Add support for RTC controller found on Alphascale asm9260
SoC.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

DS3231 has programmable square-wave output signal.
This enables to use this feature as a clock provider of
common clock framework.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: NMichael Turquette <mturquette@baylibre.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

To make RTC block of MAX77686/MAX77802 as independent driver,
move the registration of i2c device, regmap for register access
and irq_chip for interrupt support inside the RTC driver.
Removed the same initialisation from MFD driver.

Having this change will allow to reuse this driver for different
PMIC/devices from Maxim Semiconductor if they kept same RTC IP on
different PMIC. Some of examples as PMIC MAX77620, MAX20024 where
same RTC IP used and hence driver for these chips will use this
driver only for RTC support.
Suggested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Tested-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

There is different RTC I2C address for RTC block in MAX77686.
Driver is creating dummy i2c client for this address to access
the register of this IP block.

As there is no call to i2c_get_clientdata() for rtc_i2c client,
there is no need to store pointer and hence removing the call
to set client data for rtc i2c client.
Suggested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Get rid of referring parent device info for register access
all the places by making regmap as part of max77686 rtc
device info. This will also remove the need of storing parent
device info in max77686 rtc device info as this is no more required.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

rtc_regmap should be used to access all RTC registers instead
of parent regmap regardless of what chip or property have it.

This makes the register access uniform and extendible for other
chips.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Fix following check patch error in rtc-max77686 driver:
- Alignment should match open parenthesis.
- braces {} should be used on all arms of this statement.
- Prefer using the BIT macro
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

At the moment the "sun6i" RTC drivers depends on having two specific
SoC families selected.
The Allwinner A64 SoC has the same RTC, so extend the Kconfig option
to allow inclusion of the driver for all Allwinner SoCs.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The RX6110 comes in two different variants: SPI and I2C.
This driver only supports the SPI variant.

If the need ever arises to also support the I2C variant, this driver
could easily be refactored to support both cases.
Reviewed-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add the binding documentation for the Epson RX6110 RTC.
Acked-by: NRob Herring <robh@kernel.org>
Reviewed-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

pcf2123 data sheet recommends a software reset when the chip
is first powered on. This change avoids resetting the chip
every time the driver is loaded, which has some negative effects.

There are several registers including a clock rate adjustment that really
should survive a reload of the driver (or reboot).

In addition, stopping and restarting the clock to verify the chip is
there is not a good thing once the time is set.

According to the data sheet, the seconds register has a 1 in
the high bit when the voltage has gotten low. We check for this
condition, as well as whether the time retrieved from the chip is
valid. We reset the rtc only if the time is not reliable and valid.
This is sufficient for checking for the presence of the chip,
as either all zeros or all 0xff will result in an invalid time/date
Signed-off-by: NJoshua Clayton <stillcompiling@gmail.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Refactor chip reset items into its own function, isolating it from
the rest of the device probe.
Subsequent commits will avoid calling this code.
Signed-off-by: NJoshua Clayton <stillcompiling@gmail.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add new functions pcf2123_write(), and pcf2123_write_reg().
Use named defines for the values being written.

This improves modularity and readability, and reduces lines of code.
Signed-off-by: NJoshua Clayton <stillcompiling@gmail.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Put read operations into a function.
This improves modularity and readability.
Signed-off-by: NJoshua Clayton <stillcompiling@gmail.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add defines for all 16 registers in the pcf2123.
Add defines for useful bits from several registers
I've tried to document all the registers, and
as best as possible, all the special bits they employ

Use BIT() wherever possible in the bit definitions
Signed-off-by: NJoshua Clayton <stillcompiling@gmail.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

DS3231 has the temperature registers with a resolution of 0.25
degree celsius.  This enables to get the value through hwmon.

	# cat /sys/class/i2c-adapter/i2c-2/2-0068/hwmon/hwmon0/temp1_input
	21000
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

For RTC chips with no IRQ directly connected to the SoC, the RTC chip
can be forced as a wakeup source by stating that explicitly in
the device's .dts file using the "wakeup-source" boolean property.
This will guarantee the 'wakealarm' sysfs entry is available on the
device, if supported by the RTC.

