For i.MX6SX enet use AXI bus, reset MAC will make system bus dead
if ENET-AXI bus has pending access (AHB bus should not have such issue).
So, disable enet with AVB MAC instead of reset MAC itself.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

initilized all queues according to queue number get from DT file.
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDuan Fugang <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default, the tx/rx queue number is 1, user can config the queue number
at DTS file like this:
	fsl,num-tx-queues=<3>;
	fsl,num-rx-queues=<3>

Since i.MX6SX enet-AVB IP support multi queues, so use multi queues
interface to allocate and set up an Ethernet device.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch just change data structure to support multi-queue.
Only 1 queue enabled.

Ethernet multiqueue mechanism can improve performance in SMP system.
For single hw queue, multiqueue can balance cpu loading.
For multi hw queues, multiple cores can process network packets in parallel,
and refer the article for the detail advantage for multiqueue:
http://vger.kernel.org/~davem/davem_nyc09.pdfSigned-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFrank Li <frank.li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add enet AVB feature macro define for imx6sx.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

i.MX6sx enet has below clocks for user config:
clk_ipg: ipg_clk_s, ipg_clk_mac0_s, 66Mhz
clk_ahb: enet system clock, it is enet AXI clock for imx6sx.
	 For imx6sx, it alos is the clock source of interrupt coalescing.
	 The clock range: 200Mhz ~ 266Mhz.
clk_ref: refrence clock for tx and rx. For imx6sx enet RGMII mode,
	 the refrence clock is 125Mhz coming from internal PLL or external.
	 In i.MX6sx-arm2 board, the clock is from internal PLL.
	 clk_ref is optional, depends on board.
clk_enet_out: The clock can be output from internal PLL. It can supply 50Mhz
	 clock for phy. clk_enet_out is optional, depends on chip and board.
clk_ptp: 1588 ts clock. It is optional, depends on chip.

The patch add clk_ref to distiguish the different clocks.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the Marvell driver with some cleanups by Claudio Leite
and myself.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Cc: Claudio Leite <leitec@staticky.com>
Signed-off-by: NClaudio Leite <leitec@staticky.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sathya Perla says:

====================
be2net: patch set

Patch 1 fixes some minor issues with log messages in be2net.

Patch 2 replaces strcpy() calls with strlcpy() to avoid possible buffer
overflow.

Patch 3 improves the RX buffer posting scheme for jumbo frames.

Patch 4 replaces the use of v0 of SET_FLOW_CONTROL cmd with v1 to receive
a definitive completion status from FW.

Patch 5 adds support for ethtool "-m" ethtool option.

Patch 6 fixes port-type reporting via ethtool get_settings for QSFP/SFP+
interfaces.

Patch 7 fixes the usage of MODIFY_EQD FW cmd to target a max of 8 EQs on
Lancer chip.

Patch 8 enables PCIe error reporting even for VFs.

Pls consider applying this patch set to net-next. Thanks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently PCIe error reporting is enabled only on PFs. This patch enables
this feature on VFs too as Lancer VFs support it.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MODIFY_EQ_DELAY FW cmd on Lancer is supported for a max of 8 EQs per cmd.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report the ethtool port-type/supported/advertising values based on the
cable_type for QSFP and SFP+ interfaces. The cable_type is parsed from
the transceiver data fetched from the FW.
Signed-off-by: NRavikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: NSuresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the dump-module-eeprom and module-info
ethtool options.
Signed-off-by: NMark Leonard <mark.leonard@emulex.com>
Signed-off-by: NSuresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some configurations the FW doesn't allow changing flow control settings
of a link. Unless a v1 version of the SET_FLOW_CONTROL cmd is used, the FW
doesn't report an error to the driver.
Signed-off-by: NSuresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the RX path, the driver currently consumes upto 64 (budget) packets in
one NAPI sweep. When the size of the packet received is larger than a
fragment size (2K), more than one fragment is consumed for each packet.
As the driver currently posts a max of 64 fragments, all the consumed
fragments may not be replenished. This can cause avoidable drops in RX path.
This patch fixes this by posting a max(consumed_frags, 64) frags. This is
done only when there are atleast 64 free slots in the RXQ.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace strcpy with strlcpy, as it avoids a possible buffer overflow.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the following minor issues with log messages in be2net:
  1) Period is not required at the end of log message.
  2) Remove "Unknown grp5 event" logs to reduce noise. The driver can safely
     ignore async events from FW it's not interested in.
  3) Reword a log message for better readability to say that SRIOV
     "is disabled" rather than "not supported".
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we have 2 pkt_type_offset functions doing the same thing and
spread across the architecture files. Remove those and replace them
with a PKT_TYPE_OFFSET macro helper which gets the constant value from a
zero sized sk_buff member right in front of the bitfield with offsetof.
This new offset marker does not change size of struct sk_buff.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: NDenis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we introduced an additional multiplexing/demultiplexing layer
with commit 3e8a72d1 ("net: dsa: reduce number of protocol hooks")
that lives within the DSA code, we no longer need to have a given switch
driver tag_protocol be an actual ethertype value, instead, we can
replace it with an enum: dsa_tag_protocol.

