Presently this is special-cased for early initialization. While there are
situations where these static early initializations are still necessary,
with minor changes it is possible to use this for the regular ioremap
implementation as well. This allows us to kill off the special-casing for
the remap completely and to start tidying up all of the SH-5
special-casing in drivers.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

sh64 is still using this, so re-enable it temporarily while SH-5 gets
converted to use the generic code.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Presently shm_align_mask is only looked at for the bottom up case, but we
still want this for proper colouring constraints in the topdown case.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There still seems to be some stack corruption to sort out here, so flag
this as BROKEN until this issue is sorted out.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The old arch/sh/kernel/timers/ directly will be going away completely
once the rest of the TMU users are migrated, so move the dummy broadcast
driver up a level in preparation.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Now that the stragglers (MTU2/CMT/etc.) have been rewritten and we are
selecting both GENERIC_TIME and GENERIC_CLOCKEVENTS, the get_offset()
timer op is completely unused. As a result, we are now able to kill off
the ARCH_USES_GETTIMEOFFSET references.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Now that the rest of the timers that didn't support clockevents have been
rewritten, both of these can be enabled by default.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

All of the SH timers use a roughly identical structure for platform data,
which presently is broken out for each block. Consolidate all of these
definitions, as there is no reason for them to be broken out in the first
place.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds TMU platform data for sh7722. Only clockevent
mode is enabled for now, clocksource requires this patch:
"clocksource: setup mult_orig in clocksource_enable()"
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds a TMU driver for the SuperH architecture.

The TMU driver is a platform driver with early platform
support to allow using a TMU channel as clockevent or
clocksource during system bootup or later.

Clocksource or clockevent can be selected.
Both periodic and oneshot clockevents are supported.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch removes the old MTU2 driver (CONFIG_SH_MTU2/timer-mtu2.c)

As replacement, select the sh_cmt driver with CONFIG_SH_TIMER_MTU2
and configure timer channel using platform data.

If multiple MTU channels are enabled using platform data, use the
earlytimer parameter on the kernel command line to select channel.
For instance, use "earlytimer=sh_mtu2.0" to select the first channel.

To verify which timer is being used, look at printouts or the timer
irq count in /proc/interrupts.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds MTU2 platform data for the following cpus:
 - sh7201 (3/5 channels)
 - sh7203/sh7263 (2/4 channels)
 - sh7206 (3/5 channels)
 - MXG (3/5 channels)
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds a MTU2 driver for the SuperH architecture.

The MTU2 driver is a platform driver with early platform
support to allow using a MTU2 channel as only clockevent
during system bootup.

Clocksource on sh2a is currently unsupported due to code
generation issues with 64-bit math, so at this point only
periodic clockevent support is in place.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert sh to use GENERIC_TIME via the arch_getoffset() infrastructure.
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Impact: cleanup

Convert the last remaining users to struct irq_chip and remove the
define.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Impact: cleanup

convert the last remaining users to no_irq_chip
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch removes the old CMT driver (CONFIG_SH_CMT/timer-cmt.c)

As replacement, select the sh_cmt driver with CONFIG_SH_TIMER_CMT
and configure timer channel using platform data.

If multiple CMT channels are enabled using platform data, use the
earlytimer parameter on the kernel command line to select channel.
For instance, use "earlytimer=sh_cmt.0" to select the first channel.

To verify which timer is being used, look at printouts or the timer
irq count in /proc/interrupts.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds 16-bit cmt platform data for the following cpus:
 - sh7619 (2 channels)
 - sh7203/sh7263 (2 channels)
 - sh7206 (2 channels)
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

All 32-bit SuperH processors currently go through __ioremap_mode()
and check for IO_TRAPPED and directly mapped segments. With this
patch we simplify the MMU less case with a pass through version of
 __ioremap_mode() which just returns the physical address.

The effects of this is change are:
 - fix non-MMU ioremap() of high address hardware blocks (sh7203 CMT)
 - make sure IO_TRAPPED is not selected
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fix this:

  arch/m68k/kernel/sun3-head.S: Assembler messages:
  arch/m68k/kernel/sun3-head.S:32: Error: Unknown operator -- statement `__head' ignored

Introduced by commit 6f335cab ("m68k:
convert to use __HEAD and HEAD_TEXT macros."), which started using
__HEAD without adding the appropriate include.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit edada399 broke the build on 64-bit powerpc because it moved the
__ftr_alt_* sections of a file away from the .text section, causing
link failures due to relative conditional branch targets being too far
away from the branch instructions.  This happens on pretty much all
64-bit powerpc configs.