With these changes to the driver rtc-ds1307 and the necessary entries
in the .dts file, I get an working ds1337 RTC on the Witty Pi extension
board by UUGear for the Raspberry Pi.

An example for the entry in the .dts file:

	rtc: ds1337@68 {
		compatible = "dallas,ds1337";
		reg = <0x68>;
		wakeup-source;

If the "wakeup-source" property is set, do not request an IRQ.
Set also UIE mode to unsupported, to get a working 'hwclock' binary.
Signed-off-by: NMichael Lange <linuxstuff@milaw.biz>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The mt6397 RTC driver can be built either when the MFD_MT6397 driver
is enabled (which selects IRQ_DOMAIN), or when compile testing.
The latter however fails without IRQ domains:

drivers/rtc/rtc-mt6397.c: In function 'mtk_rtc_probe':
drivers/rtc/rtc-mt6397.c:326:13: error: implicit declaration of function 'irq_create_mapping' [-Werror=implicit-function-declaration]
  rtc->irq = irq_create_mapping(mt6397_chip->irq_domain, res->start);

This adds an explicit dependency for the COMPILE_TEST case.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NEddie Huang <eddie.huang@mediatek.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The rv8803 has its own driver that should be used. Remove its id from
the rx8025 driver.

Fixes: b1f9d790Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

For better readability, use to_spi_device() and kobj_to_dev() instead
of container_of().
Signed-off-by: NGeliang Tang <geliangtang@163.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Cleanup of entire driver of its dmesg output:
1. Remove printing of the function name, because printing device name is
   sufficient. This also makes the dev_err()-like functions more compact
   and readable (not need of line break).
2. Lower from info to debug printing of each RTC interrupt (no need to
   make noise on each alarm).
3. Remove dev_info() at beginning of probe because a message is already
   always printed by either probe failure or from registering the RTC
   device as /dev/rtcX.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The max77686 RTC driver now supports the max77802 RTC as
well so there's no need to have a separate driver anymore.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: NAndi Shyti <andi.shyti@samsung.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The regmap_irq_get_virq() can return 0 or -EINVAL in error conditions
but driver checked only for value of 0.

This could lead to a cast of -EINVAL to an unsigned int used as a
interrupt number for devm_request_threaded_irq(). Although this is not
yet fatal (devm_request_threaded_irq() will just fail with -EINVAL) but
might be a misleading when diagnosing errors.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 6f1c1e71 ("mfd: max77686: Convert to use regmap_irq")
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The max77686 RTC only supports a range of 99 years so instead of using
year 1900 as the base, the year 2000 is used. This means that 1900 to
1999 are unsupported years.

The driver was printing a warning for those values but was returning a
error so for consistency, print an error message instead and don't say
that a year 2000 is assumed, since the year is not set.

Also, it is better to use dev_* log functions instead of pr_* to print
information about the device in the kernel log in a standardized way.

This also allows to remove the local pr_fmt() defined macro.
Suggested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NAndi Shyti <andi.shyti@samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The MAX77686 and MAX77802 RTC IP blocks are very similar with only
these differences:

0) The RTC registers layout and addresses are different.

1) The MAX77686 use 1 bit of the sec/min/hour/etc registers as the
   alarm enable while MAX77802 has a separate register for that.

2) The MAX77686 RTCYEAR register valid values range is 0..99 while
   for MAX77802 is 0..199.

3) The MAX77686 has a separate I2C address for the RTC registers
   while the MAX77802 uses the same I2C address as the PMIC regs.

5) The minimum delay before a RTC update (16 msecs vs 200 usecs).

There are separate drivers for MAX77686 and MAX77802 RTC IP blocks
but the differences are not that big so the driver can be extended
to support both instead of duplicating a lot of code in 2 drivers.
Suggested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NAndi Shyti <andi.shyti@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The max77686 driver is generic enough that can be used for other
Maxim RTC IP blocks but these might not have the same registers
layout so instead of accessing the registers directly, add a map
to translate offsets to the real registers addresses for each IP.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NAndi Shyti <andi.shyti@samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The driver has some hard-coded values such as the minimum delay needed
before a RTC update or the mask used for the sec/min/hour/etc registers.

