Change the value of TX_CMD_SEC_KEY_FROM_TABLE flag
in TX_CMD security flags to accommodate a FW API change.

Bump min API for 9000 series devices to 30 to keep the driver aligned
aligned the FW.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Seems like HW is reversing addr3 in the MAC header of de-aggregated
AMSDU. Reverse it back.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This flag is used for mac80211 reordering. As we do reordering
ourselves, turning it on is misleading and pointless.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Not only that this write is not needed (as FW does this
itself), on newer HW this register is write protected
so trying to write there will cause problems.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In TVQM firmware returns the value of the queue ID and code
should accept it.
The TX queue config API was changed. Move to new API.
This has to be done in parallel in mvm and pcie.
Do not move yet to 512 queues since there are some opens
with enabling it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In TVQM mode the TX responses were changed to include
queue number since legacy TX queue number retrieval cannot
be scaled up to 512 queues.
Support this change.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In TVQM mode the queue ID is assigned after enablement.
Get rid of assuming pre-defined TX queue ID in functions
that will be used by TVQM allocation path.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The "invalid" label was a bit ugly and unnecessary.  Remove it.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Change queue allocation to be dynamic. On transport init only
the command queue is being allocated. Other queues are allocated
on demand.
This is due to the huge amount of queues we will soon enable (512)
and as a preparation for TX Virtual Queue Manager feature (TVQM),
where firmware will assign the actual queue number on demand.
This includes also allocation of the byte count table per queue
and not as a contiguous chunk of memory.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This function is basically the same as gen1, except for clean
ups of old devices configuration that are never used in a000
configuration.
It will also help with refactoring rf_kill later on.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In a000 transport we will allocate queues dynamically.
Right now queue are allocated as one big chunk of memory
and accessed as such.
The dynamic allocation of the queues will require accessing
the queues as pointers.
In order to keep simplicity of pre-a000 tx queues handling,
keep allocating and freeing the memory in the same style,
but move to access the queues in the various functions as
individual pointers.
Dynamic allocation for the a000 devices will be in a separate
patch.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

New transport will be used only by op modes that supports
buffer station offload - hence those will never be called.
Clean it up.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In a000 devices we have 16 bytes for the TFD index and 16 for the
queue, in order to support 512 queues.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Code is basically the same, with a cleanups of old narrow host
command, ampg workarounds, some cosmetic stuff, and usage of
TFH functions when accessing TFD queues.
This enables also the cleanup of iwl_pcie_tfd_set_tb() since
now it won't be called anywhere in the a000 data path
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Move to use the correct structure.
Remove code referring to old command.
Update DMA locations.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Cleanup code that is irrelevant for a000 devices.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

By moving all the code that depends on the new API
we avoid unnecessary indentation in the code.
Signed-off-by: NMordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Newer firmware versions will be able to handle all the
WMM-PS flows internally when we act as a GO. The firwmare
relies on the fact that the drivers puts frames for
different peers in different queues (DQA) to achieve this.
The driver will not be aware of the power state of the peers
anymore.

Tell the firmware about the WMM-PS parameters of earch peer
that connects to us so that it can know what are the
trigger-enabled ACs, the delivery-enableds ACs and the
Service Period length.

This API change is backward compatible since older firmware
versions will simply ignore the newly added values.

Since we don't support ieee80211 TSPECs for now, just copy
the trigger-enabled ACs to the delivery enabled ones.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There are several occasions where a scan of the same type is requested
concurrently, so logging every time this happens is just noisy and
unnecessary.  Remove the logging for these cases.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This is just a copy-paste in order to make changes tracking
easier.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For a000 FW moved to 15 as management TID.
The change for us is fairly local - translate old TID to 15
when enabling and disabling a queue, and make sure to cover
it also on TX responses.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

a000 devices queue management is going to change significantly.
We will have 512 queues. Those queues will be assigned number
by the firmware and not by the driver.

In addition, due to SN offload having TX queue shared between TIDs
is impossible

Also, the ADD_STA command no longer updates queues status.
The only point of changing queue in the SCD queue config API.

From driver perspective we have here a new design:

Queue sharing and inactivity checks are disabled.

