Simple LAN device for debug or management purposes.
Device supports interrupts for RX and TX(completion).
Device does not have DMA ability.
Signed-off-by: NNoam Camus <noamc@ezchip.com>
Signed-off-by: NTal Zilcer <talz@ezchip.com>
Acked-by: NAlexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Below case causes mii bus probe failed:
ifconfig eth0 down -> suspend/resume with Mega/fax mix off -> ifconfig eth0 up

In i.MX6SX/i.MX7D chip, Mega/fast mix off feature is supported that means most of
SOC power will be off including ENET MAC for power saving. Once ENET MAC power
off, all initialized MAC registers reset to default, so in the case, it must
init MAC prior to mii bus probe.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While IEEE and CEE use the same structure to store apps, the selector
and priority fields for both are different. Only the priority field is
explained, add documentation explaining how the selector field differs
for both.

cgdcbxd code shows an example of how selector fields differ.
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This particular BUG_ON condition was checking for attr set err in the
COMMIT phase, which isn't expected (it's a driver bug if PREPARE phase is
OK but COMMIT fails).  But BUG_ON() is too strong for this case, so change
to WARN().  BUG_ON() would be warranted if the system was corrupted beyond
repair, but this is not the case here.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Scott Feldman says:

====================
switchdev; add VLAN support for port's bridge_getlink

One more missing piece of the puzzle.  Add vlan dump support to switchdev
port's bridge_getlink.  iproute2 "bridge vlan show" cmd already knows how
to show the vlans installed on the bridge and the device , but (until now)
no one implemented the port vlan part of the netlink PF_BRIDGE:RTM_GETLINK
msg.  Before this patch, "bridge vlan show":

	$ bridge -c vlan show
	port    vlan ids
	sw1p1    30-34			<< bridge side vlans
		 57

	sw1p1				<< device side vlans (missing)

	sw1p2    57

	sw1p2

	sw1p3

	sw1p4

	br0     None

(When the port is bridged, the output repeats the vlan list for the vlans
on the bridge side of the port and the vlans on the device side of the
port.  The listing above show no vlans for the device side even though they
are installed).

After this patch:

	$ bridge -c vlan show
	port    vlan ids
	sw1p1    30-34			<< bridge side vlan
		 57

	sw1p1    30-34			<< device side vlans
		 57
		 3840 PVID

	sw1p2    57

	sw1p2    57
		 3840 PVID

	sw1p3    3842 PVID

	sw1p4    3843 PVID

	br0     None
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One more missing piece of the puzzle.  Add vlan dump support to switchdev
port's bridge_getlink.  iproute2 "bridge vlan show" cmd already knows how
to show the vlans installed on the bridge and the device , but (until now)
no one implemented the port vlan part of the netlink PF_BRIDGE:RTM_GETLINK
msg.  Before this patch, "bridge vlan show":

	$ bridge -c vlan show
	port    vlan ids
	sw1p1    30-34			<< bridge side vlans
		 57

	sw1p1				<< device side vlans (missing)

	sw1p2    57

	sw1p2

	sw1p3

	sw1p4

	br0     None

(When the port is bridged, the output repeats the vlan list for the vlans
on the bridge side of the port and the vlans on the device side of the
port.  The listing above show no vlans for the device side even though they
are installed).

After this patch:

	$ bridge -c vlan show
	port    vlan ids
	sw1p1    30-34			<< bridge side vlan
		 57

	sw1p1    30-34			<< device side vlans
		 57
		 3840 PVID

	sw1p2    57

	sw1p2    57
		 3840 PVID

	sw1p3    3842 PVID

	sw1p4    3843 PVID

	br0     None

I re-used ndo_dflt_bridge_getlink to add vlan fill call-back func.
switchdev support adds an obj dump for VLAN objects, using the same
call-back scheme as FDB dump.  Support included for both compressed and
un-compressed vlan dumps.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use vid_begin/end to be consistent with BRIDGE_VLAN_INFO_RANGE_BEGIN/END.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove handling of tx_ring in prb_setup_retire_blk_timer
for TPACKET_V3 because init_prb_bdqc is called only for zero tx_ring
and thus prb_setup_retire_blk_timer for zero tx_ring only.

