This replaces a 2-D search through an array with a simple 8-bit table
lookup for determining the actual and/or base page size for a HPT entry.

The encoding in the second doubleword of the HPTE is designed to encode
the actual and base page sizes without using any more bits than would be
needed for a 4k page number, by using between 1 and 8 low-order bits of
the RPN (real page number) field to encode the page sizes.  A single
"large page" bit in the first doubleword indicates that these low-order
bits are to be interpreted like this.

We can determine the page sizes by using the low-order 8 bits of the RPN
to look up a 256-entry table.  For actual page sizes less than 1MB, some
of the upper bits of these 8 bits are going to be real address bits, but
we can cope with that by replicating the entries for those smaller page
sizes.

While we're at it, let's move the hpte_page_size() and hpte_base_page_size()
functions from a KVM-specific header to a header for 64-bit HPT systems,
since this computation doesn't have anything specifically to do with KVM.
Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

KVM devices were manipulating list data structures without any form of
synchronization, and some implementations of the create operations also
suffered from a lack of synchronization.

Now when we've split the xics create operation into create and init, we
can hold the kvm->lock mutex while calling the create operation and when
manipulating the devices list.

The error path in the generic code gets slightly ugly because we have to
take the mutex again and delete the device from the list, but holding
the mutex during anon_inode_getfd or releasing/locking the mutex in the
common non-error path seemed wrong.
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Acked-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

As we are about to hold the kvm->lock during the create operation on KVM
devices, we should move the call to xics_debugfs_init into its own
function, since holding a mutex over extended amounts of time might not
be a good idea.

Introduce an init operation on the kvm_device_ops struct which cannot
fail and call this, if configured, after the device has been created.
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>

When using if_changed, we need to add FORCE as a dependency (see
Documentation/kbuild/makefiles.txt) otherwise we don't get command line
change checking amongst other things. This has resulted in vdsos not
being rebuilt when switching between big and little endian.

The vdso64/32ld commands have to be changed around to avoid pulling
FORCE into the linker command line (code copied from x86).
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When we introduced the little endian support, we added the endian flags
to CC directly using override. I don't know the history of why we did
that, I suspect no one does.

Although this mostly works, it has one bug, which is that CROSS32CC
doesn't get -mbig-endian. That means when the compiler is little endian
by default and the user is building big endian, vdso32 is incorrectly
compiled as little endian and the kernel fails to build.

Instead we can add the endian flags to cflags-y/aflags-y, and then
append those to KBUILD_CFLAGS/KBUILD_AFLAGS.

This has the advantage of being 1) less ugly, 2) the documented way of
adding flags in the arch Makefile and 3) it fixes building vdso32 with a
LE toolchain.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We cannot do those initializations from apply_feature_fixups() as
this function runs in a very restricted environment on 32-bit where
the kernel isn't running at its linked address and the PTRRELOC()
macro must be used for any global accesss.

Instead, split them into a separtate steup_feature_keys() function
which is called in a more suitable spot on ppc32.

Fixes: 309b315b ("powerpc: Call jump_label_init() in apply_feature_fixups()")
Reported-and-tested-by: NChristian Kujau <lists@nerdbynature.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We don't identify the machine type anymore...
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This makes it easier to debug crashes that happen very early before
the kernel takes over Open Firmware by allowing us to relate the OF
reported crashing addresses to offsets within the kernel.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Commit 8d460f61 ("powerpc/process: Add the function
flush_tmregs_to_thread") added flush_tmregs_to_thread() and included
the assumption that it would only be called for a task which is not
current.

