The state is already stored in ath9k_ops_config, so remove
the duplicate variable in ath_hw.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This routine always return true, checking for false
in the return value is invalid. Fix this.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean debug messages to use appropriate levels,
remove useless messages, and trim the number of
debug levels.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We get the valid chainmasks on HW attach, checking
it again during reset is redundant. This patch removes the check.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes unused HW capability flags and
HW operation variables, and a chainmask flag that
we don't use anywhere.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For chipsets supporting autosleep feature, there is no need to abort
Rx engine since they are capable of automatically going back to sleep
after receiving a packet.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Auto-depend on HW_RANDOM, rather than "select"ing it.
This way the user has the choice to enable or disable HWRNG support.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00link_reset_qual() is not declared in a header,
and is only internally used within rt2x00link.c.
It should be declared as static.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

pci_dev->irq and pci_name(pci_dev) access should be limited
to rt2x00pci only. This is more generic and allows a rt2x00 pci
driver to be controlled as PCI device but also as platform driver
(needed for rt2800pci SoC support).
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a locking problem which freezes the network core.

The deadlock goes as follows:
- ar9170_op_stop - is called
1. change the state to IDLE
2. > take the MUTEX <
3. cancel_SYNC all pending work, which means
    "block until a work_struct's callback has terminated"
=>  if filter_config_work was queued it tries to get the MUTEX,
       before checking the device state...
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR5K_PHY_PLL_40MHZ_5413 should not be ORed with AR5K_PHY_MODE_RAD_RF5112
for 5 GHz channels.

The incorrect PLL value breaks scanning in the countries where 5 GHz
channels are allowed.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Almost all drivers do not support user_claim, so remove it
completely and always report -EOPNOTSUPP to userspace. Since
userspace cannot really drive rfkill _anyway_ (due to the
odd restrictions imposed by the documentation) having this
code is just pointless.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware may insert up to 4 padding bytes after the lmac header,
but it does not amend the size of SPI data transfer.
Such packets has correct data size in header, thus referencing
past the end of allocated skb. Put extra 4 bytes to the end of the
received skb to compensate for this case.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Acked-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

3945 now uses iwl_mac_conf_tx.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With mac80211's help to call stop() and start() in mac80211
suspend/resume function, both iwlagn and iwl3945 no longer calling
stop() and start(); remove un-necessary STATUS_IN_SUSPEND bit from both
header files and functions,

Move apm_ops.stop() function into pci_suspend() to ensure
DMA is stopped before go into suspend mode.

iwl3945 has the similar suspend/resume function as iwlagn, so move both
functions to iwlcore to be shared by both drivers.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

p54spi_tx_frame wasn't waiting for HOST_ALLOWED in SPI_ADRS_DMA_WRITE_CTRL.
This resulted in frequent 'WR_READY timeout' on beacon resubmission.

Also don't free skb on error path, as it gets freed on p54spi_wq_tx.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Acked-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CMD_MESH_CONFIG command ID and a couple of structure members in TxPD,
RxPD have been changed in firmware version 10.x.y.z and newer.
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of firmware itself p54_upload_firmware was sending to the device
content of struct firmware and the following random garbage.

Notice '&' before priv->firmware->data at p54spi_spi_write.
But simple removing of '&' sign triggered BUG_ON at dma_cache_maint.
Thus kmemdup - kfree workaround.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Mask value read from SPI_ADRS_DMA_WRITE_CTRL in p54spi_wait_bit.
 Without this, 'fw_upload not allowed to DMA write' is observed at both N800 and N810.
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Acked-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a hang on resume when the filesystem is not
available and request_firmware blocks.

However, the device does not accept the firmware on resume.
and it will exit with:

> firmware part 1 upload failed (-71).
> device is in a bad state. please reconnect it!
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

swap mwl8k_remove and mwl8k_shutdown functions to allow
"rmmod mwl8k; modprobe mwl8k"
Signed-off-by: NJoerg Albert <jal2@gmx.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch deactivates powersave in station mode.