Use a data structure that contains these values and pass as driver data
using the platform device ID table for each device.

This allows to make the driver's ops callbacks more generic so other RTC
that are similar but don't have the same values can also be supported.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: NAndi Shyti <andi.shyti@samsung.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Documentation/timers/timers-howto.txt suggest to use usleep_range()
instead of msleep() for small msec (1ms - 20ms) since msleep() will
often sleep for 20ms for any value in that range.

This is fine in this case since 16ms is the _minimum_ delay required
by max77686 for an RTC update but by using usleep_range() instead of
msleep(), the driver can support other RTC IP blocks with a shorter
minimum delay (i.e: in the range of usecs instead of msecs).
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NAndi Shyti <andi.shyti@samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

It is better to use the ARRAY_SIZE() macro instead of the array length
to avoid bugs if the array is later changed and the length not updated.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NAndi Shyti <andi.shyti@samsung.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The function is always returning zero even in case of failures since
the ret value was not propagated to the callers. Fix the error path.
Reported-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: NAndi Shyti <andi.shyti@samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.

  The executive summary:

   - ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
   - Avoid useless rebuilds for zboot.
   - jz4780: Add NEMC, BCH and NAND device tree nodes
   - Initial support for the MicroChip's DT platform.  As all the device
     drivers are missing this is still of limited use.
   - Some Loongson3 cleanups.
   - The unavoidable whitespace polishing.
   - Reduce clock skew when synchronizing the CPU cycle counters on CPU
     startup.
   - Add MIPS R6 fixes.
   - Lots of cleanups across arch/mips as fallout from KVM.
   - Lots of minor fixes and changes for IEEE 754-2008 support to the
     FPU emulator / fp-assist software.
   - Minor Ralink, BCM47xx and bcm963xx platform support improvments.
   - Support SMP on BCM63168"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
  MIPS: zboot: Add support for serial debug using the PROM
  MIPS: zboot: Avoid useless rebuilds
  MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
  MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
  MIPS: bcm963xx: Update bcm_tag field image_sequence
  MIPS: bcm963xx: Move extended flash address to bcm_tag header file
  MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
  MIPS: bcm63xx: nvram: Use nvram structure definition from header file
  MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
  MAINTAINERS: Add KVM for MIPS entry
  MIPS: KVM: Add missing newline to kvm_err()
  MIPS: Move KVM specific opcodes into asm/inst.h
  MIPS: KVM: Use cacheops.h definitions
  MIPS: Break down cacheops.h definitions
  MIPS: Use EXCCODE_ constants with set_except_vector()
  MIPS: Update trap codes
  MIPS: Move Cause.ExcCode trap codes to mipsregs.h
  MIPS: KVM: Make kvm_mips_{init,exit}() static
  MIPS: KVM: Refactor added offsetof()s
  MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
  ...

Merge tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull x86 platform driver updates from Darren Hart:
 "Emergency travel prevented me from completing my final testing on this
  until today.  Nothing here that couldn't wait until RC1 fixes, but I
  thought it best to get it out sooner rather than later as it does
  contain a build warning fix.

  Summary:

  A build warning fix, MAINTAINERS cleanup, and a new DMI quirk:

  ideapad-laptop:
   - Add Lenovo Yoga 700 to no_hw_rfkill dmi list

  MAINTAINERS:
   - Combine multiple telemetry entries

  intel_telemetry_debugfs:
   - Fix unused warnings in telemetry debugfs"

* tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
  MAINTAINERS: Combine multiple telemetry entries
  intel_telemetry_debugfs: Fix unused warnings in telemetry debugfs

Pull thermal management updates from Zhang Rui:
 "The top merge commit was re-generated yesterday because two topic
  branches were dropped from this pull request in the last minute due to
  some unaddressed comments.  All the other material has been in
  linux-next for quite a while.

  Specifics:

   - Enhance thermal core to handle unexpected device cooling states
     after fresh boot and system resume.  From Zhang Rui and Chen Yu.

   - Several fixes and cleanups on Rockchip and RCAR thermal drivers.
     From Caesar Wang and Kuninori Morimoto.

