Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 19 6月, 2013 16 次提交
  3. 15 6月, 2013 13 次提交
  5. 10 6月, 2013 1 次提交
    • K
      ARM: EXYNOS: no more support non-DT for EXYNOS SoCs · 383ffda2
      由 Kukjin Kim 提交于 
      As we discussed in mailing list, non-DT for EXYNOS SoCs will not be
supported from v3.11. This patch removes regarding files for non-DT
including board files and defconfig.

Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
      383ffda2
  7. 08 6月, 2013 2 次提交
    • D
      ARM: exynos: add debug_ll_io_init() call in exynos_init_io() · 9c1fcdcc
      由 Doug Anderson 提交于 
      If the early MMU mapping of the UART happens to get booted out of the
TLB between the start of paging_init() and when we finally re-add the
UART at the very end of s3c_init_cpu(), we'll get a hang at bootup if
we've got early_printk enabled.  Avoid this hang by calling
debug_ll_io_init() early.

Without this patch, you can reliably reproduce a hang when early
printk is enabled by adding flush_tlb_all() at the start of
exynos_init_io().  After this patch the hang goes away.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>
      9c1fcdcc
    • T
      ARM: EXYNOS: uncompress - print debug messages if DEBUG_LL is defined · 437d8ac5
      由 Tushar Behera 提交于 
      Printing low-level debug messages make an assumption that the specified
UART port has been preconfigured by the bootloader. Incorrectly
specified UART port results in system getting stalled while printing the
message "Uncompressing Linux... done, booting the kernel"
This UART port number is specified through S3C_LOWLEVEL_UART_PORT. Since
the UART port might different for different board, it is not possible to
specify it correctly for every board that use a common defconfig file.

Calling this print subroutine only when DEBUG_LL fixes the problem. By
disabling DEBUG_LL in default config file, we would be able to boot
multiple boards with different default UART ports.

With this current approach, we miss the print "Uncompressing Linux...
done, booting the kernel." when DEBUG_LL is not defined.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>
      437d8ac5
  9. 06 6月, 2013 1 次提交
    • P
      arch, mm: Remove tlb_fast_mode() · 29eb7782
      由 Peter Zijlstra 提交于 
      Since the introduction of preemptible mmu_gather TLB fast mode has been
broken. TLB fast mode relies on there being absolutely no concurrency;
it frees pages first and invalidates TLBs later.

However now we can get concurrency and stuff goes *bang*.

This patch removes all tlb_fast_mode() code; it was found the better
option vs trying to patch the hole by entangling tlb invalidation with
the scheduler.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Reported-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      29eb7782
  11. 04 6月, 2013 1 次提交
  13. 03 6月, 2013 4 次提交
  15. 29 5月, 2013 1 次提交
  17. 28 5月, 2013 1 次提交