Do this replacement in the drivers, which allows us to get rid of the
cpu_to_be16()/htons() dance, and remove ETH_P_BRCMTAG since we do not
need it anymore.
Suggested-by: NAlexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support hw VLAN for tx and rx. And enable them by default.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of error, the function devm_ioremap_resource() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If IPv6 is explicitly disabled before the interface comes up,
it makes no sense to continue when it comes up, even just
print a message.

(I am not sure about other cases though, so I prefer not to touch)
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cong Wang says:

====================
ipv6: clean up locking code in anycast and mcast

This patchset cleans up the locking code in anycast.c and mcast.c
and makes the refcount code more readable.
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>

v1 -> v2:
* refactor some code and make it in a separated patch
* update comments
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor out allocation and initialization and make
the refcount code more readable.
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similarly the code is already protected by rtnl lock.
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similarly the code is already protected by rtnl lock.
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor out allocation and initialization and make
the refcount code more readable.
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make it accept inet6_dev, and rename it to __ipv6_dev_ac_inc()
to reflect this change.
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just move rtnl lock up, so that the anycast list can be protected
by rtnl lock now.
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These code is now protected by rtnl lock, rcu read lock
is useless now.
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
bonding: get rid of curr_slave_lock

This is the second patch-set dealing with bond locking and the purpose here
is to convert curr_slave_lock into a spinlock called "mode_lock" which can
be used in the various modes for their specific needs. The first three
patches cleanup the use of curr_slave_lock and prepare it for the
conversion which is done in patch 4 and then the modes that were using
their own locks are converted to use the new "mode_lock" giving us the
opportunity to remove their locks.
This patch-set has been tested in each mode by running enslave/release of
slaves in parallel with traffic transmission and miimon=1 i.e. running
all the time. In fact this lead to the discovery of a subtle bug related to
RCU which will be fixed in -net.
Also did an allmodconfig test just in case :-)

v2: fix bond_3ad_state_machine_handler's use of mode_lock and
    curr_slave_lock
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that locks have been removed, remove some unnecessary comments and
adjust others to reflect reality. Also add a comment to "mode_lock" to
describe its current users and give a brief summary why they need it.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have bond->mode_lock, we can remove the state_machine_lock
and use it in its place. There're no fast paths requiring the per-port
spinlocks so it should be okay to consolidate them into mode_lock.
Also move it inside the unbinding function as we don't want to expose
mode_lock outside of the specific modes.
Suggested-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ALB/TLB specific spinlocks are no longer necessary as we now have
bond->mode_lock for this purpose, so convert them and remove them from
struct alb_bond_info.
Also remove the unneeded lock/unlock functions and use spin_lock/unlock
directly.
Suggested-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