   - Add Broxton support for Intel processor thermal reporting device
     driver.  From Amy Wiles"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: trip_point_temp_store() calls thermal_zone_device_update()
  thermal: rcar: rcar_thermal_get_temp() return error if strange temp
  thermal: rcar: check irq possibility in rcar_thermal_irq_xxx()
  thermal: rcar: check every rcar_thermal_update_temp() return value
  thermal: rcar: move rcar_thermal_dt_ids to upside
  thermal: rockchip: Support the RK3399 SoCs in thermal driver
  thermal: rockchip: Support the RK3228 SoCs in thermal driver
  dt-bindings: rockchip-thermal: Support the RK3228/RK3399 SoCs compatible
  thermal: rockchip: fix a trivial typo
  Thermal: Enable Broxton SoC thermal reporting device
  thermal: constify pch_dev_ops structure
  Thermal: do thermal zone update after a cooling device registered
  Thermal: handle thermal zone device properly during system sleep
  Thermal: initialize thermal zone device correctly

Pull 9p updates from Eric Van Hensbergen:
 "Sorry for the last minute pull request, there's was a change that
  didn't get pulled into for-next until two weeks ago and I wanted to
  give it some bake time.

  Summary:

  Rework and error handling fixes, primarily in the fscatch and fd
  transports"

* tag 'for-linus-4.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  fs/9p: use fscache mutex rather than spinlock
  9p: trans_fd, bail out if recv fcall if missing
  9p: trans_fd, read rework to use p9_parse_header
  net/9p: Add device name details on error

Pull Ceph updates from Sage Weil:
 "The two main changes are aio support in CephFS, and a series that
  fixes several issues in the authentication key timeout/renewal code.

  On top of that are a variety of cleanups and minor bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: remove outdated comment
  libceph: kill off ceph_x_ticket_handler::validity
  libceph: invalidate AUTH in addition to a service ticket
  libceph: fix authorizer invalidation, take 2
  libceph: clear messenger auth_retry flag if we fault
  libceph: fix ceph_msg_revoke()
  libceph: use list_for_each_entry_safe
  ceph: use i_size_{read,write} to get/set i_size
  ceph: re-send AIO write request when getting -EOLDSNAP error
  ceph: Asynchronous IO support
  ceph: Avoid to propagate the invalid page point
  ceph: fix double page_unlock() in page_mkwrite()
  rbd: delete an unnecessary check before rbd_dev_destroy()
  libceph: use list_next_entry instead of list_entry_next
  ceph: ceph_frag_contains_value can be boolean
  ceph: remove unused functions in ceph_frag.h

Pull SMB3 fixes from Steve French:
 "A collection of CIFS/SMB3 fixes.

  It includes a couple bug fixes, a few for improved debugging of
  cifs.ko and some improvements to the way cifs does key generation.

  I do have some additional bug fixes I expect in the next week or two
  (to address a problem found by xfstest, and some fixes for SMB3.11
  dialect, and a couple patches that just came in yesterday that I am
  reviewing)"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cifs_dbg() outputs an uninitialized buffer in cifs_readdir()
  cifs: fix race between call_async() and reconnect()
  Prepare for encryption support (first part). Add decryption and encryption key generation. Thanks to Metze for helping with this.
  cifs: Allow using O_DIRECT with cache=loose
  cifs: Make echo interval tunable
  cifs: Check uniqueid for SMB2+ and return -ESTALE if necessary
  Print IP address of unresponsive server
  cifs: Ratelimit kernel log messages

Like the Yoga 900 models the Lenovo Yoga 700 does not have a
hw rfkill switch, and trying to read the hw rfkill switch through the
ideapad module causes it to always reported blocking breaking wifi.

This commit adds the Lenovo Yoga 700 to the no_hw_rfkill dmi list, fixing
the wifi breakage.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1295272
Tested-by: <dinyar.rabady+spam@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJosh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

This patch combines all the telemetry file entries in MAINTAINERS via
wildcard.
Signed-off-by: NSouvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

This patch fixes compile time warnings when CONFIG_PM_SLEEP
is undefined. In this case sleep related counters are unused.
Signed-off-by: NSouvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>