It does not work correctly yet, so the code does more harm than good.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"not" is not printed without a space after %pM
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After suspend & resume the rt2x00 devices won't wakeup
anymore due to a broken register information setup.
The most important problem is the release of the EEPROM
buffer which is completely cleared and never read again
after the suspend.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

arm will pad even between u8's, so mark the structs/unions
packed. Fixes a build bug on arm due to BUILD_BUG_ON tests
in the code.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Reported-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the value read from HERMES_RID_TXQUEUEEMPTY becomes 0 after exactly
100 readings, we wrongly consider it a timeout.  Rewrite the clever
while loop as a for loop that does the right thing and looks simpler.

Reported by Juha Leppanen <juha_motorsportcom@luukku.com>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In a scenario where there isn't any firmware available, we will have a
double kfree of rt2x00dev->spec.channels_info when ieee80211_register_hw
returns an error status inside rt2x00lib_probe_hw.

The problem is that if ieee80211_register_hw fails, we call
rt2x00lib_remove_hw twice:
* first inside rt2x00lib_probe_hw upon failure of ieee80211_register_hw
* error status is returned to rt2x00lib_probe_dev, which then sees it and
  calls in this case rt2x00lib_remove_dev that will again run
  rt2x00lib_remove_hw

Prevent this avoiding calling rt2x00lib_remove_hw inside
rt2x00lib_probe_hw

Problem was detected with CONFIG_DEBUG_PAGEALLOC=y, CONFIG_SLUB_DEBUG=y,
CONFIG_SLUB_DEBUG_ON=y, that dumps this with no firmware available:

rt61pci 0000:00:07.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
wmaster0 (rt61pci): not using net_device_ops yet
phy0: Selected rate control algorithm 'pid'
phy0: Failed to initialize wep: -2
phy0 -> rt2x00lib_probe_dev: Error - Failed to initialize hw.
=============================================================================
BUG kmalloc-128: Object already free
-----------------------------------------------------------------------------

INFO: Allocated in rt61pci_probe_hw+0x3e5/0x6e0 [rt61pci] age=340 cpu=0 pid=21
INFO: Freed in rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib] age=0 cpu=0 pid=21
INFO: Slab 0xc13ac3e0 objects=23 used=10 fp=0xdd59f6e0 flags=0x400000c3
INFO: Object 0xdd59f6e0 @offset=1760 fp=0xdd59f790

