Patch from Lennert Buytenhek

Unify the five existing ixp2000 defconfigs into one defconfig.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

The original version of the chip docs had the PW and SU fields in
the slowport write timing control register accidentally reversed.
This is mentioned in the errata (documentation change #4) and fixed
in newer docs.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

On the IXDP2x00s, the NPU that is PCI master is always the egress
(i.e. 'master') NPU.  At least on the IXDP2800, both NPUs have flash,
so the ixp2000_has_flash() check in ixdp2x00_master_npu() is useless.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

The xscale UART in the ixp2000 is basically just an 8250 UART (with
some extra bits and pieces), so we can use the generic 8250 debug
macros on the ixp2000.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

ixp2000 used to initially mark GPIO interrupts as invalid, and not
mark them valid until set_irq_type() was called, but this doesn't
work if you want to use request_irq() with the SA_TRIGGER_* flags.

So, just mark the GPIO interrupts valid from the beginning.  We
configure GPIOs as inputs when set_irq_type() is called anyway, so
this shouldn't be a problem.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Only issue a "nobody cared" warning after 99900 spurious interrupts.
This avoids the occasional spurious interrupt causing warnings, as
per x86.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We need this to be zero initialised.  Since this is an array, use kcalloc
rather than kzalloc or kmalloc.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

op_arm_sem is being used as a mutex, so convert it to use
real mutexes.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Add Simtec Osiris to the default build, and enable the
USB-OHCI section by default.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Fix the build of arch/arm/mach-s3c2410/mach-osiris.c
and fix the warnings from sparse.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

Add GPIO interrupt support for the first 16 GPIO lines (port A
and B.)
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Add USB bus clock definition for 48MHz fed to OHCI and gadget cores
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Add set_rate methods for the extra clocks on the S3C2440
and add the camera UPLL clock source
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Add support for clk_set_rate and clk_round_rate to the
s3c2410 clock implementation
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Convert all uses of kmalloc followed by memset to use kzalloc instead.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

Move the uengine loader from arch/arm/mach-ixp2000 to arch/arm/common
so that ixp23xx can use it too.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

Add ep93xx defconfig.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

Add support for setting the direction of and getting/setting the
value of the 64 GPIO lines.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

This patch adds support for the Cirrus ep93xx series of CPUs.  The
ep93xx is an ARM920T based CPU with two VICs, PL010 based UARTs,
IrDA, MaverickCrunch floating point coprocessor, between 24 and 64
GPIOs, ethernet, OHCI USB and, depending on the model, pcmcia, raster
engine, graphics accelerator, IDE controller and a bunch of other
stuff.

This patch adds the core ep93xx support code, and support for the
Glomation GESBC-9312-sx and the Technologic Systems TS-72xx SBCs.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Alessandro Zummo

ixp4xx_config_irq did not configure the gpio line
as an input.

As an added bonus, the irq2gpio array has been converted
from int to char.
Signed-off-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Alessandro Zummo

This patch adds a few defines that are useful
to configure the CS regions on ixp4xx.
Signed-off-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NOEyvind Repvik <oyvind@repvik.org>
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Peter Teichmann

Currently, if the kernels HZ value is greater than 100, delays with the udelay function are too short. This can cause trouble for instance with the zd1201 usb wlan driver.

This patch suggests a solution that keeps the overhead small and maintains (hopefully) sufficient resolution.

Signed-off-by: Peter Teichmann
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Deepak Saxena

This patch adds support for Intel's IXDP28x5 platform. This
is just and IXDP2801 with a new CPU rev but the bootloader
has been updated to reflect a new machine ID so we just build
support for it by default when we build IXDP2801.
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Add enable and set_parent calls for the dclk
and clkout clocks.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Add devices that we have drivers for, and
update list of machines that are supported
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Add clk_set_parent() call to clock code
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Move the UPLL clock registration to the central
clock file, and add an enable method
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Add selection for timer code for the Simtec Osiris
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Ben Dooks

Support for Simtec IM2440D20 CPU modules (Osiris)
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

This field is redundent since it must be equal to PHYS_OFFSET anyway.

There is no reference to it anymore so remove it at last.
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Several ARM machine implementations used a PL01x primecell compatible
serial port for debugging purposes, and indepdently implemented the low
level debug macros every time.  Provide a common implementation and
convert these implementations to use this version.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Several ARM machine implementations used an 8250 compatible port for
debugging purposes, and indepdently implemented the low level debug
macros every time.  Provide a common implementation and convert these
implementations to use this version.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This needs asm/hardware.h - include it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Some SoCs have multiple VIC devices.  Adapt the generic vic code
to allow multiple implementations to be handled.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

In all current use cases, "chipdata" is used to store an iomem address.
Mark it with __iomem, and rename it to 'base'.  Leave the accessor macros
alone.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Allow the individual coprocessor handlers to decide when to enable
interrupts, rather than unconditionally enabling them.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

asm/hardware.h is not required for the majority of processor support
files, ioremap support, mm initialisation, acorn IO support, nor
the debug code (which picks up its machine specific includes via
debug-macros.S)
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Unfortunately, OMAP platforms without the 32K timer left HZ set to
an empty value.  Fix this by making the dependency on OMAP_32K_TIMER
rather than OMAP_32K_TIMER_HZ.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>