Skyhawk-R FW supports TX-rate setting only as a % value of the link
speed, set via the SET_PROFILE_CONFIG cmd.

This patch makes the necessary changes to the FW cmd descriptors to support
the above change and also introduces checks in be_set_vf_tx_rate() to allow
only discrete values (that map to % of the link-speed).
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set mc-promisc (multicast promiscuous) mode on an interface, only if it is
*not already* in that mode.

Also removed logs that report interface being set to multicast
promiscous mode. In an earlier comment on the netdev list such log messages
were deemed unnecessary as this behaviour is common across most of the
ethernet drivers.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
  to have a bandwidth of at least this value.
  max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
  of up to this value.

o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
  which takes 4 arguments:
  netdev, VF number, min_tx_rate, max_tx_rate

o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.

o Drivers that currently implement ndo_set_vf_tx_rate should now call
  ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
  greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
  implemented by driver.

o If user enters only one of either min_tx_rate or max_tx_rate, then,
  userland should read back the other value from driver and set both
  for IFLA_VF_RATE.
  Drivers that have not yet implemented IFLA_VF_RATE should always
  return min_tx_rate as 0 when read from ip tool.

o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
  IFLA_VF_RATE should override.

o Idea is to have consistent display of rate values to user.

o Usage example: -

  ./ip link set p4p1 vf 0 rate 900

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 600 rate 300

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some BE3 FW versions, after a HW reset, interrupts will remain disabled
for each function. So, explicitly enable the interrupts in the eeh_resume
handler, else after an eeh recovery interrupts wouldn't work.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: get rid of SET_ETHTOOL_OPS

Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.

Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
-       SET_ETHTOOL_OPS(dev, ops);
+       dev->ethtool_ops = ops;

Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: NDave Miller <davem@davemloft.net>
Signed-off-by: NWilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For putting interface into vlan promiscuous mode, we use be_cmd_rx_filter()
and not be_cmd_vlan_config(). So remove the "promiscuous" argument from
be_cmd_vlan_config().
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts the vlan u8[] used to track vlan-id
membership to a bit-map as it reduces memory usage.
Signed-off-by: NRavikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a funtion definition or a function call spans more than one
line, ensure that the first argument on the subsequent lines is
aligned to the first column after the opening paranthesis of the
function call.

Also remove unnecessary line wrap.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This be2net patch implements the get/set_rxfh() ethtool hooks.
RSS_CONFIG device command is invoked to set hashkey and indirection table.
It also uses an initial random value for RSS hash key instead of a
hard-coded value as hard-coded values for a hash-key are usually
considered a security risk.
Signed-off-by: NVenkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the EEH error recovery path, when a permanent failure occurs,
we clean up adapter structure (i.e. destroy queues etc) by calling
be_clear() and return PCI_ERS_RESULT_DISCONNECT.
After this the stack tries to remove device from bus and calls
be_remove() which invokes netdev_unregister()->be_close().
be_close() operating on destroyed queues results in a
NULL dereference.

This patch fixes this problem by introducing a flag to keep track
of the setup state.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

be_close() currently waits for a max of 200ms to receive all pending
TX compls. This timeout value was roughly calculated based on 10G
transmission speeds and the TX queue depth. This timeout may not be
enough when the link is operating at lower speeds or in multi-channel/SR-IOV
configs with TX-rate limiting setting.

It is hard to calculate a "proper timeout value" that works in all
configurations.  This patch solves this problem by continuing to reap
TX completions till the HW is completely silent for a period of 10ms or
a HW error is detected.

v2: implements the new scheme (as suggested by David Laight) instead of
just waiting longer than 200ms for reaping all completions.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a CONFIG_BE2NET_VXLAN define to control be2net's build
dependency on the VXLAN driver.

Without this fix, the kernel build fails when VxLAN driver is
selected to be built as a module while be2net is built-in.

fixes: c9c47142 ("be2net: csum, tso and rss steering offload support for VxLAN")
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch mainly implements the add/del_vxlan_port() methods by invoking
the needed FW cmds for supporting VxLAN offloads for Skyhawk-R.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the FW cmds needed for VxLAN offloads
on Skyhawk-R:
1) The VxLAN UDP port needs to be configured via the port-desc of
   SET_PROFILE_CONFIG_v1 cmd.
   This patch re-factors the be_set_profile_config() code (used so far
   only for setting VF QoS) to be used to set any type of descriptor.
2) The MANAGE_IFACE_FILTERS cmds is needed to convert a normal interface
   into a tunnel interface. This allows for RSS to work even on the inner
   TCP/UDP headers of VxLAN traffic.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the bh safe variant with the hard irq safe variant.

We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.

Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace free_skb with dev_kfree_skb_any in be_tx_compl_process as
which can be called in hard irq by netpoll, softirq context
by normal napi polling, and in normal sleepable context
by the network device close method.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a VLAN is added by user, adapter->vlans_added is incremented.
But if the VLAN is already programmed in HW, driver ends up
incrementing the counter wrongly.