And also in functon init_prb_bdqc there is no usage of tx_ring.
Thus removing tx_ring from init_prb_bdqc.
Signed-off-by: NManinder Singh <maninder1.s@samsung.com>
Suggested-by: NFrans Klaver <fransklaver@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it.  And there is
no value in anyone else taking over updating it either.

However the references to it continue to spread as boiler plate text
from one Kconfig file into the next.  We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.

No code is changed in this commit, just Kconfig help text.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Heiko Stuebner says:

====================
net: stmmac: dwmac-rk: add support for rk3368

Apart from small cleanups, this series provides support for the dwmac
on the new rk3368 ARM64 soc.

Tested on a R88 board using a RMII phy.

Changes since v1:
- Adapt to changes resulting from patch d42202dc ("net: stmmac:
dwmac-rk: Don't add function name in info or err messages")
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add constants and callback functions for the dwmac on rk3368 socs.
As can be seen, the base structure is the same, only registers and
the bits in them moved slightly.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mac settings like RGMII/RMII, speeds etc are done in the so called
"General Register Files", contain numerous other settings as well and
always seem to change between Rockchip SoCs. Therefore abstract the
register accesses into a per-soc ops struct to make this reusable on
other Rockchip SoCs.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first iteration of the dwmac-rk support did access an intermediate
clock directly below the pll selector. This was removed in a subsequent
revision, but the clock and one invocation remained. This results in
the driver trying to set the rate of a non-existent clock when the soc
and not some external source provides the phy clock for RMII phys.

So set the rate of the correct clock and remove the remaining now
completely unused definition.

Fixes: 436f5ae08f9d ("GMAC: add driver for Rockchip RK3288 SoCs integrated GMAC")
Cc: stable@vger.kernel.org
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a first version the driver did want to do some gpio wiggling, which
of course never made it into the kernel, but somehow these register
defines where forgotten. Remove them, as they shouldn't be here.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Zero the statistics counters when setting up the global
registers. Otherwise the counters will remain from the last boot if
the power has not been removed.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
debugfs for mv88e6xxx

This patchset adds some debugfs files for seeing into a mv88e6xxx
family of switch chips.

DB   T/P  Vec State Addr
003  Port 008   7   00:22:02:00:18:44
003  Port 008   6   80:ee:73:83:60:27
005  Port 020   7   94:10:3e:80:bc:f3
0f8  Port 001   6   8e:25:13:53:44:de

This walks all possible entries, so is a bit slow, but is always
correct.

Target Port
   0   15
   1   15
   2   15
   3   15
   4   15
   5   15
   6   15
   7   15
   8   15
   9   15
-->snip<--
  31   15

A rather boring example, since i only have one switch here. But this shows
the routing between multiple switches.

    GLOBAL GLOBAL2   0    1    2    3    4    5    6
 0:  c804       0  1e4f 100f 100f 1e4f 1e0f  e07  e07
 1:    fe       0     3    3    3    3    3 c03e c03f
 2:     0    ffff     0    0    0    0    0    0    0
 3:     0    ffff  1721 1721 1721 1721 1721 1721 1721
 4:  6000     258   433  431  431  433  433 373f  433
 5:     0      ff     0    0    0    0    0    0    0
 6:  c000    1f0f  2026 2025 2023 3020 4020 501f 6020
 7:     0    707f     0    0    0    0    0    0    0
 8:     0    7800  2080 2080 2080 2080 2080 2080 2080
 9:     0    1600     1    1    1    1    1    1    1
 a:   148       0     0    0    0    0    0    0    0
 b:  4000    1000     1    2    4    8   10   20   40
 c:     0      7f     0    0    0    0    0    0    0
 d:  ffff     5f3     0    0    0    0    0    0    0
 e:  ffff       6     0    0    0    0    0    0    0
 f:  ffff     f00  dada dada dada dada dada dada dada
10:     0       0     0    0    0    0    0    0    0
11:     0       0     0    0    0    0    0    0    0
12:  5555       0     0    0    0    0    0    0    0
13:  5555       0    1a    0    0 1df0    0 1e07    0
14:  aaaa     400     0    0    0    0    0    0    0
15:  aaaa       0     0    0    0    0    0    0    0
16:  ffff       0  6011 6011 6011 6011   33   33    0
17:  ffff       0     0    0    0    0    0    0    0
18:  fa41    1844  3210 3210 3210 3210 3210 3210 3210
19:     0     1e1  7654 7654 7654 7654 7654 7654 7654
1a:  5550       0     0    0    0    0    0    0    0
1b:   1fb    f869  8000 8000 8000 8000 8000 8000 8000
1c:     0       0     0    0    0    0    0    0    0
1d:   c00       0     0    0    0    0    0    0    0
1e:     0       0     0    0    0    0    0    0    0
1f:     0       0     0    0    0    0    0    0    0

