In interrupt.h these functions are declared only if
CONFIG_GENERIC_HARDIRQS is set.  We should define them under identical
conditions.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

gcc 3.4.6 doesn't like MODULE_DEVICE_TABLE(dmi, x) expansion enough to
error out.  Shut it up in a most simple way.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'hibern_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  SATA PIIX: Blacklist system that spins off disks during ACPI power off
  SATA Sil: Blacklist system that spins off disks during ACPI power off
  SATA AHCI: Blacklist system that spins off disks during ACPI power off
  SATA: Blacklisting of systems that spin off disks during ACPI power off
  DMI: Introduce dmi_first_match to make the interface more flexible
  Hibernation: Introduce system_entering_hibernation

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  pata-rb532-cf: remove set_irq_type from finish_io
  [libata] pata_via: support VX855, future chips whose IDE controller use 0x0571
  sata_mv: no longer experimental (v2)
  sata_mv: msi masking fix (v2)
  sata_mv: Properly initialize main irq mask
  sata_mv: remove bogus nsect restriction
  sata_mv: don't read hc_irq_cause
  sata_mv: fix 8-port timeouts on 508x/6081 chips
  sata_nv: fix MCP5x reset
  sata_nv: rename nv_nf2_hardreset()
  libata: set NODEV_HINT for 0x7f status
  libata-sff: fix incorrect EH message

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: ccm - Fix handling of null assoc data
  crypto: blkcipher - Fix WARN_ON handling in walk_done
  crypto: authenc - Fix zero-length IV crash

This Patch add the device information for the
MIC-3620 8-port RS-232 cPCI card from Advantech Co. Ltd.
Signed-off-by: NMichael Bramer <grisu@deb-support.de>
Signed-off-by: NAlan Cox <number6@the-village.bc.nu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The function jsm_remove_one is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NAlan Cox <number6@the-village.bc.nu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enabled serial UART driver for PNX833X devices.
Signed-off-by: NIhar Hrachyshka <ihar.hrachyshka@gmail.com>
Signed-off-by: NAlan Cox <number6@the-village.bc.nu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__tty_open could return (to userspace) holding the tty_mutex thanks to a
regression introduced by 4a2b5fdd ("Move
tty lookup/reopen to caller").

This was found by bisecting an fsfuzzer problem.  Admittedly I have no
idea how it managed to tickle this 100% reliably, but it is clearly a
regression and when hit leaves the box in a completely unusable state.
This patch lets the fsfuzzer test complete every time.
Signed-off-by: NEric Paris <eparis@redhat.com>
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.

To prevent this from happening we can blacklist the affected systems
using DMI information.

Blacklist HP 2510p that uses the ata_piix driver.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.

To prevent this from happening we can blacklist the affected systems
using DMI information.

Blacklist HP nx6325 that uses the sata_sil driver.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.

To prevent this from happening we can blacklist the affected systems
using DMI information.

Blacklist HP nx6310 that uses the AHCI driver.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Introduce new libata flags ATA_FLAG_NO_POWEROFF_SPINDOWN and
ATA_FLAG_NO_HIBERNATE_SPINDOWN that, if set, will prevent disks from
being spun off during system power off and hibernation, respectively
(to handle the hibernation case we need the new system state
SYSTEM_HIBERNATE_ENTER that can be checked against by libata, in
analogy with SYSTEM_POWER_OFF).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.

To prevent this from happening we can blacklist the affected systems
using DMI information.  However, only the on-board controlles should
be blacklisted and their PCI slot numbers can be used for this
purpose.  Unfortunately the existing interface for checking DMI
information of the system is not very convenient for this purpose,
because to use it, we would have to define special callback functions
or create a separate struct dmi_system_id table for each blacklisted
system.

To overcome this difficulty introduce a new function
dmi_first_match() returning a pointer to the first entry in an array
of struct dmi_system_id elements that matches the system DMI
information.  Then, we can use this pointer to access the entry's
.driver_data field containing the additional information, such as
the PCI slot number, allowing us to do the desired blacklisting.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Introduce boolean function system_entering_hibernation() returning
'true' during the last phase of hibernation, in which devices are
being put into low power states and the sleep state (for example,
ACPI S4) is finally entered.

