We never change those, make them r/o.
Signed-off-by: NMathias Krause <minipli@googlemail.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We never change emulate_ops[] at runtime so it should be r/o.
Signed-off-by: NMathias Krause <minipli@googlemail.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The opcode tables never change at runtime, therefor mark them const.
Signed-off-by: NMathias Krause <minipli@googlemail.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

As the the compiler ensures that the memory operand is always aligned
to a 16 byte memory location, use the aligned variant of MOVDQ for
read_sse_reg() and write_sse_reg().
Signed-off-by: NMathias Krause <minipli@googlemail.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Some fields can be constified and/or made static to reduce code and data
size.

Numbers for a 32 bit build:

        text    data     bss     dec     hex filename
before: 3351      80       0    3431     d67 cpuid.o
 after: 3391       0       0    3391     d3f cpuid.o
Signed-off-by: NMathias Krause <minipli@googlemail.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

kvm_pic_reset() is not used anywhere. Move reset logic from
pic_ioport_write() there.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

We will enter the guest with G and D cleared; as real hardware ignores D in
real mode, and G is taken care of by the limit test, we allow more code to
run in vm86 mode.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

While this is undocumented, real processors do not reload the segment
limit and access rights when loading a segment register in real mode.
Real programs rely on it so we need to comply with this behaviour.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

emulate_invalid_guest_state=1 doesn't mean we don't munge the segments in the
vmcs; we do.  So we need to return the real ones (maintained by vmx_set_segment).
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

We want the segment selector, nor segment number.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Segment limits are verified in real mode, not just protected mode.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

When loading a segment in real mode, only the base and selector must
be modified.  The limit needs to be left alone, otherwise big real mode
users will hit a #GP due to limit checking (currently this is suppressed
because we don't check limits in real mode).
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Usually, big real mode uses large (4GB) segments.  Currently we don't
virtualize this; if any segment has a limit other than 0xffff, we emulate.
But if we set the vmx-visible limit to 0xffff, we can use vm86 to virtualize
real mode; if an access overruns the segment limit, the guest will #GP, which
we will trap and forward to the emulator.  This results in significantly
faster execution, and less risk of hitting an unemulated instruction.

If the limit is less than 0xffff, we retain the existing behaviour.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Real mode is always entered from protected mode with dpl=0.  Since
the dpl doesn't affect execution, and we already override it to 3
in the vmcs (as vmx requires), we can allow execution in that state.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Real processors don't change segment limits and attributes while in
real mode.  Mimic that behaviour.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Instead of using struct kvm_save_segment, use struct kvm_segment, which is what
the other APIs use.  This leads to some simplification.

We replace save_rmode_seg() with a call to vmx_save_segment().  Since this depends
on rmode.vm86_active, we move the call to before setting the flag.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

fix_pmode_dataseg() looks up S in ->base instead of ->ar_bytes.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Commit b246dd5d ("KVM: VMX: Fix KVM_SET_SREGS with big real mode
segments") moved fix_rmode_seg() to vmx_set_segment(), so that it is
applied not just on transitions to real mode, but also on KVM_SET_SREGS
(migration).  However fix_rmode_seg() not only munges the vmcs segments,
it also sets up the save area for us to restore when returning to
protected mode or to return in vmx_get_segment().

Move saving the segment into a new function, save_rmode_seg(), and
call it just during the transition.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Instead of populating the entire register file, read in registers
as they are accessed, and write back only the modified ones.  This
saves a VMREAD and VMWRITE on Intel (for rsp, since it is not usually
used during emulation), and a two 128-byte copies for the registers.
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

The build error was caused by that builtin functions are calling
the functions implemented in modules. This error was introduced by
commit 4d8b81ab ("KVM: introduce readonly memslot").

The patch fixes the build error by moving function __gfn_to_hva_memslot()
from kvm_main.c to kvm_host.h and making that "inline" so that the
builtin function (kvmppc_h_enter) can use that.
Acked-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

This reverts commit b1acf1bb.

Something went horribly wrong when I did savedefconfig, not sure what,
but what's in there is busted so let's revert it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

For certain speculative events on Power7, 'perf stat' reports far higher
event count than 'perf record' for the same event.

As described in following commit, a performance monitor exception is raised
even when the the performance events are rolled back.

        commit 0837e324
        Author: Anton Blanchard <anton@samba.org>
        Date:   Wed Mar 9 14:38:42 2011 +1100

perf_event_interrupt() records an event only when an overflow occurs. But
this check for overflow is a simple 'if (val < 0)'.

Because the events are rolled back, this check for overflow fails and the
event is not recorded. perf_event_interrupt() later uses pmc_overflow() to
detect the overflow and resets the counters and the events are lost completely.

To properly detect the overflow of rolled back events, use pmc_overflow()
even when recording events.

To reproduce:
        $ cat strcpy.c
        #include <stdio.h>
        #include <string.h>
        main()
        {
                char buf[256];

                alarm(5);
                while(1)
                        strcpy(buf, "string1");
        }

        $ perf record -e r20014 ./strcpy
        $ perf report -n > report.1
        $ perf stat -e r20014 > report.2
        # Compare report.1 and report.2
Reported-by: NMaynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: NSukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The enhanced prefetch hint patches corrupt the condition register
that was used to check if we are in interrupt. Fix this by using cr1.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

"powerpc: Use enhanced touch instructions in POWER7
copy_to_user/copy_from_user" was applied twice. Remove one.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Directly comparing current->personality against PER_LINUX32 doesn't work
in cases when any of the personality flags stored in the top three bytes
are used.