All the switch registers which are directly accessible.

      Statistic       Port  0  Port  1  Port  2  Port  3  Port  4  Port  5  Port 6
     in_good_octets:     2176        0        0  4263711        0   499540       0
      in_bad_octets:    46050        0        0    50196        0        0       0
         in_unicast:        0        0        0     7693        0     7691       0
      in_broadcasts:        0        0        0        0        0        3       0
      in_multicasts:       34        0        0        0        0       27       0
           in_pause:        0        0        0        0        0        0       0
       in_undersize:        0        0        0        0        0        0       0
       in_fragments:       45        0        0        2        0        0       0
        in_oversize:        0        0        0        0        0        0       0
          in_jabber:        0        0        0        0        0        0       0
        in_rx_error:        0        0        0        0        0        0       0
       in_fcs_error:      159        0        0       37        0        0       0
         out_octets:      808        0        0   496608      336  4267159       0
        out_unicast:        0        0        0     7691        0     7693       0
     out_broadcasts:        1        0        0        3        0        0       0
     out_multicasts:        9        0        0        6        4       34       0
          out_pause:        0        0        0        0        0        0       0
          excessive:        0        0        0        0        0        0       0
         collisions:        0        0        0        0        0        0       0
           deferred:        0        0        0        0        0        0       0
             single:        0        0        0        0        0        0       0
           multiple:        0        0        0        0        0        0       0
      out_fcs_error:        0        0        0        0        0        0       0
               late:        0        0        0        0        0        0       0
       hist_64bytes:       36        0        0     7577        0     7574       0
   hist_65_127bytes:       53        0        0      241        4      298       0
  hist_128_255bytes:       50        0        0       12        0       10       0
  hist_256_511bytes:       43        0        0        8        0        2       0
 hist_512_1023bytes:       18        0        0     7573        0     7564       0
hist_1024_max_bytes:        3        0        0       19        0        0       0
     sw_in_discards:        0        0        0        0        0        0       0
     sw_in_filtered:        0        0        0        0        0        0       0
    sw_out_filtered:       34        0        0     7693        0     7721       0

Of particular interest here is that you get to see all ports,
including the CPU port and any DSA ports. You cannot get statistics
for these ports via ethtool.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the contents of the scratch registers to be shown in debugfs.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device map is used to route packets between cascaded switches.
Add dumping a switches device map via debugfs.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the contents of the statistics counters to be shown in debugfs.
This is particularly useful for the cpu and dsa ports, which cannot be
seen using ethtools -S.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the code to retrieve a statistics counter into a function of its
own, so it can later be reused.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dump the Address Translation Unit via a file in debugfs.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the contents of the registers to be shown in debugfs.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the driver understand adapter version 2.

Cc: Rachel Lunnon <rachel_lunnon@stormagic.com>
Signed-off-by: NGuolin Yang <gyang@vmware.com>
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If rcd length was zero, the page used for frag was not being released. It
was being replaced with a newly allocated page. This change takes care
of that memory leak.
Signed-off-by: NGuolin Yang <gyang@vmware.com>
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement a handler for pci shutdown so that the driver has an
opportunity to make sure that device is quiesced before the PCI
switches to legacy IRQs. This way the possibility of
"screaming interrupt" is avoided.
Acked-by: NShrikrishna Khare <skhare@vmware.com>
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add code to nf_unregister_hook to flush the nf_queue when a hook is
unregistered.  This guarantees that the pointer that the nf_queue code
retains into the nf_hook list will remain valid while a packet is
queued.