Some device drivers need such a function to check if the system is
in the final phase of hibernation.  In particular, some SATA drivers
are going to use it for blacklisting systems in which the disks
should not be spun down during the last phase of hibernation (the
BIOS will do that anyway).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The driver has been tested without the call to set_irq_type at this
point and occurs to work fine, so it should be safe to remove it.
Signed-off-by: NPhil Sutter <n0-1@freewrt.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Its a valid use case to have null associated data in a ccm vector, but
this case isn't being handled properly right now.

The following ccm decryption/verification test vector, using the
rfc4309 implementation regularly triggers a panic, as will any
other vector with null assoc data:

* key: ab2f8a74b71cd2b1ff802e487d82f8b9
* iv: c6fb7d800d13abd8a6b2d8
* Associated Data: [NULL]
* Tag Length: 8
* input: d5e8939fc7892e2b

The resulting panic looks like so:

Unable to handle kernel paging request at ffff810064ddaec0 RIP: 
 [<ffffffff8864c4d7>] :ccm:get_data_to_compute+0x1a6/0x1d6
PGD 8063 PUD 0 
Oops: 0002 [1] SMP 
last sysfs file: /module/libata/version
CPU 0
Modules linked in: crypto_tester_kmod(U) seqiv krng ansi_cprng chainiv rng ctr aes_generic aes_x86_64 ccm cryptomgr testmgr_cipher testmgr aead crypto_blkcipher crypto_a
lgapi des ipv6 xfrm_nalgo crypto_api autofs4 hidp l2cap bluetooth nfs lockd fscache nfs_acl sunrpc ip_conntrack_netbios_ns ipt_REJECT xt_state ip_conntrack nfnetlink xt_
tcpudp iptable_filter ip_tables x_tables dm_mirror dm_log dm_multipath scsi_dh dm_mod video hwmon backlight sbs i2c_ec button battery asus_acpi acpi_memhotplug ac lp sg 
snd_intel8x0 snd_ac97_codec ac97_bus snd_seq_dummy snd_seq_oss joydev snd_seq_midi_event snd_seq snd_seq_device snd_pcm_oss snd_mixer_oss ide_cd snd_pcm floppy parport_p
c shpchp e752x_edac snd_timer e1000 i2c_i801 edac_mc snd soundcore snd_page_alloc i2c_core cdrom parport serio_raw pcspkr ata_piix libata sd_mod scsi_mod ext3 jbd uhci_h
cd ohci_hcd ehci_hcd
Pid: 12844, comm: crypto-tester Tainted: G      2.6.18-128.el5.fips1 #1
RIP: 0010:[<ffffffff8864c4d7>]  [<ffffffff8864c4d7>] :ccm:get_data_to_compute+0x1a6/0x1d6
RSP: 0018:ffff8100134434e8  EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8100104898b0 RCX: ffffffffab6aea10
RDX: 0000000000000010 RSI: ffff8100104898c0 RDI: ffff810064ddaec0
RBP: 0000000000000000 R08: ffff8100104898b0 R09: 0000000000000000
R10: ffff8100103bac84 R11: ffff8100104898b0 R12: ffff810010489858
R13: ffff8100104898b0 R14: ffff8100103bac00 R15: 0000000000000000
FS:  00002ab881adfd30(0000) GS:ffffffff803ac000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff810064ddaec0 CR3: 0000000012a88000 CR4: 00000000000006e0
Process crypto-tester (pid: 12844, threadinfo ffff810013442000, task ffff81003d165860)
Stack:  ffff8100103bac00 ffff8100104898e8 ffff8100134436f8 ffffffff00000000
 0000000000000000 ffff8100104898b0 0000000000000000 ffff810010489858
 0000000000000000 ffff8100103bac00 ffff8100134436f8 ffffffff8864c634
Call Trace:
 [<ffffffff8864c634>] :ccm:crypto_ccm_auth+0x12d/0x140
 [<ffffffff8864cf73>] :ccm:crypto_ccm_decrypt+0x161/0x23a
 [<ffffffff88633643>] :crypto_tester_kmod:cavs_test_rfc4309_ccm+0x4a5/0x559
[...]

