The snd_soc_dapm_xxxx_pin all require the dapm_mutex to be held when
they are called as they edit the dirty list, however very few of the
callers do so.

This patch adds unlocked versions of all the functions replacing the
existing implementations with one that holds the lock internally. We
also fix up the places where the lock was actually held on the caller
side.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

The error messages for bypassing/unbypassing a regulator appear to be
swapped round, this patch corrects these.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Commit 384a48d7 "ALSA: hda: HDMI: Support codecs with fewer cvts
than pins" dynamically enabled each pin widget's PIN_OUT only when the
pin was actively in use. This was required on certain NVIDIA CODECs for
correct operation. Specifically, if multiple pin widgets each had their
mux input select the same audio converter widget and each pin widget had
PIN_OUT enabled, then only one of the pin widgets would actually receive
the audio, and often not the one the user wanted!

However, this apparently broke some Intel systems, and commit
6169b673 "ALSA: hda - Always turn on pins for HDMI/DP" reverted the
dynamic setting of PIN_OUT. This in turn broke the afore-mentioned NVIDIA
CODECs.

This change supports either dynamic or static handling of PIN_OUT,
selected by a flag set up during CODEC initialization. This flag is
enabled for all recent NVIDIA GPUs.
Reported-by: NUosis <uosisl@gmail.com>
Cc: <stable@vger.kernel.org> # v3.13
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When we plug a 3-ring headset on the Dell machine (Vendor ID:
0x10ec0255, Subsystem ID: 0x1028064d), the headset mic can't be
detected, after apply this patch, the headset mic can work well.

BugLink: https://bugs.launchpad.net/bugs/1260303
Cc: David Henningsson <david.henningsson@canonical.com>
Tested-by: NDoro Wu <fan-cheng.wu@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: NHui Wang <hui.wang@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Remove old SPI control functions, change anti-pop init
sequence, remove some garbage from structures. The 'Apply' functions
must be called at the mixer initialization, otherwise
mixer settings sometimes will not be applied at startup.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Change the 'put' function of the high-pass filter control to use the new
SPI functions.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

First of all, we should not touch the GPIOs. They are not
for selecting the capture source, but they seems just enable
the whole audio input curcuit. The 'put' function calls the
'apply' functions to change register values. Change the order
of capture sources.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Modify the input_vol_* functions to use the new SPI routines,
There is a new applying function that will be called when
the capture source changed.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

I tried both variants: volume control and impedance selector.
In the first case one minus is that we can't change the
volume of multichannel output without additional software
volume control. However, I am using this variant for the
last three months and this seems good. All multichannel
speaker systems have internal amplifier with the
volume control included, but not all headphones have
this regulator. In the second case, my software volume
control does not save the value after reboot.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Change the order of elements in the output select control. This will
reduce the number of relay switches. Change 'put' function to call the
oxygen_update_dac_routing() function. Otherwise multichannel playback
does not work. Also there is a new function to apply settings, this
prevents from duplicating the code.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Actually CS4245 connected to the I2S channel 1 for
capture, not channel 2. Otherwise capturing and
playback does not work for CS4245.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Moving the mixer code away makes things easier. The mixer
will control the driver, so the functions of the
driver need to be non-static.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Change the function to read the data from the new shadow buffer.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

When selecting the audio output destinations (headphones,
FP headphones, multichannel output), the channel routing
should be changed depending on what destination selected.
Also unnecessary I2S channels are digitally muted. This
function called when the user selects the destination
in the ALSA mixer.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

When selecting the audio sample rate for CS4245,
the MCLK divider should also be changed.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Change CS4245 initialization: different sequence and GPIO values,
according to datasheets and reverse-engineering information.
Change cleanup/resume/suspend functions, since they use
initialization.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Add the new SPI write and read functions. The SPI read function
is used for creating initial registers dump and may be used for
debugging purposes. SPI operations are cached, so there is a new
function to manage the cache (shadow). I have to remove
the shift from the CS4245_SPI_* constants, since when
we are performing the reading, we need to shift by 8 instead
of 16.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Add additional constants to the xonar_dg.h file:
capture and playback sources. Move GPIO_* constants and the
dg struct to the header file from the xonar_dg.c file.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Add some additional information in comments and my copyright.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

When the user switches the output from stereo to multichannel
or vice versa, the driver needs to update the channel routing.
Instead of creating additional subroutines, I better export existing
oxygen_update_dac_routing symbol from the oxygen mixer
and call this function. It calls model.adjust_dac_routing()
and my function does the work.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

