Attached is a patch which fixes tuning to low frequency channels with
stb0899+tda8261 cards like the KNC TV-Station DVB-S2.
The cause of the issue was a broken if construct, which should have been
an if/else if, so that the setting for the lowest matching frequency is
applied.

Without this patch for example tuning to "arte" on Astra 19.2, 10744MHz
SR22000 failed most times and when it failed the communication between
driver and tda8261 was completely broken.
This problem disappears with the attached patch.
Signed-off-by: NJulian Scheel <julian@jusst.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add new USB ID (1b80:e400) for KWorld PlusTV Dual DVB-T Stick (DVB-T 399U).
The model number on the devices sticker label is "KW-DVB-T 399UR".
Signed-off-by: NMart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It seems from other code that it is the dst_type field rather than the
type_flags field that contains values of the form DST_TYPE_IS...
The type_flags field contains values of the form DST_TYPE_HAS...

The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@ struct dst_state E; @@

(
*E.type_flags ==
  \( DST_TYPE_IS_SAT\|DST_TYPE_IS_TERR\|DST_TYPE_IS_CABLE\|DST_TYPE_IS_ATSC \)
|
*E.type_flags !=
  \( DST_TYPE_IS_SAT\|DST_TYPE_IS_TERR\|DST_TYPE_IS_CABLE\|DST_TYPE_IS_ATSC \)
)
// </smpl>

Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support for Humax/Coex DVB-T USB Stick 2.0 High Speed
which is a very popular tuner sold in Vietnam.
Tested with at least 3 tuners.

Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NPham Thanh Nam <phamthanhnam.ptn@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The card includes Intel ce5039(Zarlink zl10039) tuner
and Intel ce6313 (Zarlink zl10313) demod.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The code from Jan D. Louw with some minor changes.
http://article.gmane.org/gmane.linux.drivers.dvb/38163
Tested with TeVii S630 DVB-S USB card by me (Igor)
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

do_div requires an u64 as the first argument, not a s64.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Acked-by: NPatrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use unified lgs8gxx frontend instead of reverse engineered lgs8gl5 frontend.
After this patch, lgs8gl5 frontend could be mark as deprecated.
Future development should base on unified lgs8gxx frontend.
Signed-off-by: NDavid T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support for the STK7700D USB-DVB-Device.

lsusb identifies it as:
idVendor           0x1164 YUAN High-Tech Development Co., Ltd
idProduct          0x1efc
 iProduct                2 STK7700D

The device is build into a Samsung R55-T5500 notebook.
Signed-off-by: NPete Hildebrandt <send2ph@googlemail.com>
Signed-off-by: NPatrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

cinergyInitialize param.flags.
Signed-off-by: NEberhard Mattes <eberhard.mattes@web.de>
Signed-off-by: NThierry MERLE <thierry.merle@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Replace printing to magically sized temporary buffer with use
of KERN_CONT for continual printing of eeprom registers dump.

Since deb_info is defined as dprintk, which is conditionally defined
to printk without additional parameters, meaning that deb_info is equivalent
to direct printk (without adding KERN_ facility), we can use KERN_DEBUG and
KERN_CONT in there, eliminating the need for sprintf into temporary buffer
with not easily readable/magical size.

Though it's strange, that deb_info definition uses printk without KERN_
facility and callers don't use it either.
Signed-off-by: NJan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Create card parameters array in SDMC DM1105 driver.
It is useful for cards with the same pci id, but different
tuners, lnb power control circuits, etc.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In automatic mode every stop event on SDA line ends repetition.
However, in  NetUP Dual card on the same i2c bus we have several devices.
If someone using both adapters to lock simultaneously or working with CAM interface
during lock procedure, it lead to end repetition prematurely quite often.
Set stv0900 i2c repeater to manual mode prevents such situation.
Signed-off-by: NAbylay Ospan <aospan@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The dvb-pll code should do the same thing that
alps_tdee4_stv0297_tuner_set_params() was doing.  Except the dvb-pll code
will check for tuner presence when attaching, while the old code didn't.

This tuner appears to not be behind the stv0297's I2C gate but is instead
on a different I2C adapter provided by the flexcop chip.  The old code
would turn the I2C gate off each time the tuner was used.  I've changed it
to turn the gate off when the tuner is attached and then disable the gate
control function.  This should result in the gate staying off, which should
be even better.

