This corrects a race with the PHY RST bit not being set properly if the
PLL status changes right before timeout. This resulted in it potentially
failing even if the device came up in time.

Special thanks to Mr. Juha Leppanen and Iwamatsu-san for reporting this
out and reviewing it.
Reported-by: NJuha Leppanen <juha_motorsportcom@luukku.com>
Reviewed-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Tested-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There were a number of issues with the DSP context save/restore code,
mostly left-over relics from when it was introduced on SH3-DSP with
little follow-up testing, resulting in things like task_pt_dspregs()
referencing incorrect state on the stack.

This follows the MIPS convention of tracking the DSP state in the
thread_struct and handling the state save/restore in switch_to() and
finish_arch_switch() respectively. The regset interface is also updated,
which allows us to finally be rid of task_pt_dspregs() and the special
cased task_pt_regs().
Signed-off-by: NMichael Trimarchi <michael@evidence.eu.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

First argument unused since 2.3.11.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Forcing direct-mapped worked on certain older 2-way set associative
parts, but was always error prone on 4-way parts. As these are the
norm these days, there is not much point in continuing to support this
mode. Most of the folks that used direct-mapped mode generally just
wanted writethrough caching in the first place..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

cpuidle wants ARCH_HAS_DEFAULT_IDLE defined in order to use the
default idle loop. So, make it accessible and enable it for all
sh machines.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds a 'noiotrap' kernel command line option to permit disabling of
I/O trapping. This is mostly useful for running on emulators where the
physical device limitations are not an issue.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Triggers -Werror on gcc-4.3:

arch/sh/kernel/setup.c: In function 'early_parse_mem':
arch/sh/kernel/setup.c:111: error: format not a string literal and no format arguments
...
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Formatting and typo fix.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Impact: cleanup

It's unused, since about 1995.  So remove all initialization of it in
preparation for actually removing the field.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Acked-by: NThomas Gleixner <tglx@linutronix.de>

Older versions of kexec-tools has a zImage loader that
passes a virtual address as entry point. The elf loader
otoh it passes a physical address as entry point, and
pages are always passed as physical addresses as well.

Only allow physical addresses from now on.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Save and restore ftrace state when returning from kexec jump in
machine_kexec(). Follows the x86 change.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

For the time being, this creates far more problems than it solves,
evident by the second local_irq_disable(). Kill all of this off
and rely on IRQ disabling to protect against the VBR reload.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add kexec jump support to the SuperH architecture.

Similar to the x86 implementation, with the following
exceptions:

- Instead of separating the assembly code flow into
two parts for regular kexec and kexec jump we use a
single code path. In the assembly snippet regular
kexec is just kexec jump that never comes back.

- Instead of using a swap page when moving data between
pages the page copy assembly routine has been modified
to exchange the data between the pages using registers.

- We walk the page list twice in machine_kexec() to
do and undo physical to virtual address conversion.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Rework the kexec code to avoid using P2SEG. Instead
we walk the page list in machine_kexec() and convert
the addresses from physical to virtual using C.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Setup the vbr register in machine_kexec(). This
instead of passing values to the assembly snippet.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds support for extended ASIDs (up to 16-bits) on newer SH-X3 cores
that implement the PTAEX register and respective functionality. Presently
only the 65nm SH7786 (90nm only supports legacy 8-bit ASIDs).

The main change is in how the PTE is written out when loading the entry
in to the TLB, as well as in how the TLB entry is selectively flushed.

While SH-X2 extended mode splits out the memory-mapped U and I-TLB data
arrays for extra bits, extended ASID mode splits out the address arrays.
While we don't use the memory-mapped data array access, the address
array accesses are necessary for selective TLB flushes, so these are
implemented newly and replace the generic SH-4 implementation.

With this, TLB flushes in switch_mm() are almost non-existent on newer
parts.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch fixes a possible problem in the resume from
hibenration. It temporaneally saves the clk->rate on the
stack to avoid any possible change during the clk->set_parent(..)
call.
Signed-off-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch contains CONFIG_SUSPEND support to the SuperH
architecture. If enabled, SuperH Mobile processors will
register their suspend callbacks during boot.

To suspend, use "echo mem > /sys/power/state". To allow
wakeup, make sure "/sys/device/platform/../power/wakeup"
contains "enabled". Additional per-device driver patches
are most likely needed.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

-- log --
arch/sh/kernel/cpu/sh4/../sh3/entry.S:365: Error: invalid operands for opcode
make[4]: *** [arch/sh/kernel/cpu/sh4/../sh3/entry.o] Error 1
make[3]: *** [arch/sh/kernel/cpu/sh4] Error 2
-- log --
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds PM support to the clock framework.
With this, resume from hibernation is properly supported.
Signed-off-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds the clk_set_parent/clk_get_parent routines to the sh
clock framework.
Signed-off-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.

P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add Suspend-to-disk / swsusp / CONFIG_HIBERNATION support
to the SuperH architecture.

To suspend, use "swapon /dev/sda2; echo disk > /sys/power/state"
To resume, pass "resume=/dev/sda2" on the kernel command line.

The patch "pm: rework includes, remove arch ifdefs V2" is
needed to allow the generic swsusp code to build properly.

Hibernation is not enabled with this patch though, a patch
setting ARCH_HIBERNATION_POSSIBLE will be submitted later.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Follow the conversions as per the other subtypes.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert over the SH7263 IRQ groups as well.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Follow the conversions as per the other subtypes.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This was accidentally dropped in the multiple vectors per irq conversion.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.

This fixes potential irq masking issues for sh7763 hardware
blocks such as RTC/SCIF/DMAC/GETHER/PCIC5/MMCIF/SIM/GPIO/USBF.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds preliminary support for the SH7786 CPU subtype.

While this is a dual-core CPU, only UP is supported for now. L2 cache
support is likewise not yet implemented.

More information on this particular CPU subtype is available at:

	http://www.renesas.com/fmwk.jsp?cnt=sh7786_root.jsp&fp=/products/mpumcu/superh_family/sh7780_series/sh7786_group/Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>