I tested what would happen if we do not flush queued packets and was
trivially able to obtain the oops below.  All that was required was
to stop the nf_queue listening process, to delete all of the nf_tables,
and to awaken the nf_queue listening process.

> BUG: unable to handle kernel paging request at 0000000100000001
> IP: [<0000000100000001>] 0x100000001
> PGD b9c35067 PUD 0
> Oops: 0010 [#1] SMP
> Modules linked in:
> CPU: 0 PID: 519 Comm: lt-nfqnl_test Not tainted
> task: ffff8800b9c8c050 ti: ffff8800ba9d8000 task.ti: ffff8800ba9d8000
> RIP: 0010:[<0000000100000001>]  [<0000000100000001>] 0x100000001
> RSP: 0018:ffff8800ba9dba40  EFLAGS: 00010a16
> RAX: ffff8800bab48a00 RBX: ffff8800ba9dba90 RCX: ffff8800ba9dba90
> RDX: ffff8800b9c10128 RSI: ffff8800ba940900 RDI: ffff8800bab48a00
> RBP: ffff8800b9c10128 R08: ffffffff82976660 R09: ffff8800ba9dbb28
> R10: dead000000100100 R11: dead000000200200 R12: ffff8800ba940900
> R13: ffffffff8313fd50 R14: ffff8800b9c95200 R15: 0000000000000000
> FS:  00007fb91fc34700(0000) GS:ffff8800bfa00000(0000) knlGS:0000000000000000
> CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
> CR2: 0000000100000001 CR3: 00000000babfb000 CR4: 00000000000007f0
> Stack:
>  ffffffff8206ab0f ffffffff82982240 ffff8800bab48a00 ffff8800b9c100a8
>  ffff8800b9c10100 0000000000000001 ffff8800ba940900 ffff8800b9c10128
>  ffffffff8206bd65 ffff8800bfb0d5e0 ffff8800bab48a00 0000000000014dc0
> Call Trace:
>  [<ffffffff8206ab0f>] ? nf_iterate+0x4f/0xa0
>  [<ffffffff8206bd65>] ? nf_reinject+0x125/0x190
>  [<ffffffff8206dee5>] ? nfqnl_recv_verdict+0x255/0x360
>  [<ffffffff81386290>] ? nla_parse+0x80/0xf0
>  [<ffffffff8206c42c>] ? nfnetlink_rcv_msg+0x13c/0x240
>  [<ffffffff811b2fec>] ? __memcg_kmem_get_cache+0x4c/0x150
>  [<ffffffff8206c2f0>] ? nfnl_lock+0x20/0x20
>  [<ffffffff82068159>] ? netlink_rcv_skb+0xa9/0xc0
>  [<ffffffff820677bf>] ? netlink_unicast+0x12f/0x1c0
>  [<ffffffff82067ade>] ? netlink_sendmsg+0x28e/0x650
>  [<ffffffff81fdd814>] ? sock_sendmsg+0x44/0x50
>  [<ffffffff81fde07b>] ? ___sys_sendmsg+0x2ab/0x2c0
>  [<ffffffff810e8f73>] ? __wake_up+0x43/0x70
>  [<ffffffff8141a134>] ? tty_write+0x1c4/0x2a0
>  [<ffffffff81fde9f4>] ? __sys_sendmsg+0x44/0x80
>  [<ffffffff823ff8d7>] ? system_call_fastpath+0x12/0x6a
> Code:  Bad RIP value.
> RIP  [<0000000100000001>] 0x100000001
>  RSP <ffff8800ba9dba40>
> CR2: 0000000100000001
> ---[ end trace 08eb65d42362793f ]---

Cc: stable@vger.kernel.org
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currenlty nf_tables chains added in one network namespace are being
run in all network namespace.  The issues are myriad with the simplest
being an unprivileged user can cause any network packets to be dropped.

