This patch separates support for big endian MMIO register access
and big endian descriptors in order to support the Toshiba SCC
implementation which has big endian registers but little endian
in-memory descriptors.

It simplifies the access functions a bit in ohci.h while at it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch applies David Brownell's suggestion for reworking the
OHCI quirk mechanism via a table of PCI IDs. It adapts the existing
quirks to use that mechanism.

This also moves the quirks to reset() as suggested by the comment
in there. This is necessary as we need to have the endian properly
set before we try to init the controller.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is an OHCI cleanup patch ... it removes a lot of erroneous whitespace
(space before tab, at end of line) as well as the obsolete inline changelog.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We want to avoid legacy APIs like pci_find_slot().
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If some problem occurs during ehci startup, for instance, request_irq fails,
echi hcd driver tries it best to cleanup, but fails to unregister reboot
notifier, which in turn leads to crash on reboot/poweroff.

The following patch resolves this problem by not using reboot notifiers
anymore, but instead making ehci/ohci driver get its own shutdown method.  For
PCI, it is done through pci glue, for everything else through platform driver
glue.

One downside: sa1111 does not use platform driver stuff, and does not have its
own shutdown hook, so no 'shutdown' is called for it now.  I'm not sure if it
is really necessary on that platform, though.
Signed-off-by: NAleks Gorelov <dared1st@yahoo.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This teaches OHCI to use the root hub status change (RHSC) IRQ, bypassing
root hub timers most of the time and switching over to the "new" root hub
polling scheme.  It's complicated by the fact that implementations of OHCI
trigger and ack that IRQ differently (the spec is vague there).

Avoiding root hub timers helps mechanisms like "dynamic tick" leave the
CPU in lowpower modes for longer intervals.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This teaches several USB host controller drivers to treat PRETHAW as a chip
reset since the controller, and all devices connected to it, are no longer in
states compatible with how the snapshotted suspend() left them.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We could use the recently added PCI_CLASS_SERIAL_USB_UHCI,
PCI_CLASS_SERIAL_USB_OHCI and PCI_CLASS_SERIAL_USB_EHCI defines in
more places, for slightly shorter and clearer code.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This makes OHCI use the driver model wakeup control bits for its root hub
(e.g. disable on amd756, because of chip erratum) and for the controller
itself.  It no longer uses the hcd glue bits with those roles, and depends
on the previous patch making the root hub available earlier.

Note that on most platforms (boot code properly setting the RWC bit) this
gives a partial workaround for the way PCI isn't currently flagging devices
that support PME# signals.  (Because of odd PCI init sequencing on PPC.)
That's because many OHCI controllers support "legacy PCI PM" ... without
involving any PCI PM capability.

USB wakeup from STR, if it works on your system, may still involve
tweaking things by hand in /proc/acpi/wakeup.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch closes the IRQ race and makes various other OHCI & EHCI code
path safer vs. suspend/resume.
I've been able to (finally !) successfully suspend and resume various
Mac models, with or without USB mouse plugged, or plugging while asleep,
or unplugging while asleep etc... all without a crash.

Alan, please verify the UHCI bit I did, I only verified that it builds.
It's very simple so I wouldn't expect any issue there. If you aren't
confident, then just drop the hunks that change uhci-hcd.c

I also made the patch a little bit more "safer" by making sure the store
to the interrupt register that disables interrupts is not posted before
I set the flag and drop the spinlock.

Without this patch, you cannot reliably sleep/wakeup any recent Mac, and
I suspect PCs have some more sneaky issues too (they don't frankly crash
with machine checks because x86 tend to silently swallow PCI errors but
that won't last afaik, at least PCI Express will blow up in those
situations, but the USB code may still misbehave).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This should fix a suspend/resume issues that appear with OHCI on some
PPC hardware.  The PCI layer should doesn't have the hooks needed for
such ASIC-specific hooks (in this case, software clock gating), so
this moves the code to do that into hcd-pci.c ... where it can be
done after the relevant PCI PM state transition (to/from D3).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.

In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch.  This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other.  So if any
hunk rejects or gets in the way of other patches, just drop it.  My scripts
will pick it up again in the next round.
Signed-off-by: NTim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add .owner initialisation to the device drivers
in drivers/usb/host so that when built as module
the device_driver refers to the owning module
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as580) is perhaps the only result from the long discussion I
had with David about his changes to the root-hub suspend/resume code.  It
renames the hub_suspend and hub_resume methods in struct usb_hcd to
bus_suspend and bus_resume.  These are more descriptive names, since the
methods really do suspend or resume an entire USB bus, and less likely to
be confused with the hub_suspend and hub_resume routines in hub.c.