Once this is done, the only paths that call scd_queue_cfg command
are paths that alloc and release TX queues - which will make future
accommodation to queue number assignment by FW easier.
Since allocating 512 queues statically is not advisable, transport
will allocate the queue on demand, fill the command with DRAM data
and send it. This is reflected in the new transport API.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In a000 devices the TX handling is different in a few ways:
* Queues are allocated dynamically
* DQA is enabled by default
* Driver shouldn't access TFH registers - ucode configures it
  all in SCD_QUEUE_CFG command

Support all this in a new API with op mode, where op mode sends
the command, transport will allocate the queue dynamically, fill
in DMA properties, send the command to FW and get the ID back.
Current implementation only sets the new transport API and fills
the DMA properties.
Future patches will complete the other parts.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support the new TX command API for a000 devices.
Command is a very slim version of current TX command.
Generalize iwl_mvm_tx_mpdu to get rid of TX command dependencies.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Dynamic SAR allows changing TX power limits at runtime to comply with
SAR regulations on multiple form factors (e.g. tablet vs. clamshell
mode).  To support this, a new table was added to ACPI, which is
called Extended Wireless Regulatory Descriptor (EWRD).  This table
allows OEMs to define different TX power profiles for each form-factor
or usage mode.

Read this new table and store it in our SAR profiles table, in
preparation for Dynamic SAR support.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For dynamic SAR, we will need to select the current profile from
different places.  In preparation for that, spin the profile selection
code out of iwl_mvm_sar_init().
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We are adding support for dynamic TX power tables for SAR (specific
absorption rate) compliance.  Currently, we only support a single
(static) TX power table, which is read from ACPI, and use it
statically.

To prepare for more tables that can be switched dynamically, refactor
the SAR init flow to allow reusage and add the current static table as
a single entry in an array of tables.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Firmware isn't configuring multi RX queue hardware yet in
the self init mode.
Disable it for now until we have an API that enables it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

API will be the same regardless of FW compilation.
CDB related values will be filled in only for CDB.
Cahneg code and names accordingly.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In a000 devices we will support up to 32 stations.
The max station define is used also for invalid station marking
which makes finding usages of actual maximum station pretty hard
to sort through - change it to be a different define in order
to make future changes easier.
Use also ARRAY_SIZE intead of define when possible.
Do not move yet to 32 stations until firmware do it though.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

iwl_has_secure_boot() isn't getting called anywhere. Clean it up.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently aux & broadcast queues are added before calling add
station, which results with a SCD_QUEUE_CFG command sent with
a station id unknown yet to fw.
While this works for pre-a000 firmware, the a000 fw requires
the order to be reversed.
The reason the change is only for a000 devices and not for
previous devices is that we cannot reverse the order since
the tfd_queue_mask containing the aux queue will cause FW to
assert on adding a queue mask with a queue that is not enabled.
This is not a problem in a000 fw since the tfd_queue_mask was
removed from the add sta API.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Addresses were changed for a000 devices.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

As preparation for a000 different queue management, separate
mapping of queues from actual enablement.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Now that transport inits the paging in the context info -
remove the call in mvm.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Context information structure is going to be used in a000
devices for firmware self init.

The self init includes firmware self loading from DRAM by
ROM.
This means the TFH relevant firmware loading can be cleaned up.

The firmware loading includes the paging memory as well, so op
mode can stop initializing the paging and sending the DRAM_BLOCK_CMD.

Firmware is doing RFH, TFH and SCD configuration, while driver
only fills the required configurations and addresses in the
context information structure.

The only remaining access to RFH is the write pointer, which
is updated upon alive interrupt after FW configured the RFH.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

a000 devices are going to have a lot of flows simplified
and changed: init flow, RX, TX, and more.
This, combined with the fact that code is already very
complicated due to backward compatibility - introduce
a split that will enable to introduce simplified version
of functions.
Shared ops are moved to a macro, while functions that will
be updated in the next patches are defined twice for now.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We don't need this parameter anymore, since we always pass 0 anyway.
Remove it from the structure and from all the relevant functions.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In case of a MFUART assert, get a notification from the fw
that consists of the assert id and debug data.

The notification may be divided to multiple chunks, depending
on the size of the debug data sent to the driver, which would
be up to 1KB.

Get the notification, and if the debug info flag is enabled,
print the debug data to the dmesg.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>