Address this by simply not running nf_tables chains in the wrong
network namespace.

Cc: stable@vger.kernel.org
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Macvtap should be compatible with tuntap for
maximum number of queues.

commit 'baf71c5c (tuntap:
Increase the number of queues in tun.)' removes
the limitations and increases number of queues in tuntap.
Now, Its safe to increase number of queues in Macvtap as well.

This patch also modifies 'macvtap_del_queues' function
to avoid extra memory allocation in stack.

Changes from v1->v2 :
Michael S. Tsirkin, Jason Wang  :
                  Better way to use linked list to
avoid use of extra memory in stack.
Sergei Shtylyov : Specify dependent commit's summary.
Signed-off-by: NPankaj Gupta <pagupta@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BPF offers another way to generate latency histograms. We attach
kprobes at trace_preempt_off and trace_preempt_on and calculate the
time it takes to from seeing the off/on transition.

The first array is used to store the start time stamp. The key is the
CPU id. The second array stores the log2(time diff). We need to use
static allocation here (array and not hash tables). The kprobes
hooking into trace_preempt_on|off should not calling any dynamic
memory allocation or free path. We need to avoid recursivly
getting called. Besides that, it reduces jitter in the measurement.

CPU 0
      latency        : count     distribution
       1 -> 1        : 0        |                                        |
       2 -> 3        : 0        |                                        |
       4 -> 7        : 0        |                                        |
       8 -> 15       : 0        |                                        |
      16 -> 31       : 0        |                                        |
      32 -> 63       : 0        |                                        |
      64 -> 127      : 0        |                                        |
     128 -> 255      : 0        |                                        |
     256 -> 511      : 0        |                                        |
     512 -> 1023     : 0        |                                        |
    1024 -> 2047     : 0        |                                        |
    2048 -> 4095     : 166723   |*************************************** |
    4096 -> 8191     : 19870    |***                                     |
    8192 -> 16383    : 6324     |                                        |
   16384 -> 32767    : 1098     |                                        |
   32768 -> 65535    : 190      |                                        |
   65536 -> 131071   : 179      |                                        |
  131072 -> 262143   : 18       |                                        |
  262144 -> 524287   : 4        |                                        |
  524288 -> 1048575  : 1363     |                                        |
CPU 1
      latency        : count     distribution
       1 -> 1        : 0        |                                        |
       2 -> 3        : 0        |                                        |
       4 -> 7        : 0        |                                        |
       8 -> 15       : 0        |                                        |
      16 -> 31       : 0        |                                        |
      32 -> 63       : 0        |                                        |
      64 -> 127      : 0        |                                        |
     128 -> 255      : 0        |                                        |
     256 -> 511      : 0        |                                        |
     512 -> 1023     : 0        |                                        |
    1024 -> 2047     : 0        |                                        |
    2048 -> 4095     : 114042   |*************************************** |
    4096 -> 8191     : 9587     |**                                      |
    8192 -> 16383    : 4140     |                                        |
   16384 -> 32767    : 673      |                                        |
   32768 -> 65535    : 179      |                                        |
   65536 -> 131071   : 29       |                                        |
  131072 -> 262143   : 4        |                                        |
  262144 -> 524287   : 1        |                                        |
  524288 -> 1048575  : 364      |                                        |
CPU 2
      latency        : count     distribution
       1 -> 1        : 0        |                                        |
       2 -> 3        : 0        |                                        |
       4 -> 7        : 0        |                                        |
       8 -> 15       : 0        |                                        |
      16 -> 31       : 0        |                                        |
      32 -> 63       : 0        |                                        |
      64 -> 127      : 0        |                                        |
     128 -> 255      : 0        |                                        |
     256 -> 511      : 0        |                                        |
     512 -> 1023     : 0        |                                        |
    1024 -> 2047     : 0        |                                        |
    2048 -> 4095     : 40147    |*************************************** |
    4096 -> 8191     : 2300     |*                                       |
    8192 -> 16383    : 828      |                                        |
   16384 -> 32767    : 178      |                                        |
   32768 -> 65535    : 59       |                                        |
   65536 -> 131071   : 2        |                                        |
  131072 -> 262143   : 0        |                                        |
  262144 -> 524287   : 1        |                                        |
  524288 -> 1048575  : 174      |                                        |
CPU 3
      latency        : count     distribution
       1 -> 1        : 0        |                                        |
       2 -> 3        : 0        |                                        |
       4 -> 7        : 0        |                                        |
       8 -> 15       : 0        |                                        |
      16 -> 31       : 0        |                                        |
      32 -> 63       : 0        |                                        |
      64 -> 127      : 0        |                                        |
     128 -> 255      : 0        |                                        |
     256 -> 511      : 0        |                                        |
     512 -> 1023     : 0        |                                        |
    1024 -> 2047     : 0        |                                        |
    2048 -> 4095     : 29626    |*************************************** |
    4096 -> 8191     : 2704     |**                                      |
    8192 -> 16383    : 1090     |                                        |
   16384 -> 32767    : 160      |                                        |
   32768 -> 65535    : 72       |                                        |
   65536 -> 131071   : 32       |                                        |
  131072 -> 262143   : 26       |                                        |
  262144 -> 524287   : 12       |                                        |
  524288 -> 1048575  : 298      |                                        |

