- 21 5月, 2010 1 次提交
-
-
由 Mallikarjuna R Chilakala 提交于
This adds support for a new copper device for 82599, device id 0x151c. This 82599 10GBase-T device uses the PHY's internal temperature sensor to guard against over-temp conditions. In this scenario the PHY will be put in a low power mode and link will no longer be able to transmit or receive any data. When this occurs, the over-temp interrupt is latched and driver logs this error message. A HW reset or power cycle is required to clear this status. Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 06 5月, 2010 1 次提交
-
-
由 Greg Rose 提交于
Add support for the "ip link set" and "ip link show" commands that allow configuration of the virtual functions' MAC and port VLAN via user space command line. Signed-off-by: NGreg Rose <gregory.v.rose@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 5月, 2010 1 次提交
-
-
由 David S. Miller 提交于
This reverts commit d5ffd75a. As requested by Jeff Kircher. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 28 4月, 2010 1 次提交
-
-
由 Nicholas Nunley 提交于
Due to an errata in 82598 parts MSI-X needs to be disabled in certain ixgbe devices designed to transfer peer-to-peer traffic on the PCIe bus. This patch sets the default interrupt type to MSI rather than MSI-X for specific Cisco ixgbe adapters. Signed-off-by: NNicholas Nunley <nicholasx.d.nunley@intel.com> Acked-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 3月, 2010 1 次提交
-
-
由 John Fastabend 提交于
In the last patch I missed an unecessary min_t comparison. This patch removes it, the path allocates at most 72 tx queues for 82599 and 24 for 82598 there is no need for this check. Additionally this sets MAX_[TX|RX]_QUEUES to 72. Which is used as the size for the tx/rx_ring arrays. There is no reason to have more tx_rings/rx_rings then num_tx_queues. Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 11 2月, 2010 1 次提交
-
-
由 Peter Waskiewicz 提交于
This patch adds n-tuple filter programming to 82599. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 2月, 2010 3 次提交
-
-
由 PJ Waskiewicz 提交于
This patch allocates the ring structures themselves on each NUMA node along with the buffer_info structures. This way we don't allocate the entire ring memory on a single node in one big block, thus reducing NUMA node memory crosstalk. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jesse Brandeburg 提交于
The default policy for the current driver is to do all its memory allocation on whatever processor is running insmod/modprobe. This is less than optimal. This driver's default mode of operation will be to use each node for each subsequent transmit/receive queue. The most efficient allocation will be to then have the interrupts bound in such a way as to match up the interrupt of the queue to the cpu where its memory was allocated. Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John Fastabend 提交于
Processing multiple ixgbe_watchdog_task calls may cause the link_up variable and IXGBE_FLAG_NEED_LINK_UPDATE flag to be set incorrectly. In the worse case this is causing the netif_carrier_off to be called inappropriately which results in an interface that can't be brought up. Although schedule_work() will only schedule the task if it is not already on the work queue the WORK_STRUCT_PENDING bits are cleared just before calling the work function. This allows WORK_STRUCT_PENDING to be cleared, the work function to start and meanwhile schedule another task. This patch adds a mutex to the watchdog task. This bug is actualized by changing DCB settings or doing extended cable pull or reset tests. Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 1月, 2010 1 次提交
-
-
由 Greg Rose 提交于
This data storage for SW emulated MAC addresses is unlikely to ever be used so pull it. Signed-off-by: NGreg Rose <gregory.v.rose@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 1月, 2010 1 次提交
-
-
由 Shannon Nelson 提交于
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 11 1月, 2010 1 次提交
-
-
由 Greg Rose 提交于
This patch adds register definitions, bit definitions and structures used by the driver to support SR-IOV features of the 82599 controller. Signed-off-by: NGreg Rose <gregory.v.rose@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 12月, 2009 2 次提交
-
-
由 Jesse Brandeburg 提交于
drop variables that had cache lines modified in simultaneous hot paths. keep some variables modified on hot paths but make their storage per queue. cache align DMA data buffer start addresses. cache align (padding) some structures that end within a cacheline. Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jesse Brandeburg 提交于