Increment the counter only if VLAN is not already programmed in the HW.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the driver creates only a single TXQ on any BE3-R multi-channel
interface.
This patch changes this and creates multiple TXQs on RSS-capable multi-channel
BE3-R interfaces. This change helps improve the TX pps performance on the
affected interface.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The allocation size must be be_max_uc() and not "be_max_uc() + 1"
Signed-off-by: NRavikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to control VF's link state by implementing the
ndo_set_vf_link_state() hook.
Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use GET_PROFILE_CONFIG_V1 cmd even for BE3-R (it's already used for
Lancer-R and Skyhawk-R), to query max-vfs value supported by the FW.
This is needed as on some configs, the value exported in the PCI-config
space is not accurate.
Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver currently maps a page for DMA, divides the page into multiple
frags and posts them to the HW. It un-maps the page after data is received
on all the frags of the page. This scheme doesn't work when bounce buffers
are used for DMA (swiotlb=force kernel param).

This patch fixes this problem by calling dma_sync_single_for_cpu() for each
frag (excepting the last one) so that the data is copied from the bounce
buffers. The page is un-mapped only when DMA finishes on the last frag of
the page.
(Thanks Ben H. for suggesting the dma_sync API!)

This patch also renames the "last_page_user" field of be_rx_page_info{}
struct to "last_frag" to improve readability of the fixed code.
Reported-by: NLi Fengmao <li.fengmao@zte.com.cn>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of TX workarounds in be_xmit_workarounds() routine
are not applicable (and result in HW errors) to Skyhawk-R chip.
Isolate BE3-R/Lancer specific workarounds to a separate routine.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb_padto(), skb_share_check() and __vlan_put_tag() routines free
skb when they return an error. This patch fixes be_xmit_workarounds()
to not free skb again in such cases.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should clear promiscuous bits in adapter->flags while disabling promiscuous
mode. Else we will not put interface back into VLAN promisc mode if the vlans
already added exceeds the maximum limit.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For disabling transparent tagging issue SET_HSW_CONFIG with pvid_valid=1
and pvid=0xFFFF and not with the default pvid as this case would fail in Lancer.
Hence removing the get_hsw_config call from be_vf_setup() as it's
only use of getting default pvid is no longer needed.

Also do proper housekeeping only if the FW command succeeds.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Acked-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently multi-channel configuration is read via the QUERY_FW_CONFIG cmd.
This method has been deprecated by the Skyhawk-R FW. Instead,
GET_PROFILE_CONFIG::port-desc must be used to query this configuration.

This patch also:
a) introduces a few macros to identify certain categories of multi-channel
configs
2) re-factors the be_cmd_set_profile_config() code to be able to read any kind
of desc (and not just the nic-desc.)
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch logs a kernel message when a HW error(SLIPORT_ERROR in Lancer and UE
in BEx/Skyhawk) is detected. The log message for BE3 was missing earlier.
This patch also refactors the code by segregating error-detection and reporting
code for Lancer and BEx/SH.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current logic to put interface into VLAN Promiscous mode is not correct.
We should increment "adapter->vlans_added" before calling be_vid_config().
Also removed some unwanted log messages.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver does not check value returned by dma_map_page. The patch
fixes this.

v2: Removed the bugfix for non-bug ;-) (thanks Sathya)
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NSathya Perla <Sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleans-up wake-on-lan code in the following ways:
1) Removes some driver hacks in be_cmd_get_acpi_wol_cap() that were based
on incorrect assumptions.
2) Uses the adapter->wol_en and wol_cap variables for checking if WoL
is supported and enabled on an interface instead of referring to the
exclusion list via the macro be_is_wol_supported()
Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The use of NTKW_MAC_QUERY cmd has been deprecated for Skyhawk-R.
Replace the last remaining usage in be_vfs_mac_query() routine.
Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead, use the tail of the RXQ to pick the associated RXQ entry

This fix is required in preparation for supporting RXQ lengths greater than 1K.
For such queues, the frag index in the RX-compl entry is not valid as it is only a 10 bit entry not capable of addressing RXQs longer than 1K.
Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An earlier commit (f25b119c "Fix error messages while driver load for VFs")
incorrectly set the adapter->cmd_privileges value for VFs (in a
multi-channel config) to MAX_PRIVILEGES. This causes FW cmd failures
and avoidable error logs when certian cmds are issued by a VF.
Also, move the multi-channel hack to be_cmds.c inside
be_cmd_get_fn_privileges() routine.

Fixes: f25b119c "Fix error messages while driver load for VFs"
Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An ndo_set_mac_addr() call may be issued for a mac-addr that is already
active on an interface. If so, silently ignore the request. Sending such
a request to the FW, causes a "mac collision" error. The error is harmless
but is avoidable noise in the kernel log.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Skyhawk-R FW does not support SET/GET_EXT_FAT_CAPABILITIES cmds via which
FW logging level can be controlled. Also, the hack used in BE3 to control
FW logging level via the ethtool interface is not needed in Skyhawk-R.

This patch also cleans up this code by moving be_set/get_fw_log_level()
routines to be_cmds.c where they belong.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>

remove new line
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver wrongly assumes 16 EQs/vectors are available for each BE3 PF.
When SR-IOV is enabled, a BE3 PF can support only a max of 8 EQs.
Signed-off-by: NSuresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>