The above is from a RHEL5-based kernel, but upstream is susceptible too.

The fix is trivial: in crypto/ccm.c:crypto_ccm_auth(), pctx->ilen contains
whatever was in memory when pctx was allocated if assoclen is 0. The tested
fix is to simply add an else clause setting pctx->ilen to 0 for the
assoclen == 0 case, so that get_data_to_compute() doesn't try doing
things its not supposed to.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

When we get left-over bits from a slow walk, it means that the
underlying cipher has gone troppo.  However, as we're handling
that case we should ensure that the caller terminates the walk.

This patch does this by setting walk->nbytes to zero.
Reported-by: NRoel Kluin <roel.kluin@gmail.com>
Reported-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Introduced by 8adb711f ("debugfs:
introduce stub for debugfs_create_size_t() when DEBUG_FS=n") and due to
a simple missing "static inline".
Reported-and-tested-by: NJeff Chua <jeff.chua.linux@gmail.com>
Acked-by: NGreg KH <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/home/rmk/linux-2.6-arm: (22 commits)
  [ARM] fix section-based ioremap
  [NET] am79c961a: fix spin_lock usage
  [ARM] omap: usb: thou shalt not provide empty release functions
  [ARM] omap: watchdog: allow OMAP watchdog driver on OMAP34xx platforms
  [ARM] 5369/1: omap mmc: Add new omap hsmmc controller for 2430 and 34xx, v3
  [ARM] clkdev: fix clock matching
  [ARM] 5370/1: at91: fix rm9200 watchdog
  [ARM] 5368/1: arch/arm/mach-davinci/usb.c buildfix
  [ARM] 5365/1: s3cmci: Use new include path of dma.h
  [ARM] fix StrongARM-11x0 page copy implementation
  [ARM] omap: ensure OMAP drivers pass a struct device to clk_get()
  ARM: OMAP: Fix compile for h3 MMC
  ARM: OMAP: Remove unused platform devices, v3
  ARM: OMAP: Fix ASoC by enabling writes to XCCR and RCCR McBSP registers, v3
  ARM: OMAP: Fix OSK ASoC by registering I2C board info for tlvaic23
  ARM: OMAP: remove duplicated #include's
  ARM: OMAP: Fix DMA CCR programming for request line > 63, v3
  ARM: OMAP: Fix gpio.c compile on 15xx with CONFIG_DEBUGFS
  ARM: OMAP: Fix compile for beagle
  ARM: OMAP: Fix gpio by switching to generic gpio calls, v2
  ...

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c: Warn on deprecated binding model use
  eeprom: More consistent symbol names
  eeprom: Move 93cx6 eeprom driver to /drivers/misc/eeprom
  spi: Move at25 (for SPI eeproms) to /drivers/misc/eeprom
  i2c: Move old eeprom driver to /drivers/misc/eeprom
  i2c: Move at24 to drivers/misc/eeprom
  i2c: Quilt tree has moved
  i2c: Delete many unused adapter IDs
  i2c: Delete 10 unused driver IDs