The Xonar DG/DGX driver needs this mask to mute unnecessary
channels.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Modify the oxygen_write_spi() function to use the newly
introduced oxygen_wait_spi() function. Change return value
from void to int, so it can return error codes. Older
drivers just ignore that return value, new drivers can
check this value. We need to wait AFTER
initiating the SPI transaction, otherwise read
operation will not work.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

The oxygen_wait_spi() function now performs waiting when the
SPI bus completes a transaction. Introduce the timeout error
checking and increase timeout to 200 from 40.
Signed-off-by: NRoman Volkov <v1ron@mail.ru>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Processing coefficients are often a vital part of the codec's configuration,
so dumping them can be important. However, because they are undocumented and
secret, we do not want to enable this for all codecs by default.

Therefore instead add this as a debugging parameter.

I have prepared for codecs that want to enable this by default by the extra
dump_coef bitfield, but unsure if we want to do that as long as the
(unlikely, but still) race remains.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Currently the Negative Terminal Input Routing Configuration is only set
when there is a special routing configuration. If we don't use one of
the inputs IN1 or IN2 as negative terminal input, the PGA and recording
does not work.

This patch adds a route from CM1L/CM1R to the PGA as negative input by
default. With this configuration the PGA can amplify all input signals
and line-in/mic works again.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Playback of a mono stream should output the same stream on both
channels. At the moment only the left analog signal is valid, the right
one is just noise.

This patch maps the left digital channel onto both DACs when receiving a
mono stream.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Similarly to other Apple products, MBA 1,1 needs a specific quirk.
Pin 0x18 must be set to VREF_50 to have sound output.  This was no
longer done since commit 1a97b7f2, resulting in a mute built-in speaker.

This patch corrects the regression by creating a fixup for the MBA 1,1.

Fixes: 1a97b7f2 ("ALSA: hda/realtek - Remove the last static quirks for ALC882")
Cc: <stable@vger.kernel.org> [v3.4+]
Tested-by: NAdrien Vergé <adrienverge@gmail.com>
Signed-off-by: NAdrien Vergé <adrienverge@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

mach/dma.h is not referenced by this file. Remove it.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

'res' could be NULL from one of the operations above (line 1243). Thus
check 'res' for NULL before releasing the region to avoid null pointer
dereference.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Depend on MFD_ARIZONA to avoid the following build errors:

sound/soc/codecs/arizona.c:218: undefined reference to `arizona_request_irq'
sound/soc/codecs/arizona.c:226: undefined reference to `arizona_request_irq'
sound/soc/codecs/arizona.c:1719: undefined reference to `arizona_request_irq'
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Select S3C24XX_DMA instead of S3C2410_DMA to avoid following dependency issues
and build errors:

warning: (CPU_S3C2410 && CPU_S3C2442 && SND_SOC_SAMSUNG && SND_S3C24XX_I2S && SND_S3C2412_SOC_I2S && SND_SOC_SAMSUNG_SMDK2443_WM9710 && SND_SOC_SAMSUNG_LN2440SBC_ALC650) selects S3C2410_DMA which has unmet direct dependencies (ARCH_S3C24XX && S3C24XX_DMA && (CPU_S3C2410 || CPU_S3C2442))
warning: (CPU_S3C2410 && CPU_S3C2442 && SND_SOC_SAMSUNG && SND_S3C24XX_I2S && SND_S3C2412_SOC_I2S && SND_SOC_SAMSUNG_SMDK2443_WM9710 && SND_SOC_SAMSUNG_LN2440SBC_ALC650) selects S3C2410_DMA which has unmet direct dependencies (ARCH_S3C24XX && S3C24XX_DMA && (CPU_S3C2410 || CPU_S3C2442))

arch/arm/mach-s3c24xx/built-in.o: In function `s3c2410_dma_add':
arch/arm/mach-s3c24xx/dma-s3c2410.c:134: undefined reference to `s3c2410_dma_init'
arch/arm/mach-s3c24xx/dma-s3c2410.c:135: undefined reference to `s3c24xx_dma_order_set'
arch/arm/mach-s3c24xx/dma-s3c2410.c:136: undefined reference to `s3c24xx_dma_init_map'
arch/arm/plat-samsung/include/plat/dma-ops.h:60: undefined reference to `s3c_dma_get_ops'
sound/soc/samsung/s3c24xx-i2s.c:293: undefined reference to `s3c2410_dma_ctrl'
arch/arm/plat-samsung/include/plat/dma-ops.h:60: undefined reference to `s3c_dma_get_ops'
arch/arm/plat-samsung/include/plat/dma-ops.h:60: undefined reference to `s3c_dma_get_ops'
sound/built-in.o: In function `s3c2412_i2s_trigger':
sound/soc/samsung/s3c-i2s-v2.c:432: undefined reference to `s3c2410_dma_ctrl'
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Export the symbol so that it is accessible to modules. Fixes the
following error:

