk_emit+0x2d8/0x594)
[<c002b5dc>] (vprintk_emit+0x0/0x594) from [<c0329718>] (printk+0x3c/0x44)
[<c03296dc>] (printk+0x0/0x44) from [<c002929c>] (warn_slowpath_common+0x28/0x6c)
[<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029304>] (warn_slowpath_null+0x24/0x2c)
[<c00292e0>] (warn_slowpath_null+0x0/0x2c) from [<c0070ab0>] (lockdep_trace_alloc+0xd8/0xf0)
[<c00709d8>] (lockdep_trace_alloc+0x0/0xf0) from [<c00c0850>] (kmem_cache_alloc+0x24/0x11c)
[<c00c082c>] (kmem_cache_alloc+0x0/0x11c) from [<c00bb044>] (__get_vm_area_node.clone.24+0x7c/0x16c)
[<c00bafc8>] (__get_vm_area_node.clone.24+0x0/0x16c) from [<c00bb7b8>] (get_vm_area_caller+0x48/0x54)
[<c00bb770>] (get_vm_area_caller+0x0/0x54) from [<c0020064>] (__alloc_remap_buffer.clone.15+0x38/0xb8)
[<c002002c>] (__alloc_remap_buffer.clone.15+0x0/0xb8) from [<c0020244>] (__dma_alloc+0x160/0x2c8)
[<c00200e4>] (__dma_alloc+0x0/0x2c8) from [<c00204d8>] (arm_dma_alloc+0x88/0xa0)[<c0020450>] (arm_dma_alloc+0x0/0xa0) from [<c00beb00>] (dma_pool_alloc+0xcc/0x1a8)
[<c00bea34>] (dma_pool_alloc+0x0/0x1a8) from [<c01a9d14>] (pl08x_fill_llis_for_desc+0x28/0x568)
[<c01a9cec>] (pl08x_fill_llis_for_desc+0x0/0x568) from [<c01aab8c>] (pl08x_prep_slave_sg+0x258/0x3b0)
[<c01aa934>] (pl08x_prep_slave_sg+0x0/0x3b0) from [<c01c9f74>] (pl011_dma_tx_refill+0x140/0x288)
[<c01c9e34>] (pl011_dma_tx_refill+0x0/0x288) from [<c01ca748>] (pl011_start_tx+0xe4/0x120)
[<c01ca664>] (pl011_start_tx+0x0/0x120) from [<c01c54a4>] (__uart_start+0x48/0x4c)
[<c01c545c>] (__uart_start+0x0/0x4c) from [<c01c632c>] (uart_start+0x2c/0x3c)
[<c01c6300>] (uart_start+0x0/0x3c) from [<c01c795c>] (uart_write+0xcc/0xf4)
[<c01c7890>] (uart_write+0x0/0xf4) from [<c01b0384>] (n_tty_write+0x1c0/0x3e4)
[<c01b01c4>] (n_tty_write+0x0/0x3e4) from [<c01acfe8>] (tty_write+0x144/0x240)
[<c01acea4>] (tty_write+0x0/0x240) from [<c01ad17c>] (redirected_tty_write+0x98/0xac)
[<c01ad0e4>] (redirected_tty_write+0x0/0xac) from [<c00c371c>] (vfs_write+0xbc/0x150)
[<c00c3660>] (vfs_write+0x0/0x150) from [<c00c39c0>] (sys_write+0x4c/0x78)
[<c00c3974>] (sys_write+0x0/0x78) from [<c0014460>] (ret_fast_syscall+0x0/0x3c)

This happens because the DMA allocation code is not respecting atomic
allocations correctly.

GFP flags should not be tested for GFP_ATOMIC to determine if an
atomic allocation is being requested.  GFP_ATOMIC is not a flag but
a value.  The GFP bitmask flags are all prefixed with __GFP_.

The rest of the kernel tests for __GFP_WAIT not being set to indicate
an atomic allocation.  We need to do the same.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Realview EB with a rev B MPcore tile results in lots of warnings at
boot because it can't allocate enough IRQs.  Fix this by increasing
the number of available IRQs.

