The new short message format is used on the new BCM57454 VFs.  Each
firmware message is a fixed 16-byte message sent using the standard
firmware communication channel.  The short message has a DMA address
pointing to the legacy long firmware message.
Signed-off-by: NDeepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change restricts the PF in multi-host mode from setting any port
level PHY configuration.  The settings are controlled by firmware in
Multi-Host mode.
Signed-off-by: NDeepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for 100G link speed reporting for Broadcom BCM57454
ASIC in ethtool command.
Signed-off-by: NDeepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: NRay Jui <ray.jui@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mac loopback self test operates in polling mode.  To support that,
we need to add functions to open and close the NIC half way.  The half
open mode allows the rings to operate without IRQ and NAPI.  We
use the XDP transmit function to send the loopback packet.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the basic infrastructure and only firmware tests initially.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And add functions to set and free magic packet filter.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add code to driver probe function to check if the device is WoL capable
and if Magic packet WoL filter is currently set.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These files all use functions declared in interrupt.h, but currently rely
on implicit inclusion of this file (via netns/xfrm.h).

That won't work anymore when the flow cache is removed so include that
header where needed.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set DCB_CAP_DCBX_HOST capability flag only if the firmware LLDP agent
is not running.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Print FEC (Forward Error Correction) autoneg and encoding settings during
link up.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new spec has NVRAM defragmentation support which will be used in
the next patch to improve ethtool flash operation.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add dedicated transmit function and transmit completion handler for
XDP.  The XDP transmit logic and completion logic are different than
regular TX ring.  The TX buffer is recycled back to the RX ring when
it completes.

v3: Improved the buffer recyling scheme for XDP_TX.

v2: Add trace_xdp_exception().
    Add dma_sync.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Tested-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add basic ndo_xdp support to setup and query program, configure the NIC
to run in rx page mode, and support XDP_PASS, XDP_DROP, XDP_ABORTED
actions only.

v3: Pass modified offset and length to stack for XDP_PASS.
    Remove Kconfig option.

v2: Added trace_xdp_exception()
    Added dma_syncs.
    Added XDP headroom support.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Tested-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

XDP_TX requires a different function to handle completion.  Add a
function pointer to handle tx completion logic.  Regular TX rings
will be assigned the current bnxt_tx_int() for the ->tx_int()
function pointer.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add logic for an extra set of TX rings for XDP.  If enabled, this
set of TX rings equals the number of RX rings and shares the same
IRQ as the RX ring set.  A new field bp->tx_nr_rings_xdp is added
to keep track of these TX XDP rings.  Adjust all other relevant functions
to handle bp->tx_nr_rings_xdp.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To support XDP_TX, we need to add a set of dedicated TX rings, each
associated with the NAPI of an RX ring.  To assign XDP rings and regular
rings in a flexible way, we add a bp->tx_ring_map[] array to do the
remapping.  The netdev txq index is stored in the new field txq_index
so that we can retrieve the netdev txq when handling TX completions.
In this patch, before we introduce XDP_TX, the mapping is 1:1.

v2: Fixed a bug in bnxt_tx_int().
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, bnxt_setup_tc() and bnxt_set_channels() have similar and
duplicated code to check and reserve rx and tx rings.  Add a new
function bnxt_reserve_rings() to centralize the logic.  This will
make it easier to add XDP_TX support which requires allocating a
new set of TX rings.

Also, the tx ring checking logic in bnxt_setup_msix() can be removed.
The rings have been reserved before hand.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the current code, we have separate rx_event and agg_event parameters
to keep track of rx and aggregation events.  Combine these events into
an u8 event mask with different bits defined for different events.  This
way, it is easier to expand the logic to include XDP tx events.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This mode is to support XDP.  In this mode, each rx ring is configured
with page sized buffers for linear placement of each packet.  MTU will be
restricted to what the page sized buffers can support.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert the global constants BNXT_RX_OFFSET and BNXT_RX_DMA_OFFSET to
device parameters.  This will make it easier to support XDP with
headroom support which requires different RX buffer offsets.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When driver is running in XDP mode, rx buffers are DMA mapped as
DMA_BIDIRECTIONAL.  Add a field so the code will map/unmap rx buffers
according to this field.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To support XDP_TX, we need the RX buffer's DMA address to transmit the
packet.  Convert the DMA address field to a permanent field in
bnxt_sw_rx_bd.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Minor refactoring of bnxt_rx_skb() so that it can easily be replaced by
a new function that handles packets in a single page.  Also, use a
function pointer bp->rx_skb_func() to switch to a new function when
we add the new mode in the next patch.

Add a new field data_ptr that points to the packet data in the
bnxt_sw_rx_bd structure.  The original data field is changed to void
pointer so that it can either hold the kmalloc'ed data or a page
pointer.