All this is based on the trace3 examples written by
Alexei Starovoitov <ast@plumgrid.com>.
Signed-off-by: NDaniel Wagner <daniel.wagner@bmw-carit.de>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When STP is running in user-space and querier is configured, the
querier timer is not started when a port goes to a non-blocking state.
This patch unifies the user- and kernel-space stp multicast port enable
path and enables it in all states different from blocking. Note that when a
port goes in BR_STATE_DISABLED it's not enabled because that is handled
in the beginning of the port list loop.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFC 4.2 2nd pull request

This one only contains a one liner fix for a typo that I
introduced while cleaning some of the nfcmrvl patches that
were part of the 1st 4.2 pull request.

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2015-06-18

Here's the final bluetooth-next pull request for 4.2.

 - Cleanups & fixes to 802.15.4 code and related drivers
 - Fix btusb driver memory leak
 - New USB IDs for Atheros controllers
 - Support for BCM4324B3 UART based Broadcom controller
 - Fix for Bluetooth encryption key size handling
 - Broadcom controller initialization fixes
 - Support for Intel controller DDC parameters
 - Support for multiple Bluetooth LE advertising instances
 - Fix for HCI user channel cleanup path

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Actor and Partner details can be accessed via proc-fs, sys-fs
entries or netlink interface. These interfaces are world readable
at this moment. The earlier patch-series made the LACP communication
secure to avoid nuisance attack from within the same L2 domain but
it did not prevent "someone unprivileged" looking at that information
on host and perform the same act.

This patch essentially avoids spitting those entries if the user
in question does not have enough privileges.
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nicolas Ferre says:

====================
net/macb: add sama5d2 support

This series is basically the support for another flavor of the GEM IP
configuration. It ended up being a series because of some little fixes made to
the binding documentation before adding the new compatibility string.

Bye,

v2: - fix bindings
    - add sama5d2 compatibility string to the binding documentation
====================
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the compatible string for Atmel sama5d2 SoC family as the configuration
options differ from other instances of the GEM.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add sama5d2 to the biding documentation for this use of the GEM IP.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On sama5d4, we only have a GEM IP that is configured to do 10/100 Mbits. So the
use of "Gigabit" can be confusing.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the driver and the DT bindings we use the "atmel" prefix. Fix it in the
binding documentation.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

inet_diag_dump_reqs() is called from inet_diag_dump_icsk() with BH
disabled. So no need to disable BH in inet_diag_dump_reqs().
Signed-off-by: NHiroaki Shimoda <shimoda.hiroaki@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL8211F has different register definitions from RTL8211E.
Specially it needs to enable TXDLY in case of RGMII.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>