curr_slave_lock is now a misleading name, a much better name is
mode_lock as it'll be used for each mode's purposes and it's no longer
necessary to use a rwlock, a simple spinlock is enough.
Suggested-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mostly all users of curr_slave_lock already have RTNL as we've discussed
previously so there's no point in using it, the one case where the lock
must stay is the 3ad code, in fact it's the only one.
It's okay to remove it from bond_do_fail_over_mac() as it's called with
RTNL and drops the curr_slave_lock anyway.
bond_change_active_slave() is one of the main places where
curr_slave_lock was used, it's okay to remove it as all callers use RTNL
these days before calling it, that's why we move the ASSERT_RTNL() in
the beginning to catch any potential offenders to this rule.
The RTNL argument actually applies to all of the places where
curr_slave_lock has been removed from in this patch.
Also remove the unnecessary bond_deref_active_protected() macro and use
rtnl_dereference() instead.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

First in rlb_teach_disabled_mac_on_primary() it's okay to remove
curr_slave_lock as all callers except bond_alb_monitor() already hold
RTNL, and in case bond_alb_monitor() is executing we can at most have a
period with bad throughput (very unlikely though).
In bond_alb_monitor() it's okay to remove the read_lock as the slave
list is walked with RCU and the worst that could happen is another
transmitter at the same time and thus for a period which currently is 10
seconds (bond_alb.h: BOND_ALB_LP_TICKS).
And bond_alb_handle_active_change() is okay because it's always called
with RTNL. Removed the ASSERT_RTNL() because it'll be inserted in the
parent function in a following patch.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the read_lock in bond_3ad_lacpdu_recv() since when the slave is
being released its rx_handler is removed before 3ad unbind, so even if
packets arrive, they won't see the slave in an inconsistent state.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

virtqueue_add() populates the virtqueue descriptor table from the sgs
given.  If it uses an indirect descriptor table, then it puts a single
descriptor in the descriptor table pointing to the kmalloc'ed indirect
table where the sg is populated.

Previously vring_add_indirect() did the allocation and the simple
linear layout.  We replace that with alloc_indirect() which allocates
the indirect table then chains it like the normal descriptor table so
we can reuse the core logic.

This slows down pktgen by less than 1/2 a percent (which uses direct
descriptors), as well as vring_bench, but it's far neater.

vring_bench before:
	1061485790-1104800648(1.08254e+09+/-6.6e+06)ns
vring_bench after:
	1125610268-1183528965(1.14172e+09+/-8e+06)ns

pktgen before:
   787781-796334(793165+/-2.4e+03)pps 365-369(367.5+/-1.2)Mb/sec (365530384-369498976(3.68028e+08+/-1.1e+06)bps) errors: 0

pktgen after:
   779988-790404(786391+/-2.5e+03)pps 361-366(364.35+/-1.3)Mb/sec (361914432-366747456(3.64885e+08+/-1.2e+06)bps) errors: 0

Now, if we make force indirect descriptors by turning off any_header_sg
in virtio_net.c:

pktgen before:
  713773-721062(718374+/-2.1e+03)pps 331-334(332.95+/-0.92)Mb/sec (331190672-334572768(3.33325e+08+/-9.6e+05)bps) errors: 0
pktgen after:
  710542-719195(714898+/-2.4e+03)pps 329-333(331.15+/-1.1)Mb/sec (329691488-333706480(3.31713e+08+/-1.1e+06)bps) errors: 0
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We used to have several callers which just used arrays.  They're
gone, so we can use sg_next() everywhere, simplifying the code.

On my laptop, this slowed down vring_bench by 15%:

vring_bench before:
	936153354-967745359(9.44739e+08+/-6.1e+06)ns
vring_bench after:
	1061485790-1104800648(1.08254e+09+/-6.6e+06)ns

However, a more realistic test using pktgen on a AMD FX(tm)-8320 saw
a few percent improvement:

pktgen before:
  767390-792966(785159+/-6.5e+03)pps 356-367(363.75+/-2.9)Mb/sec (356068960-367936224(3.64314e+08+/-3e+06)bps) errors: 0

pktgen after:
   787781-796334(793165+/-2.4e+03)pps 365-369(367.5+/-1.2)Mb/sec (365530384-369498976(3.68028e+08+/-1.1e+06)bps) errors: 0
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>