This change reverts commit edada399 while preserving the update from
the *.refok sections to .ref.text that has happened since.
Signed-off-by: NTim Abbott <tabbott@mit.edu>
Requested-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The device registration was accidentally omitted, add it back in. Do some
basic device probing as well, so this doesn't show up for platforms that
tie in to the RTC interface properly.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch moves the SuperH timer setup code from time_init()
to late_time_init(). Good things about this change:
 - interrupts: they are enabled at late_time_init()
 - mm: regular kmalloc() can be used at late_time_init()

Together with moving to late_time_init() this patch changes
the sh_cmt driver to always allocate with kmalloc(). This
simplifies the code a bit and also fixes section mismatches.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

A non-SMP version of smp_send_stop() is now included in smp.h.
Remove the unneeded definition in the PS3 smp.c.

Fixes build errors like these when CONFIG_SMP=n:

  arch/powerpc/platforms/ps3/setup.c:49: error: redefinition of 'smp_send_stop'
  include/linux/smp.h:125: error: previous definition of 'smp_send_stop' was here
Reported-by: NSubrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Currently PPC_CELL_NATIVE selects PPC_OF_PLATFORM_PCI, but does not
select PCI. This can lead to a config with the former and the latter
disabled, which does not build.

To fix this PPC_CELL_NATIVE should select PCI. However, that would
force PCI on for QPACE, which also selects PPC_CELL_NATIVE. So
instead move the select of PPC_OF_PLATFORM_PCI and PCI under both
IBM_CELL_BLADE and CELLEB.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

On ppc64 we implemented elf_read_implies_exec() for 32-bit binaries
because old toolchains had bugs where they didn't mark program
segments executable that needed to be.  For some reason we didn't do
this on ppc32 builds.  This hadn't been an issue until commit 8d30c14c
("powerpc/mm: Rework I$/D$ coherency (v3)"), which had as a side
effect that we are now enforcing execute permissions to some extent on
32-bit 4xx and Book E processors.

This fixes it by defining elf_read_implies_exec on 32-bit to turn on
the read-implies-exec behaviour on programs that are sufficiently old
that they don't have a PT_GNU_STACK program header.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The section .text.init.refok is deprecated and __REF (.ref.text)
should be used in assembly files instead.  This patch cleans up a few
uses of .text.init.refok in the sparc architecture.

Also fix a reference to .text.init in a comment that wasn't updated to
.init.text.
Signed-off-by: NTim Abbott <tabbott@mit.edu>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The sh architecture has some code in the .text.init section, but it
does not reference that section in its linker scripts.

This change moves this code from the .text.init section to the
.init.text section, which is presumably where it belongs.
Signed-off-by: NTim Abbott <tabbott@mit.edu>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The section .text.init.refok is deprecated and __REF (.ref.text)
should be used in assembly files instead.  This patch cleans up a few
uses of .text.init.refok in the powerpc architecture.
Signed-off-by: NTim Abbott <tabbott@mit.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Rather than adding .ref.text to the powerpc linker script so that we
can use __REF on the powerpc architecture, it seems simpler to switch
to using the generic TEXT_TEXT macro.
Signed-off-by: NTim Abbott <tabbott@mit.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

arm is placing some code in the .text.init section, but it does not
reference that section in its linker scripts.

This change moves this code from the .text.init section to the
.init.text section, which is presumably where it belongs.
Signed-off-by: NTim Abbott <tabbott@mit.edu>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

FRV is placing some code in the .text.init section but does not reference that
section in its linker scripts.

This change moves this code from the .text.init section to the .init.text
section, which is presumably where it belongs.
Signed-off-by: NTim Abbott <tabbott@mit.edu>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It seems nothing has included the frv asm/init.h header for some time, and its
actual contents are out of date with include/linux/init.h.  So just delete it.
Signed-off-by: NTim Abbott <tabbott@mit.edu>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The 'device_type = "soc";' line *is* needed in the DTS for get_immrbase()
to return the correct address.
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Stop gcc from generating uninitialised variable warnings after BUG().
The problem is that FRV's call into its gdbstub appears to return (if
the function is marked noreturn, then the compiler is under no
obligation to pass it a return address, and so GDB won't know where the
bug happened).

To get around this, we make the do...while wrapper in _debug_bug_trap()
an endless loop from which there's no escape.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Wire up new system calls for the FRV arch (preadv and pwritev).
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The RTS7751R2D_1 boards only support 1MB of socket-mounted MBM29F040
flash, which we just leave alone as it's not terribly interesting.

This adds support for the s29gl256p on the r2d+ boards that makes a bit
more sense to expose to the user.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds rtc-generic support for SUPERH32.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

syscall_nr is presently defined as unsigned in the SH-5 pt_regs,
while the syscall restarting code wants it to be signed. Fix this
up, and bring it in line with the other SH parts.
Reported-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>