The last parameter of bnxt_rx_skb() which was the length parameter is
changed to include the payload offset of the packet in the upper 16 bit.
The offset is needed to support the rx page mode and is not used in
this existing function.

v3: Added a new data_ptr parameter to bp->rx_skb_func().  The caller
has the option to modify the starting address of the packet.  This
will be needed when XDP with headroom support is added.

v2: Changed the name of the last parameter to offset_and_len to make the
code more clear.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add LED blinking code to support ethtool -p on the PF.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code assumes that we will always have at least 2 rx rings, 1
will be used as an aggregation ring for TPA and jumbo page placements.
However, it is possible, especially on a VF, that there is only 1 rx
ring available.  In this scenario, the current code will fail to initialize.
To handle it, we need to properly set up only 1 ring without aggregation.
Set a new flag BNXT_FLAG_NO_AGG_RINGS for this condition and add logic to
set up the chip to place RX data linearly into a single buffer per packet.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to properly support TX rate limiting in SRIOV VF functions or
NPAR functions, firmware needs better control over tx ring allocations.
The new scheme requires the driver to reserve the number of tx rings
and to query to see if the requested number of tx rings is reserved.
The driver will use the new scheme when the firmware interface spec is
1.6.1 or newer.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The existing hardware RFS mode uses one hardware RSS context block
per ring just to calculate the RSS hash.  This is very wasteful and
prevents VF functions from using it.  The new hardware mode shares
the same hardware RSS context for RSS placement and RFS steering.
This allows VFs to enable RFS.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new vnic RSS capability will enhance NTUPLE support, to be added
in subsequent patches.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The advertising field is closely related to the auto_link_speeds field.
The former is the user setting while the latter is the firmware setting.
Both should be u16.  We should use the advertising field in
bnxt_get_link_ksettings because the auto_link_speeds field may not
be updated with the latest from the firmware yet.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use native NAPI polling instead.  The next patch will complete the work
by switching to use napi_complete_done()
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the network driver and RDMA driver operate on the same PCI function,
we need to create an interface to allow the RDMA driver to share resources
with the network driver.

1. Create a new bnxt_en_dev struct which will be returned by
bnxt_ulp_probe() upon success.  After that, all calls from the RDMA driver
to bnxt_en will pass a pointer to this struct.

2. This struct contains additional function pointers to register, request
msix, send fw messages, register for async events.

3. If the RDMA driver wants to enable RDMA on the function, it needs to
call the function pointer bnxt_register_device().  A ulp_ops structure
is passed for RCU protected upcalls from bnxt_en to the RDMA driver.

4. The RDMA driver can call firmware APIs using the bnxt_send_fw_msg()
function pointer.

5. 1 stats context is reserved when the RDMA driver registers.  MSIX
and completion rings are reserved when the RDMA driver calls
bnxt_request_msix() function pointer.

6. When the RDMA driver calls bnxt_unregister_device(), all RDMA resources
will be cleaned up.

v2: Fixed 2 uninitialized variable warnings.
Signed-off-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver register function with firmware consists of passing version
information and registering for async events.  To support the RDMA driver,
the async events that we need to register may change.  Separate the
driver register function into 2 parts so that we can just update the
async events for the RDMA driver.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the device supports RDMA, we'll setup network default rings so that
there are enough minimum resources for RDMA, if possible.  However, the
user can still increase network rings to the max if he wants.  The actual
RDMA resources won't be reserved until the RDMA driver registers.

v2: Fix compile warning when BNXT_CONFIG_SRIOV is not set.
Signed-off-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All available remaining completion rings not used by the PF should be
made available for the VFs so that there are enough rings in the VF to
support RDMA.  The earlier workaround code of capping the rings by the
statistics context is removed.

When SRIOV is disabled, call a new function bnxt_restore_pf_fw_resources()
to restore FW resources.  Later on we need to add some logic to account
for RDMA resources.
Signed-off-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that MSIX is enabled in bnxt_init_one(), resources may be allocated by
the RDMA driver before the network device is opened.  So we cannot do
function reset in bnxt_open() which will clear all the resources.

The proper place to do function reset now is in bnxt_init_one().
If we get AER, we'll do function reset as well.
Signed-off-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To better support the new RDMA driver, we need to move pci_enable_msix()
from bnxt_open() to bnxt_init_one().  This way, MSIX vectors are available
to the RDMA driver whether the network device is up or down.

Part of the existing bnxt_setup_int_mode() function is now refactored into
a new bnxt_init_int_mode().  bnxt_init_int_mode() is called during
bnxt_init_one() to enable MSIX.  The remaining logic in
bnxt_setup_int_mode() to map the IRQs to the completion rings is called
during bnxt_open().

v2: Fixed compile warning when CONFIG_BNXT_SRIOV is not set.
Signed-off-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By refactoring existing code into this new function.  The new function
will be used in subsequent patches.

v2: Fixed compile warning when CONFIG_BNXT_SRIOV is not set.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report PFC statistics to ethtool -S and DCBNL.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support only IEEE DCBX initially.  Add IEEE DCBNL ops and functions to
get and set the hardware DCBX parameters.  The DCB code is conditional on
Kconfig CONFIG_BNXT_DCB.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Latest interface has the latest DCB command structs.  Get and store the
max number of lossless TCs the hardware can support.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>