It also takes David's advice about removing the layer of bus glue, where
those methods are called.  And it implements a related change that David
made to the other HCDs but forgot to put into dummy_hcd.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This simplifies the OHCI root hub suspend logic:

 - Uses new usbcore root hub calls to make autosuspend work again:
	* Uses a newish usbcore root hub wakeup mechanism,
	  making requests to khubd not keventd.
	* Uses an even newer sibling suspend hook.

 - Expect someone always made usbcore call ohci_hub_suspend() before bus
   glue fires; and that ohci_hub_resume() is only called after that bus
   glue ran.  Previously, only CONFIG_USB_SUSPEND promised those things.
   (Includes updates to PCI and OMAP bus glue.)

 - Handle a not-noticed-before special case during resume from one of
   the swsusp snapshots when using "usb-handoff":  the controller isn't
   left in RESET state.  (A bug to fix in the usb-handoff code...)

Also cleans up a minor debug printk glitch, and switches an mdelay over
to an msleep (how did that stick around for so long?).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/host/ohci-dbg.c  |    4 ----
 drivers/usb/host/ohci-hcd.c  |    2 +-
 drivers/usb/host/ohci-hub.c  |   42 ++++++++++++------------------------------
 drivers/usb/host/ohci-mem.c  |    1 -
 drivers/usb/host/ohci-omap.c |   36 ++++++++++++------------------------
 drivers/usb/host/ohci-pci.c  |   40 ++++++++--------------------------------
 drivers/usb/host/ohci.h      |    1 -
 7 files changed, 33 insertions(+), 93 deletions(-)

This simplifies some of the PM-related #ifdeffing by recognizing
that USB_SUSPEND depends on PM.  Also, OHCI drivers were often
testing for USB_SUSPEND when they should have tested just PM.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/hcd.c          |    2 ++
 drivers/usb/host/ohci-hcd.c     |    2 +-
 drivers/usb/host/ohci-hub.c     |    4 ++--
 drivers/usb/host/ohci-omap.c    |    2 +-
 drivers/usb/host/ohci-pci.c     |    2 +-
 drivers/usb/host/ohci-ppc-soc.c |    4 ++--
 drivers/usb/host/ohci-pxa27x.c  |    2 +-
 drivers/usb/host/ohci-s3c2410.c |    3 +--
 drivers/usb/host/ohci-sa1111.c  |    2 +-
 9 files changed, 12 insertions(+), 11 deletions(-)

This patch removes the extra usb_suspend_device() parameter.  The original
reason to pass that parameter was so that this routine could suspend any
active children.  A previous patch removed that functionality ... leaving
no reason to pass the parameter.  A close analogy is pci_set_power_state,
which doesn't need a pm_message_t either.

On the internal code path that comes through the driver model, the parameter
is now used to distinguish cases where USB devices need to "freeze" but not
suspend.   It also checks for an error case that's accessible through sysfs:
attempting to suspend a device before its interfaces (or for hubs, ports).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/hub.c         |   34 +++++++++++++++++++++-------------
 drivers/usb/core/usb.c         |   23 +++++++++++++++++++++--
 drivers/usb/host/ehci-hcd.c    |    2 +-
 drivers/usb/host/isp116x-hcd.c |    2 +-
 drivers/usb/host/ohci-pci.c    |    2 +-
 include/linux/usb.h            |    2 +-
 6 files changed, 46 insertions(+), 19 deletions(-)

This patch removes CONFIG_PMAC_PBOOK (PowerBook support).  This is now
split into CONFIG_PMAC_MEDIABAY for the actual hotswap bay that some
powerbooks have, CONFIG_PM for power management related code, and just left
out of any CONFIG_* option for some generally useful stuff that can be used
on non-laptops as well.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This adds a quirk to the OHCI driver that lets it work with an old
Compaq implementation.  It also removes some needless strings from
the non-debug version of the driver.
Signed-off-by: NChris Clayton <chris_clayton@f1internet.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch includes minor "sparse -Wbitwise" updates for the PCI based
HCDs.  Almost all of them involve just changing the second parameter of the
suspend() method to a pm_message_t ...  the others relate to how the EHCI
code walks in-memory data structures.  (There's a minor bug fixed there too
...  affecting the big-endian sysfs async schedule dump.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>


Index: gregkh-2.6/drivers/usb/core/hcd.h
===================================================================

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!