WARNING: at /home/rmk/git/linux-rmk/arch/arm/common/gic.c:757 gic_init_bases+0x12c/0x2ec()
Cannot allocate irq_descs @ IRQ96, assuming pre-allocated
Modules linked in:
Backtrace:
[<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:000002f5 r5:c042c62c r4:c044ff40 r3:c045f240
[<c03294d0>] (dump_stack+0x0/0x1c) from [<c00292c8>] (warn_slowpath_common+0x54/0x6c)
[<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029384>] (warn_slowpath_fmt+0x38/0x40)
[<c002934c>] (warn_slowpath_fmt+0x0/0x40) from [<c042c62c>] (gic_init_bases+0x12c/0x2ec)
[<c042c500>] (gic_init_bases+0x0/0x2ec) from [<c042cdc8>] (gic_init_irq+0x8c/0xd8)
[<c042cd3c>] (gic_init_irq+0x0/0xd8) from [<c042827c>] (init_IRQ+0x1c/0x24)
[<c0428260>] (init_IRQ+0x0/0x24) from [<c04256c8>] (start_kernel+0x1a4/0x300)
[<c0425524>] (start_kernel+0x0/0x300) from [<70008070>] (0x70008070)
---[ end trace 1b75b31a2719ed1c ]---
------------[ cut here ]------------
WARNING: at /home/rmk/git/linux-rmk/kernel/irq/irqdomain.c:234 irq_domain_add_legacy+0x80/0x140()
Modules linked in:
Backtrace:
[<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:000000ea r5:c0081a38 r4:00000000 r3:c045f240
[<c03294d0>] (dump_stack+0x0/0x1c) from [<c00292c8>] (warn_slowpath_common+0x54/0x6c)
[<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029304>] (warn_slowpath_null+0x24/0x2c)
[<c00292e0>] (warn_slowpath_null+0x0/0x2c) from [<c0081a38>] (irq_domain_add_legacy+0x80/0x140)
[<c00819b8>] (irq_domain_add_legacy+0x0/0x140) from [<c042c64c>] (gic_init_bases+0x14c/0x2ec)
[<c042c500>] (gic_init_bases+0x0/0x2ec) from [<c042cdc8>] (gic_init_irq+0x8c/0xd8)
[<c042cd3c>] (gic_init_irq+0x0/0xd8) from [<c042827c>] (init_IRQ+0x1c/0x24)
[<c0428260>] (init_IRQ+0x0/0x24) from [<c04256c8>] (start_kernel+0x1a4/0x300)
[<c0425524>] (start_kernel+0x0/0x300) from [<70008070>] (0x70008070)
---[ end trace 1b75b31a2719ed1d ]---
------------[ cut here ]------------
WARNING: at /home/rmk/git/linux-rmk/arch/arm/common/gic.c:762 gic_init_bases+0x170/0x2ec()
Modules linked in:
Backtrace:
[<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:000002fa r5:c042c670 r4:00000000 r3:c045f240
[<c03294d0>] (dump_stack+0x0/0x1c) from [<c00292c8>] (warn_slowpath_common+0x54/0x6c)
[<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029304>] (warn_slowpath_null+0x24/0x2c)
[<c00292e0>] (warn_slowpath_null+0x0/0x2c) from [<c042c670>] (gic_init_bases+0x170/0x2ec)
[<c042c500>] (gic_init_bases+0x0/0x2ec) from [<c042cdc8>] (gic_init_irq+0x8c/0xd8)
[<c042cd3c>] (gic_init_irq+0x0/0xd8) from [<c042827c>] (init_IRQ+0x1c/0x24)
[<c0428260>] (init_IRQ+0x0/0x24) from [<c04256c8>] (start_kernel+0x1a4/0x300)
[<c0425524>] (start_kernel+0x0/0x300) from [<70008070>] (0x70008070)
---[ end trace 1b75b31a2719ed1e ]---
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Punit Agrawal reports:
> I was trying to boot 3.8-rc5 on Realview EB 11MPCore using
> realview-smp_defconfig as a starting point but the kernel failed to
> progress past the log below (config attached).
>
> Pawel suggested I try reverting 384a2902 - "ARM: gic: use a private
> mapping for CPU target interfaces" that you've authored. With this
> commit reverted the kernel boots.
>
> I am not quite sure why the commit breaks 11MPCore but Pawel (cc'd)
> might be able to shed light on that.

Some early GIC implementations return zero for the first distributor
CPU routing register.  This means we can't rely on that telling us
which CPU interface we're connected to.  We know that these platforms
implement PPIs for IRQs 29-31 - but we shouldn't assume that these
will always be populated.

So, instead, scan for a non-zero CPU routing register in the first
32 IRQs and use that as our CPU mask.
Reported-by: NPunit Agrawal <punit.agrawal@arm.com>
Reviewed-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Pull drm regression fix from Dave Airlie:
 "This one fixes a sleep while locked regression that was introduced
  earlier in 3.8."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/ttm: fix fence locking in ttm_buffer_object_transfer, 2nd try