[hverkuil@xs4all.nl: fix compile error]
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The code in skystar23_samsung_tbdu18132_tuner_set_params() and
samsung_tbmu24112_tuner_set_params() is equivalent to what the dvb-pll code
does.  There could be an issue because the dvb-pll code will probe to check
for the tuner, while the previous code didn't do any checks.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The code in samsung_tdtc9251dh0_calc_regs() is equivalent to what dvb-pll's
code does.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

No datasheet, data take from code in flexcop driver.  That code rounded
down the divisor rather than rounding to nearest, which was probably not
intentional and the dvb-pll code will round to nearest.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Tuner parameters determined from code in flexcop driver.  That code rounded
the divisor down instead of to the nearest value.  This was probably not
intentional and the dvb-pll version will round to nearest.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Tuner parameters taken from flexcop driver.  This PLL has a 17 bit divisor
while the dvb-pll driver is designed for 15 bit divisors.  It's not a
problem as 15 bits is enough for the tuner's entire range.  But if a larger
range was wanted, it could be done by adding additional bands with the
extra divisor bits appearing as band switch bits.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

No datasheet, tuner data comes from code in flexcop driver.  This tuner is
also used on the AVerTV 771 supported by the bttv driver, but that code
uses a different tuner configuration, which is surprising.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Values for 'pid' range from 0 to 0x1fff. Therefore 'feed->pid' can never
be equal to both 'pid' and 0x2000. This makes the continue statement have
no effect.
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

DMX_ADD_PID allows to add multiple PIDs to a transport stream filter
previously set up with DMX_SET_PES_FILTER and output=DMX_OUT_TSDEMUX_TAP.

DMX_REMOVE_PID is used to drop a PID from a filter.

These ioctls are to be used by readers of /dev/dvb/adapterX/demuxY. They
may be called at any time, i.e. before or after the first filter on the
shared file descriptor was started.

They make it possible to record multiple services without the need to de-
or re-multiplex TS packets.

To accomplish this, dmxdev_filter->feed.ts has been converted to a list
of struct dmxdev_feeds, each containing a PID value and a pointer to a
struct dmx_ts_feed.
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

lgs8gxx: add lgs8g75 demodulator support
Signed-off-by: NDavid T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch fixes some checkpatch warnings in mt312-driver.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

input, inp and i are unsigned. When negative they are wrapped and caught by the
other test.

Cc: Andy Walls <awalls@radix.net>
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Cc: Patrick Boettcher <patrick.boettcher@desy.de>
Cc: Steven Toth <stoth@linuxtv.org>
Cc: Igor M. Liplianin <liplianin@netup.ru>
Cc: Srinivasa Deevi <srinivasa.deevi@conexant.com>
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Update KConfig file to enbale selection of SDIO and USB
interfaces, and add dependancy on relevant modules.

[mchehab@redhat.com: fix merge conflicts, remove default: m, add missing endmenu]
Signed-off-by: NUdi Atar <udia@siano-ms.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixed SDIO compilation bugs
Also fixed a memory overrun issue in buffer management.
Signed-off-by: NUdi Atar <udia@siano-ms.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Previous changesets broke Hauppauge devices and their GPIO configurations.

This changeset restores the LED & LNA functionality.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With mode DEVICE_MODE_RAW_TUNER a read occurs past the end of smscore_fw_lkup[].
Subsequently an attempt is made to load the firmware from the resulting
filename.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch changes most frontend drivers to allocate their state structure via
kzalloc and not kmalloc. This is done to properly initialize the
embedded "struct dvb_frontend frontend" field, that they all have.

The visible effect of this struct being uninitalized is, that the member "id"
that is used to set the name of kernel thread is totally random.

Some board drivers (for example cx88-dvb) set this "id" via
videobuf_dvb_alloc_frontend but most do not.

So I at least get random id values for saa7134, flexcop and ttpci based cards.
It looks like this in dmesg:
DVB: registering adapter 1 frontend -10551321 (ST STV0299 DVB-S)

The related kernel thread then also gets a strange name
like "kdvb-ad-1-fe--1".

Cc: Michael Krufky <mkrufky@linuxtv.org>
Cc: Steven Toth <stoth@linuxtv.org>
Cc: Timothy Lee <timothy.lee@siriushk.com>
Cc: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Acked-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

siano uses input_*() functions so it should depend on INPUT
to prevent build errors:

ERROR: "input_event" [drivers/media/dvb/siano/sms1xxx.ko] undefined!
ERROR: "input_register_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined!
ERROR: "input_free_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined!
ERROR: "input_unregister_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined!
ERROR: "input_allocate_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined!

Cc: Michael Krufky <mkrufky@linuxtv.org>
Cc: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove the following build warning:

sms-cards.c: In function 'sms_board_event':
sms-cards.c:120: warning: unused variable 'board'

Thanks to Hans Verkuil for pointing this out.

The problem code has been #if 0'd for now, this will likely be
used again in the future, once the event interface is complete.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The current GPIO configuration breaks all Hauppauge devices.

The code being removed affects Hauppauge devices only,
and is the cause of the breakage.
Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Moving BOOT fixes problem.
Signed-off-by: NNils Kassube <kassube@gmx.net>
Acked-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixes stack corruption bug present in dump_regs function of zl10353 and
qt1010 drivers: the buffer buf was one byte smaller than required -
there are 4 chars for address prefix, 16 * 3 chars for dump of 16 eeprom
bytes per line and 1 byte for zero ending the string required, i.e. 53
bytes, but only 52 were provided.

The one byte missing in stack based buffer buf can cause stack
corruption possibly leading to kernel oops, as discovered originally
with af9015 driver (af9015: fix stack corruption bug).
Signed-off-by: NJan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>