Although this is correct for ptrace, when generating a core dump, some
of the routines which call flush_tmregs_to_thread() are called. This
leads to a WARNing such as:

  Not expecting ptrace on self: TM regs may be incorrect
  ------------[ cut here ]------------
  WARNING: CPU: 123 PID: 7727 at arch/powerpc/kernel/process.c:1088 flush_tmregs_to_thread+0x78/0x80
  CPU: 123 PID: 7727 Comm: libvirtd Not tainted 4.8.0-rc1-gcc6x-g61e8a0d5 #1
  task: c000000fe631b600 task.stack: c000000fe63b0000
  NIP: c00000000001a1a8 LR: c00000000001a1a4 CTR: c000000000717780
  REGS: c000000fe63b3420 TRAP: 0700   Not tainted  (4.8.0-rc1-gcc6x-g61e8a0d5)
  MSR: 900000010282b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]>  CR: 28004222  XER: 20000000
  ...
  NIP [c00000000001a1a8] flush_tmregs_to_thread+0x78/0x80
  LR [c00000000001a1a4] flush_tmregs_to_thread+0x74/0x80
  Call Trace:
   flush_tmregs_to_thread+0x74/0x80 (unreliable)
   vsr_get+0x64/0x1a0
   elf_core_dump+0x604/0x1430
   do_coredump+0x5fc/0x1200
   get_signal+0x398/0x740
   do_signal+0x54/0x2b0
   do_notify_resume+0x98/0xb0
   ret_from_except_lite+0x70/0x74

So fix flush_tmregs_to_thread() to detect the case where it is called on
current, and a transaction is active, and in that case flush the TM regs
to the thread_struct.

This patch also moves flush_tmregs_to_thread() into ptrace.c as it is
only called from that file.

Fixes: 8d460f61 ("powerpc/process: Add the function flush_tmregs_to_thread")
Signed-off-by: NCyril Bur <cyrilbur@gmail.com>
[mpe: Flesh out change log]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Commit 7aef4136 ("powerpc32: rewrite csum_partial_copy_generic()
based on copy_tofrom_user()") introduced a bug when destination
address is odd and initial csum is not null

In that (rare) case the initial csum value has to be rotated one byte
as well as the resulting value is

This patch also fixes related comments

Fixes: 7aef4136 ("powerpc32: rewrite csum_partial_copy_generic() based on copy_tofrom_user()")
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The generic allocation code may sometimes decide to assign a prefetchable
64-bit BAR to the M32 window. In fact it may also decide to allocate
a 64-bit non-prefetchable BAR to the M64 one ! So using the resource
flags as a test to decide which window was used for PE allocation is
just wrong and leads to insane PE numbers.

Instead, compare the addresses to figure it out.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Rename the function as agreed by Ben & Gavin]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When machine check occurs with MSR(RI=0), it means MC interrupt is
unrecoverable and kernel goes down to panic path. But the console
message still shows it as recovered. This patch fixes the MCE console
messages.

Fixes: 36df96f8 ("powerpc/book3s: Decode and save machine check event.")
Signed-off-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The recent commit 63a72284 ("powerpc/pci: Assign fixed PHB number
based on device-tree properties"), added code to read a 64-bit property
from the device tree, and if not found read a 32-bit property (reg).

There was a bug in the 32-bit case, on big endian machines, due to the
use of the 64-bit value to read the 32-bit property. The cast of &prop
means we end up writing to the high 32-bit of prop, leaving the low
32-bits containing whatever junk was on the stack.

If that junk value was non-zero, and < MAX_PHBS, we would end up using
it as the PHB id. This results in users seeing what appear to be random
PHB ids.

Fix it by reading into a u32 property and then assigning that to the
u64 value, letting the CPU do the correct conversions for us.

Fixes: 63a72284 ("powerpc/pci: Assign fixed PHB number based on device-tree properties")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This is a very minor/trivial fix for the output of PCI address on EEH
logs. The PCI address on "OF node" field currently is using ":" as a
separator for the function, but the usual separator is ".". This patch
changes the separator to dot, so the PCI address is printed as usual.
Signed-off-by: NGuilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Some powerpc builds fail with the following buld error.