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
  kbuild: fix kbuild.txt typos
  kbuild: print usage with no arguments in scripts/config
  Revert "kbuild: strip generated symbols from *.ko"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (92 commits)
  gianfar: Revive VLAN support
  vlan: Export symbols as non GPL symbols.
  bnx2x: tx_has_work should not wait for FW
  netxen: reduce memory footprint
  netxen: fix vlan tso/checksum offload
  net: Fix linux/if_frad.h's suitability for userspace.
  net: Move config NET_NS to from net/Kconfig to init/Kconfig
  isdn: Fix missing ifdef in isdn_ppp
  networking: document "nc" in addition to "netcat" in netconsole.txt
  e1000e: workaround hw errata
  af_key: initialize xfrm encap_oa
  virtio_net: Fix MAX_PACKET_LEN to support 802.1Q VLANs
  lcs: fix compilation for !CONFIG_IP_MULTICAST
  rtl8187: Add termination packet to prevent stall
  iwlwifi: fix rs_get_rate WARN_ON()
  p54usb: fix packet loss with first generation devices
  sctp: Fix another socket race during accept/peeloff
  sctp: Properly timestamp outgoing data chunks for rtx purposes
  sctp: Correctly start rtx timer on new packet transmissions.
  sctp: Fix crc32c calculations on big-endian arhes.
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix DAX handling via userspace access from kernel.
  sparc64: Annotate sparc64 specific syscalls with SYSCALL_DEFINEx()
  [CVE-2009-0029] sparc: Enable syscall wrappers for 64-bit
  sparc64: Initialize FHC/CLOCK LED platform_device 'id' field correctly.
  sparc64: fix modpost failure
  sparc64: fix readout of cpu/fpu type

commit 77ecaf2d ("gianfar: Fix VLAN
HW feature related frame/buffer size calculation") wrongly removed
priv->vlgrp assignment, and now priv->vlgrp is always NULL.

This patch fixes the issue, plus fixes following sparse warning
introduced by the same commit:
gianfar.c:1406:13: warning: context imbalance in 'gfar_vlan_rx_register' - wrong count at exit

gfar_vlan_rx_register() checks for "if (old_grp == grp)" and tries
to return w/o dropping the lock.

According to net/8021q/vlan.c VLAN core issues rx_register() callback:
1. In register_vlan_dev() only on a newly created group;
2. In unregister_vlan_dev() only if the group becomes empty.

Thus the check in the gianfar driver isn't needed.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In previous kernels, any kernel module could get access to the
'real-device' and the VLAN-ID for a particular VLAN.  In more recent
kernels, the code was restructured such that this is hard to do
without accessing private .h files for any module that cannot use
GPL-only symbols.

Attached is a patch to once again allow non-GPL modules the ability to
access the real-device and VLAN id for VLANs.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current tx_has_work waited until all packets sent by the driver
are marked as completed by the FW. This is too greedy and it causes
the bnx2x_poll to spin in vain. The driver should only check that all
packets FW already completed are freed - only in unload flow the
driver should make sure that transmit queue is empty
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o reduce rx ring size from 8192 to 4096.
o cut down old huge lro buffers.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o set netdev->vlan_features appropriately.
o fix tso descriptor initialization for vlan case.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The userspace interfaces are protected by CONFIG_* ifdefs
and that of course can't work.

Reported by Jaswinder Singh Rajput.
Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make NET_NS available underneath the generic Namespaces config option
since all of the other namespace options are there.
Signed-off-by: NMatt Helsley <matthltc@us.ibm.com>
Acked-by: NSerge Hallyn <serue@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following patch fixes a warning caused by a missing ifdef in
isdn_ppp.c. A function was defined, but never used if CONFIG_IPPP_FILTER
was not defined.

The warning was: 'get_filter' defined but not used
Patch is against 2.6.28.1
Signed-off-by: NDaniele Venzano <venza@brownhat.org>
Acked-by: NKarsten Keil <kkeil@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let the kernel developers know that i2c_attach_client() and
i2c_detach_client() are deprecated and should no longer be used.
Drivers using these should be converted to the standard device
driver binding model (probe and remove methods.)
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NBen Dooks <ben-linux@fluff.org>

Now that all EEPROM drivers live in the same place, let's harmonize
their symbol names.

Also fix eeprom's dependencies, it definitely needs sysfs, and is no
longer experimental after many years in the kernel tree.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Update Kconfig text to specify this driver as I2C.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

As drivers/i2c/chips is going to go away, move the driver to
drivers/misc/eeprom. Other eeprom drivers may be moved here later, too.
Update Kconfig text to specify this driver as I2C.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

My i2c quilt tree will now be hosted on kernel.org, because I can
conveniently use rsync there.

Also list the new i2c wiki.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NJean Delvare <khali@linux-fr.org>