Directly forcefully setting personality to PER_LINUX32 or PER_LINUX
discards any flags stored in the top three bytes

Use personality() macro to compare only PER_MASK bytes and make sure that
we are setting only the bits that should be set, instead of overwriting
the whole value.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Checking for device mask to cover the whole IOMMU table is too strict.
IOMMU allocators should handle mask constraint properly for each
allocation.

The patch enables to use old AirPort Extreme cards on PowerMacs with
more than 1GB of memory; without the patch the driver init fails with:

  b43-pci-bridge 0001:01:01.0: Warning: IOMMU window too big for device mask
  b43-pci-bridge 0001:01:01.0: mask: 0x3fffffff, table end: 0x80000000
  b43-phy0 ERROR: The machine/kernel does not support the required 30-bit DMA mask
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

For powerpc BooKE and e200, singlestep is handled on the critical/dbg
exception stack. This causes current_thread_info() to fail for kgdb
internal, so previously We work around this issue by copying
the thread_info from the kernel stack before calling kgdb_handle_exception,
and copying it back afterwards.

But actually we don't do this properly. We should backup current_thread_info
then restore that when exit.
Signed-off-by: NTiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We need to skip a breakpoint exception when it occurs after
a breakpoint has already been removed.
Signed-off-by: NTiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The kgdb_single_step flag has the possibility to indefinitely
hang the system on an SMP system.

The x86 arch have the same problem, and that problem was fixed by
commit 8097551d(kgdb,x86: do not set kgdb_single_step
on x86). This patch does the same behaviors as x86's patch.
Signed-off-by: NDongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Add several #includes that mpic_msgr relies on being pulled implicitly,
which only happens on certain configs.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Cc: Meador Inge <meador_inge@mentor.com>
Cc: Jia Hongtao <B38951@freescale.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Currently if you are doing a global perf recording with hardware
breakpoints (ie perf record -e mem:0xdeadbeef -a), you can oops with:

  Faulting instruction address: 0xc000000000738890
  cpu 0xc: Vector: 300 (Data Access) at [c0000003f76af8d0]
      pc: c000000000738890: .hw_breakpoint_handler+0xa0/0x1e0
      lr: c000000000738830: .hw_breakpoint_handler+0x40/0x1e0
      sp: c0000003f76afb50
     msr: 8000000000001032
     dar: 6f0
   dsisr: 42000000
    current = 0xc0000003f765ac00
    paca    = 0xc00000000f262a00   softe: 0        irq_happened: 0x01
    pid   = 6810, comm = loop-read
  enter ? for help
  [c0000003f76afbe0] c00000000073cd04 .notifier_call_chain.isra.0+0x84/0xe0
  [c0000003f76afc80] c00000000073cdbc .notify_die+0x3c/0x60
  [c0000003f76afd20] c0000000000139f0 .do_dabr+0x40/0xf0
  [c0000003f76afe30] c000000000005a9c handle_dabr_fault+0x14/0x48
  --- Exception: 300 (Data Access) at 0000000010000480
  SP (ff8679e0) is in userspace

This is because we don't check to see if the break point is associated
with task before we deference the task_struct pointer.

This changes the update to use current.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

There are a few whitespace goolies in xmon.c, some of them appear to
be my fault. Fix them all in one go.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Since the printk internals were reworked the xmon 'dl' command which
dumps the content of __log_buf has stopped working.

It is now a structured buffer, so just dumping it doesn't really work.

Use the helpers added for kgdb to print out the content.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Yocto (Built by Poky 7.0) 1.2 root filesystems fail to boot,
at least over nfs, with:

Failed to mount /dev: No such device

Configuring DEVTMPFS fixes it.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

run make savedefconfig on fsl defconfigs.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Using 'select' in Kconfig is hard, a platform cannot just
enable a driver without also making sure that its subsystem
is there. Also, there is no actual code dependency between
the platform and the gpio leds driver.

Without this patch, building without LEDS_CLASS esults in:

drivers/built-in.o: In function `create_gpio_led.part.2':
governor_userspace.c:(.devinit.text+0x5a58): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `gpio_led_remove':
governor_userspace.c:(.devexit.text+0x6b8): undefined reference to `led_classdev_unregister'

This reverts 8733f53c "ARM: ux500: Kconfig: Compile in leds-gpio
support for Snowball" that introduced the regression and did not
provide a helpful explanation.

In order to leave the GPIO LED code still present in normal
builds, this also enables the symbol in u8500_defconfig, in addition
to the other LED drivers that are already selected there.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>

The head-v7.S contains a call to the generic cpu_suspend function,
which is only available when selected by the i.MX6 code. As
pointed out by Shawn Guo, i.MX5 does not actually use any
functions defined in head-v7.S. It is also needed only for
the i.MX6 power management code and for the SMP code, so
we can restrict building this file to situations in which
at least one of those two is present.

Finally, other platforms with a similar file call it headsmp.S,
so we can rename it to the same for consistency.

Without this patch, building imx5 standalone results in:

arch/arm/mach-imx/built-in.o: In function `v7_cpu_resume':
arch/arm/mach-imx/head-v7.S:104: undefined reference to `cpu_resume'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Eric Miao <eric.miao@linaro.org>
Cc: stable@vger.kernel.org