  In file included from ./arch/powerpc/include/asm/mmu_context.h:11:0,
                   from arch/powerpc/kernel/vdso.c:28:
  arch/powerpc/include/asm/cputhreads.h: In function 'get_tensr':
  arch/powerpc/include/asm/cputhreads.h:101:2: error:
  	implicit declaration of function 'cpu_has_feature'

Fixes: b92a226e ("powerpc: Move cpu_has_feature() to a separate file")
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch fixes the following warning:
arch/powerpc/platforms/pseries/hotplug-memory.c:323:29: error: 'lmb_to_memblock' defined but not used [-Werror=unused-function]
static struct memory_block *lmb_to_memblock(struct of_drconf_cell *lmb)
                           ^~~~~~~~~~~~~~~

The only consumer of this function is 'dlpar_remove_lmb', which is
enabled with CONFIG_MEMORY_HOTREMOVE, so move it into the same
ifdef block.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The current implementation of MCE early handling modifies CR0/1 registers
without saving its old values. Fix this by moving early check for
powersaving mode to machine_check_handle_early().

The power architecture 2.06 or later allows the possibility of getting
machine check while in nap/sleep/winkle. The last bit of HSPRG0 is set
to 1, if thread is woken up from winkle. Hence, clear the last bit of
HSPRG0 (r13) before MCE handler starts using it as paca pointer.

Also, the current code always puts the thread into nap state irrespective
of whatever idle state it woke up from. Fix that by looking at
paca->thread_idle_state and put the thread back into same state where it
came from.

Fixes: 1c51089f ("powerpc/book3s: Return from interrupt if coming from evil context.")
Reported-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Reviewed-by: NShreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Move IDLE_STATE_ENTER_SEQ macro to cpuidle.h so that MCE handler changes
in subsequent patch can use it.

No functionality change.
Signed-off-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The function pnv_restore_hyp_resource() loads the TOC into r2 from
the invalid PACA pointer before fixing r13 value. This do not affect
POWER ISA 3.0 but it does have an impact on POWER ISA 2.07 or less
leading CPU to get stuck forever.

	login: [  471.830433] Processor 120 is stuck.

This can be easily reproducible using following steps:
- Turn off SMT
	$ ppc64_cpu --smt=off
- offline/online any online cpu (Thread 0 of any core which is online)
	$ echo 0 > /sys/devices/system/cpu/cpu<num>/online
	$ echo 1 > /sys/devices/system/cpu/cpu<num>/online

For POWER ISA 2.07 or less, the last bit of HSPRG0 is set indicating
that thread is waking up from winkle. Hence, the last bit of HSPRG0(r13)
needs to be clear before accessing it as PACA to avoid loading invalid
values from invalid PACA pointer.

Fix this by loading TOC after r13 register is corrected.

Fixes: bcef83a0 ("powerpc/powernv: Add platform support for stop instruction")
Signed-off-by: NMahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: NVaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Commit fd141d1a ("powerpc/powernv/pci: Rework accessing the TCE
invalidate register") broke TCE invalidation on IODA2/PHB3 for real
mode.

This makes invalidate work again.

Fixes: fd141d1a ("powerpc/powernv/pci: Rework accessing the TCE invalidate register")
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We should return -ENOMEM if alloc_spu_gang() fails.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This sets the type of the interrupt appropriately. We set it as follow:

 - If not mapped from the device-tree, we use edge. This is the case
of the virtual interrupts and PCI MSIs for example.

 - If mapped from the device-tree and #interrupt-cells is 2 (PAPR
compliant), we use the second cell to set the appropriate type

 - If mapped from the device-tree and #interrupt-cells is 1 (current
OPAL on P8 does that), we assume level sensitive since those are
typically going to be the PSI LSIs which are level sensitive.

Additionally, we mark the interrupts requested via the opal_interrupts
property all level. This is a bit fishy but the best we can do until we
fix OPAL to properly expose them with a complete descriptor. It is also
correct for the current HW anyway as OPAL interrupts are currently PCI
error and PSI interrupts which are level.

Finally now that edge interrupts are properly identified, we can enable
CONFIG_HARDIRQS_SW_RESEND which will make the core re-send them if
they occur while masked, which some drivers rely upon.