decrease the memory utilization of the tx / rx queue allocation by changing the default ring size to 512 (from 1024). At 1024 rx entries of 2KB each (from 4kB slab) with 16 queues ixgbe was using 64 MB of memory per port, which is not necessary. Users can still change queue lengths with ethtool -k. Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 12月, 2009 1 次提交
-
-
由 Alexander Duyck 提交于
This patch removes skb_dma_map/unmap calls from the ixgbe driver due to the fact that the calls don't work with HW IOMMU enabled systems. The problem is that multiple mappings will give different results when HW IOMMU is enabled and the skb_dma_map/unmap calls only have one location to store mappings. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 11月, 2009 1 次提交
-
-
由 Mallikarjuna R Chilakala 提交于
Divide 82599 HWRSC counters into aggregated and flushed to count number of packets getting coalesced per TCP connection. Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 10月, 2009 1 次提交
-
-
由 Yi Zou 提交于
Implements the netdev_ops.ndo_fcoe_get_wwn in 82599 if it finds valid prefix for the World Wide Node Name (WWNN) or World Wide Port Name (WWPN), as well as valid SAN MAC address. Signed-off-by: NYi Zou <yi.zou@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 08 10月, 2009 1 次提交
-
-
由 Ajit Khaparde 提交于
Since net_device has an instance of net_device_stats, we can remove the instance of this from the private adapter structure. Signed-off-by: NAjit Khaparde <ajitk@serverengines.com> Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 07 10月, 2009 1 次提交
-
-
由 Stephen Hemminger 提交于
The data center bridging ops structure can be const Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 22 9月, 2009 1 次提交
-
-
由 Nelson, Shannon 提交于
Allow the user to set Tx specific itr values. This only makes sense when there are separate vectors for Tx and Rx. When the queues are doubled up RxTx on the vectors, we still only use the rx itr value. Signed-off-by: NShannon Nelson <shannon.nelson@intel.com> Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 9月, 2009 2 次提交
-
-
由 Yi Zou 提交于
Add support for dcbnl_rtnl_ops.setapp/getapp to set or get the current user priority bitmap for the given application protocol. Currently, 82599 only supports setapp/getapp for Fiber Channel over Ethernet (FCoE) protocol. Signed-off-by: NYi Zou <yi.zou@intel.com> Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yi Zou 提交于
This adds support to the net_device_ops.ndo_fcoe_enable/disable for 82599. This consequently allows us to dynamically turn FCoE offload feature on or off upon incoming calls to ndo_fcoe_enable/disable. When this happens, FCoE offload features are enabled/disabled accordingly, and this is regardless of whether DCB being turned on or not. Signed-off-by: NYi Zou <yi.zou@intel.com> Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 8月, 2009 1 次提交
-
-
由 Don Skidmore 提交于
We have some ~40 functions that were being called out with 'make namespacecheck'. This patch changes these functions to be static. Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 10 8月, 2009 1 次提交
-
-
由 Yi Zou 提交于
For 82599, packet split has to be disabled for FCoE direct data placement. However, this is only required on received queues allocated for FCoE. This patch adds a per ring flags to indicate if packet split is disabled on a per queue basis, particularly for FCoE, as packet split must be disabled for large receive using direct data placement (DDP). Signed-off-by: NYi Zou <yi.zou@intel.com> Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 31 7月, 2009 1 次提交
-
-
由 Peter P Waskiewicz Jr 提交于
When a user disables interrupt throttling with ethtool on 82599 devices, the interrupt timer may not be re-enabled if hardware RSC is running. The RSC completions in hardware don't complete before the next ITR event tries to fire, so the ITR timer never gets re-armed. This patch increases the amount of time between interrupts when throttling is disabled (rx-usecs = 0) when the hardware RSC deature is enabled. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 7月, 2009 1 次提交
-
-
由 Yi Zou 提交于
Currently, FCoE offload feature is turned on when the kernel config has CONFIG_FCOE or CONFIG_FCOE_MODULE set. However, we really want to turn FCoE offload on when there is FCoE traffic passing and turn it off when it's just LAN traffic. Since FCoE depends on a lossless network provided by DCB, this allows us to have FCoE turned on/off when user turns on DCB using dcbtool. Signed-off-by: NYi Zou <yi.zou@intel.com> Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 18 7月, 2009 1 次提交
-
-
由 Peter P Waskiewicz Jr 提交于
The ethtool offline test is the only consumer of the legacy descriptors. Update that path to only use advanced descriptors, and remove all support for legacy descriptors. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 07 6月, 2009 6 次提交