Bytes b4 0xdd59f6d0:  15 00 00 00 b2 8a fb ff 5a 5a 5a 5a 5a 5a 5a 5a ....².ûÿZZZZZZZZ
  Object 0xdd59f6e0:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f6f0:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f700:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f710:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f720:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f730:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f740:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
  Object 0xdd59f750:  6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b a5 kkkkkkkkkkkkkkk¥
 Redzone 0xdd59f760:  bb bb bb bb                                     »»»»
 Padding 0xdd59f788:  5a 5a 5a 5a 5a 5a 5a 5a                         ZZZZZZZZ
Pid: 21, comm: stage1 Not tainted 2.6.29.1-desktop-1.1mnb #1
Call Trace:
 [<c01abbb3>] print_trailer+0xd3/0x120
 [<c01abd37>] object_err+0x37/0x50
 [<c01acf57>] __slab_free+0xe7/0x2f0
 [<c01ad1de>] kfree+0x7e/0xd0
 [<e0e4a239>] ? rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib]
 [<e0e4a239>] ? rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib]
 [<e0e4a239>] rt2x00lib_remove_hw+0x59/0x70 [rt2x00lib]
 [<e0e4acc7>] rt2x00lib_remove_dev+0x37/0x50 [rt2x00lib]
 [<e0e4b087>] rt2x00lib_probe_dev+0x1a7/0x3b0 [rt2x00lib]
 [<e0eb288f>] rt2x00pci_probe+0xdf/0x1ee [rt2x00pci]
 [<c026b9ee>] local_pci_probe+0xe/0x10
 [<c026c750>] pci_device_probe+0x60/0x80
 [<c02d5c2a>] driver_probe_device+0x9a/0x2e0
 [<c02d5ef9>] __driver_attach+0x89/0x90
 [<c02d541b>] bus_for_each_dev+0x4b/0x70
 [<c026c690>] ? pci_device_remove+0x0/0x40
 [<c02d59d9>] driver_attach+0x19/0x20
 [<c02d5e70>] ? __driver_attach+0x0/0x90
 [<c02d4cef>] bus_add_driver+0x1cf/0x2a0
 [<c026c690>] ? pci_device_remove+0x0/0x40
 [<c02d60c9>] driver_register+0x69/0x140
 [<c026c9b0>] __pci_register_driver+0x40/0x80
 [<e0ecc000>] ? rt61pci_init+0x0/0x19 [rt61pci]
 [<e0ecc017>] rt61pci_init+0x17/0x19 [rt61pci]
 [<c0101116>] do_one_initcall+0x26/0x1c0
 [<c01ab90c>] ? slab_pad_check+0x3c/0x120
 [<c01ab90c>] ? slab_pad_check+0x3c/0x120
 [<c01ac8da>] ? check_object+0xda/0x210
 [<c01b0026>] ? percpu_free+0x46/0x50
 [<c01ad09e>] ? __slab_free+0x22e/0x2f0
 [<c01b0026>] ? percpu_free+0x46/0x50
 [<c01b0026>] ? percpu_free+0x46/0x50
 [<c01b0026>] ? percpu_free+0x46/0x50
 [<c01687ec>] ? stop_machine_destroy+0x3c/0x40
 [<c015e515>] ? load_module+0xa5/0x1c50
 [<e0ec5000>] ? rt61pci_eepromregister_read+0x0/0x40 [rt61pci]
 [<e0eb2000>] ? rt2x00pci_write_tx_data+0x0/0x90 [rt2x00pci]
 [<c03ac2fb>] ? mutex_lock+0xb/0x20
 [<c03ac2fb>] ? mutex_lock+0xb/0x20
 [<c017ad16>] ? tracepoint_update_probe_range+0x76/0xa0
 [<c017ad6f>] ? tracepoint_module_notify+0x2f/0x40
 [<c03b02ed>] ? notifier_call_chain+0x2d/0x70
 [<c014f0ed>] ? __blocking_notifier_call_chain+0x4d/0x60
 [<c014f11a>] ? blocking_notifier_call_chain+0x1a/0x20
 [<c0160156>] sys_init_module+0x96/0x1d0
 [<c019dad6>] ? sys_munmap+0x46/0x60
 [<c0105546>] syscall_call+0x7/0xb
FIX kmalloc-128: Object at 0xdd59f6e0 not freed
rt61pci 0000:00:07.0: PCI INT A disabled
rt61pci: probe of 0000:00:07.0 failed with error -2
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I forgot that iwl3945 registration is separate from iwlagn.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The assertion of the lock-bit in the hardware register is unreliable,
because there are devices with quirks that will randomly set the bit.

Do the assertion in software, only.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds a new device to ar9170usb.
Reported-by: NMike Kershaw/Dragorn <dragorn@kismetwireless.net>
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Code was clearly wrong, plus callers expect the mode change to happen as
soon as possible, not dropped on the floor until the next time some
other config value changes and a commit happens.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add USB device ID for OQO 01+'s internal wireless LAN

An OQO employee mentions the chip's true identity here:-
    ftp://ftp.oqo.com/unsupported/linux/OQOLinux.htmlSigned-off-by: NJamie Lentin <jm@lentin.co.uk>
Acked-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't lead memory when receive errors
Signed-off-by: NPhilip Rakity <prakity@yahoo.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes the following waring:
> ------------[ cut here ]------------
>WARNING: at kernel/softirq.c:138 local_bh_enable+0x54/0xbc()
>Modules linked in: p54spi
>[<c0034ff8>] (dump_stack+0x0/0x14)
>[<c005b1a4>] (warn_on_slowpath+0x0/0x68)
>[<c00604c8>] (local_bh_enable+0x0/0xbc)
>[<bf000000>] (p54spi_op_tx+0x0/0x4c [p54spi])
>[<c01a4d34>] (p54_sta_unlock+0x0/0x78)

p54spi_op_tx needs to be called from different locking contexts.
Therefore we have to protect the linked list with irqsave spinlocks.
Reported-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I'm very sorry, as this change belongs to the other patch:
"[PATCH] p54: fix SoftLED compile dependencies".
however I must have somehow lost "git add" for that file.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The RX buffer poison needs to be refreshed, if we recycle an RX buffer,
because it might be (partially) overwritten by some DMA operations.

Cc: stable@kernel.org
Cc: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>