This fixes issues with lost interrupts on some Mellanox adapters.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch utilises the GENERIC_CPU_AUTOPROBE infrastructure
to automatically load the crc32c-vpmsum module if the CPU supports
it.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Commit 817820b0 ("powerpc/iommu: Support "hybrid" iommu/direct DMA
ops for coherent_mask < dma_mask) adds a check of coherent_dma_mask for
dma allocations.

Unfortunately current PASemi code does not set this value for the DMA
engine, which ends up with the default value of 0xffffffff, the result
is on a PASemi system with >2Gb ram and iommu enabled the the onboard
ethernet stops working due to an inability to allocate memory. Add an
initialisation to pci_dma_dev_setup_pasemi().
Signed-off-by: NDarren Stevens <darren@stevens-zone.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We should set the error code here rather than incorrectly returning 0.
Otherwise static checkers complain.

Link: http://lkml.kernel.org/r/20160804053525.GM775@mwandaSigned-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The stringify_in_c() macro may not be included. Make the dependency
explicit.

Link: http://lkml.kernel.org/r/564720c5328edd53c9d56db325be7215440eec3e.1467837322.git.jbaron@akamai.comSigned-off-by: NJason Baron <jbaron@akamai.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Joe Perches <joe@perches.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer.  Thus the pointer can point to const data.
However the attributes do not have to be a bitfield.  Instead unsigned
long will do fine:

1. This is just simpler.  Both in terms of reading the code and setting
   attributes.  Instead of initializing local attributes on the stack
   and passing pointer to it to dma_set_attr(), just set the bits.

2. It brings safeness and checking for const correctness because the
   attributes are passed by value.

Semantic patches for this change (at least most of them):

    virtual patch
    virtual context

    @r@
    identifier f, attrs;

    @@
    f(...,
    - struct dma_attrs *attrs
    + unsigned long attrs
    , ...)
    {
    ...
    }

    @@
    identifier r.f;
    @@
    f(...,
    - NULL
    + 0
     )

and

    // Options: --all-includes
    virtual patch
    virtual context

    @r@
    identifier f, attrs;
    type t;

    @@
    t f(..., struct dma_attrs *attrs);

    @@
    identifier r.f;
    @@
    f(...,
    - NULL
    + 0
     )

Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.comSigned-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NVineet Gupta <vgupta@synopsys.com>
Acked-by: NRobin Murphy <robin.murphy@arm.com>
Acked-by: NHans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We want to initialise register_process_table() before ppc_md is setup,
so that it can be called as part of MMU init (at least on Radix ATM).

That no longer works because probe_machine() requires that ppc_md be
empty before it's called, and we now do probe_machine() much later.

So make register_process_table a global for now. It will probably move
into a mmu_radix_ops struct at some point in the future.

This was broken by me when applying commit 7025776e "powerpc/mm:
Move hash table ops to a separate structure" due to conflicts with other
patches.

Fixes: 7025776e ("powerpc/mm: Move hash table ops to a separate structure")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

These have been changed in the hardware, update Linux's version.
Signed-off-by: NMadhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Commit 9402c684 ("powerpc: Factor do_feature_fixup calls")
introduced a subtle bug on 32-bit. When reading the cpu spec from the
global, we not only need to do a pointer relocation on the global
address but also on the pointer we read from it.

This fixes crashes reported on MPC5200 based machines.

Fixes: 9402c684 ("powerpc: Factor do_feature_fixup calls")
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

 - Remove check for parallel PHY

 - Set LP-Serial Register Map type

[akpm@linux-foundation.org: fix build]
[alexandre.bounine@idt.com: fix build fix]
 Link: http://lkml.kernel.org/r/20160802184932.2755-1-alexandre.bounine@idt.com
Link: http://lkml.kernel.org/r/1469125134-16523-13-git-send-email-alexandre.bounine@idt.comSigned-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Barry Wood <barry.wood@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Current definition of map_inb() mport operations callback uses u32 type
to specify required inbound window (IBW) size.  This is limiting factor
because existing hardware - tsi721 and fsl_rio, both support IBW size up
to 16GB.