-
-
由 Jesse Brandeburg 提交于
This patch rearranges the ixgbe_ring struct to make better use of cacheline efficiency. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peter P Waskiewicz Jr 提交于
This patch enables Flow Director's ATR functionality to the main base driver for 82599. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Acked-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peter P Waskiewicz Jr 提交于
This patch adds the functions for ixgbe to initialize Flow Director. It also has the function APIs to add Flow Director filters from the base driver. This also includes ATR, Application Targeted Routing, which is a feature set of Flow Director. This is the hash-based mechanism to automatically identify flows and add filters based on the hash, and direct the Rx of that flow back to that same CPU. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peter P Waskiewicz Jr 提交于
This adds a second feature flag variable to use for future feature expansion. Add HW RSC to this new feature flags variable. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Duyck 提交于
The v_idx value was being used as both a bitmask and an index. This change makes it so that the q_vector contains the index and allows for much of the code to be simplified since disabling a q_vector involves only clearing one bit in the interrupt bitmask. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peter P Waskiewicz Jr 提交于
This patch adds support for the ethtool internal test engine. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 19 5月, 2009 1 次提交
-
-
由 Alexander Duyck 提交于
The performance of hardware RSC is greatly reduced if the total for max rsc descriptors multiplied by the buffer size is greater than 65535. To prevent this we need to adjust the max rsc descriptors appropriately. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 18 5月, 2009 6 次提交
-
-
由 Peter P Waskiewicz Jr 提交于
82599 supports using either link flow control or priority flow control when in DCB mode. The dcbnl interface already supports sending down configurations through rtnetlink that can enable LFC when DCB is enabled, so the driver should take advantage of this. 82598 does not support using LFC when DCB is enabled, so explicitly disable it when we're in DCB mode. This means we always run in PFC mode when DCB is enabled. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yi Zou 提交于
Enable jumbo frame when FCoE feature is enabled in 82599. Use 3K as the receive queue buffer size for receive queues used by FCoE to address for max Fiber Channel frame size as 2148 bytes (with max 2112 bytes of payload). Signed-off-by: NYi Zou <yi.zou@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yi Zou 提交于
Add ring feature for FCoE to make use of the FCoE redirection table in 82599. The FCoE redirection table is a receive side scaling feature for Fiber Channel over Ethernet feature in 82599, enabling distributing FCoE packets to different receive queues based on the exchange id. Signed-off-by: NYi Zou <yi.zou@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yi Zou 提交于
This patch implements the FCoE Rx side offload feature in ixgbe_main.c to 82599 using the Rx offload infrastructure code added in the previous patch. The large receive offload by Direct Data Placement (DDP) for FCoE is achieved by implementing the ndo_fcoe_ddp_setup and ndo_fcoe_ddp_done in net_device_ops via netdev. It is up to the ULD, i.e., fcoe and libfc to query and setup large receive offload accordingly through the corresponding netdev upon creating fcoe instances. Signed-off-by: NYi Zou <yi.zou@intel.com> Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yi Zou 提交于
This adds infrastructure code for FCoE Rx side offload feature to 82599, which provides large receive offload for FCoE by Direct Data Placement (DDP). The ixgbe_fcoe_ddp_get() and ixgbe_fcoe_ddp_put() pair corresponds to the netdev support to FCoE by the function pointers provided in net_device_ops as ndo_fcoe_ddp_setup and ndo_fcoe_ddp_done. The implementation of these in ixgbe is shown in the next patch. Signed-off-by: NYi Zou <yi.zou@intel.com> Signed-off-by: NChris Leech <christopher.leech@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yi Zou 提交于
This patch implements the FCoE Tx side offload features in ixgbe_main.c to 82599 using the Tx offload infrastructure code added in the previous patch. This is achieved by the calling the FCoE Sequence Offload (FSO) function ixgbe_fso() on the transmit path of ixgbe. This patch also includes an EEPROM check to make sure the NIC we're loading on is an offload-enabled SKU. Signed-off-by: NYi Zou <yi.zou@intel.com> Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-