ERROR: "wm5100_detect" [sound/soc/samsung/snd-soc-lowland.ko] undefined!
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

There are two loops that are almost identical but only with different
checks.  Refactor them with a simple helper, and give a bit more
comments what's doing there.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The test here is intended intended to prevent shift wrapping bugs when
we do "1U << idx2".  We should consider the number of bits in a u32
instead of the number of bytes.

[fix another chunk similarly by tiwai]

Fixes: 7bb2491b ('ALSA: Add kconfig to specify the max card numbers')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fixes the following build error and warning when OF is not defined:
sound/soc/samsung/smdk_wm8994.c:191:23: error: ‘samsung_wm8994_of_match’ undeclared (first use in this function)
sound/soc/samsung/smdk_wm8994.c:47:32: warning: ‘smdk_board_data’ defined but not used [-Wunused-variable]

of_match_ptr() is used so that samsung_wm8994_of_match gets dropped (as unused)
by the compiler when OF is not defined.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Fixes the following error introduced by commit eca3b01d
("ASoC: switch over to use snd_soc_register_component() on s3c i2s"):
sound/soc/samsung/s3c-i2s-v2.c:732:32: error: ‘drv’ undeclared (first use in this function)
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Recent changes through commits c67d0f29 ("ARM: s3c24xx: get rid
of custom <mach/gpio.h>"), b0161caa ("ARM: S3C[24|64]xx: move includes
back under <mach/> scope"), 36437412 ("ARM: s3c24xx: explicit
dependency on <plat/gpio-cfg.h>") and 41c3548e ("ARM: s3c64xx: get rid
of custom <mach/gpio.h>") caused build regressions due to broken
dependencies. Fix the following errors by including the necessary header
files explicitly:

sound/soc/samsung/h1940_uda1380.c:56:3: error: implicit declaration of function ‘S3C2410_GPG’
sound/soc/samsung/h1940_uda1380.c:149:18: error: ‘S3C_GPIO_END’ undeclared (first use in this function)
sound/soc/samsung/h1940_uda1380.c:234:21: error: ‘S3C_GPIO_END’ undeclared (first use in this function)
sound/soc/samsung/h1940_uda1380.c:270:12: error: ‘S3C_GPIO_END’ undeclared (first use in this function)
sound/soc/samsung/neo1973_wm8753.c:239:2: error: implicit declaration of function ‘S3C2410_GPJ’
sound/soc/samsung/rx1950_uda1380.c:67:3: error: implicit declaration of function ‘S3C2410_GPG’
sound/soc/samsung/s3c2412-i2s.c:86:2: error: implicit declaration of function ‘s3c_gpio_cfgall_range’
sound/soc/samsung/s3c2412-i2s.c:86:2: error: implicit declaration of function ‘S3C2410_GPE’
sound/soc/samsung/s3c2412-i2s.c:86:2: error: implicit declaration of function ‘S3C_GPIO_SFN’
sound/soc/samsung/s3c2412-i2s.c:87:10: error: ‘S3C_GPIO_PULL_NONE’ undeclared
sound/soc/samsung/s3c24xx-i2s.c:394:2: error: implicit declaration of function ‘s3c_gpio_cfgall_range’
sound/soc/samsung/s3c24xx-i2s.c:394:2: error: implicit declaration of function ‘S3C2410_GPE’
sound/soc/samsung/s3c24xx-i2s.c:394:2: error: implicit declaration of function ‘S3C_GPIO_SFN’
sound/soc/samsung/s3c24xx-i2s.c:395:10: error: ‘S3C_GPIO_PULL_NONE’ undeclared
sound/soc/samsung/smartq_wm8987.c:112:3: error: implicit declaration of function ‘S3C64XX_GPL’
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

ASUS Zenbook UX31A has yet another problem -- softer output level than
others.  According to the measurement, the peak output difference
between 31A and 31E is 5dB.  As ALC269VB has a COEF for the class-D
pre-amp, let's apply it for +5dB.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The release of module object itself was forgotten.
Spotted by COVERIY CID 1162828.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Currently everytime we get the following message on boot:

fsl-ssi-dai 202c000.ssi: could not get baud clock: -2

This is not really useful information to get on every boot, so make it a debug
message instead.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>