Changing type of size parameter to u64 to allow IBW size configurations
larger than 4GB.

[alexandre.bounine@idt.com: remove compiler warning about size of constant]
  Link: http://lkml.kernel.org/r/20160802184856.2566-1-alexandre.bounine@idt.com
Link: http://lkml.kernel.org/r/1469125134-16523-11-git-send-email-alexandre.bounine@idt.comSigned-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Barry Wood <barry.wood@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In general, there's no need for the "restore sigmask" flag to live in
ti->flags.  alpha, ia64, microblaze, powerpc, sh, sparc (64-bit only),
tile, and x86 use essentially identical alternative implementations,
placing the flag in ti->status.

Replace those optimized implementations with an equally good common
implementation that stores it in a bitfield in struct task_struct and
drop the custom implementations.

Additional architectures can opt in by removing their
TIF_RESTORE_SIGMASK defines.

Link: http://lkml.kernel.org/r/8a14321d64a28e40adfddc90e18a96c086a6d6f9.1468522723.git.luto@kernel.orgSigned-off-by: NAndy Lutomirski <luto@kernel.org>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>	[powerpc]
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dmitry Safonov <dsafonov@virtuozzo.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For pure bool function's return value, bool is a little better more or
less than int.

Link: http://lkml.kernel.org/r/1469331815-2026-1-git-send-email-chengang@emindsoft.com.cnSigned-off-by: NChen Gang <gang.chen.5i5j@gmail.com>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There was only one use of __initdata_refok and __exit_refok

__init_refok was used 46 times against 82 for __ref.

Those definitions are obsolete since commit 312b1485 ("Introduce new
section reference annotations tags: __ref, __refdata, __refconst")

This patch removes the following compatibility definitions and replaces
them treewide.

/* compatibility defines */
#define __init_refok     __ref
#define __initdata_refok __refdata
#define __exit_refok     __ref

I can also provide separate patches if necessary.
(One patch per tree and check in 1 month or 2 to remove old definitions)

[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1466796271-3043-1-git-send-email-fabf@skynet.beSigned-off-by: NFabian Frederick <fabf@skynet.be>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Introduce a new KVM capability, KVM_CAP_PPC_HTM, that can be queried to
determine if a PowerPC KVM guest should use HTM (Hardware Transactional
Memory).

This will be used by QEMU to populate the pa-features bits in the
guest's device tree.
Signed-off-by: NSam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

This patch enables support for Performance monitor registers related
ELF core note NT_PPC_PMU based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding one new register sets REGSET_PMU in powerpc
corresponding to the ELF core note sections added in this
regard. It also implements the get, set and active functions
for this new register sets added.
Signed-off-by: NAnshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch enables support for EBB state registers related
ELF core note NT_PPC_EBB based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding one new register sets REGSET_EBB in powerpc
corresponding to the ELF core note sections added in this
regard. It also implements the get, set and active functions
for this new register sets added.
Signed-off-by: NAnshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch enables support for running TAR, PPR, DSCR registers
related ELF core notes NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR based
ptrace requests through PTRACE_GETREGSET, PTRACE_SETREGSET calls.
This is achieved through adding three new register sets REGSET_TAR,
REGSET_PPR, REGSET_DSCR in powerpc corresponding to the ELF core
note sections added in this regad. It implements the get, set and
active functions for all these new register sets added.
Signed-off-by: NAnshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch enables support for all three TM checkpointed SPR
states related ELF core note  NT_PPC_TM_CTAR, NT_PPC_TM_CPPR,
NT_PPC_TM_CDSCR based ptrace requests through PTRACE_GETREGSET,
PTRACE_SETREGSET calls. This is achieved through adding three
new register sets REGSET_TM_CTAR, REGSET_TM_CPPR and
REGSET_TM_CDSCR in powerpc corresponding to the ELF core note
sections added. It implements the get, set and active functions
for all these new register sets added.
Signed-off-by: NAnshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>