[Blackfin] arch: punt the simple ad5304 spi driver now that the generic spidev driver lets you do it from userspace
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

 - set default u-boot partition size to 256k
 - modify the offset with the size change
 - use mtd defines (append for offset and full for size)
   where applicable rather than churning constants when we dont have to
Signed-off-by: NGrace Pan <grace.pan@analog.com>
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

 - Enable kernel generic spidev driver for blackfin SPI ADC
 - spi_adc driver, document and test sample not synced
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

 - Buttons on the BF533-STAMP board are not inverted
 - Fix spurious GPIO Interrupt caused during set irq_type for edge triggered interrupts
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>

Signed-off-by: NMike Frysinger <michael.frysinger@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>

[Blackfin] arch: enable generic GPIO based I2C driver in STAMP-BF533, EZKIT-BF533 and EZKIT-BF561 boards
Signed-off-by: NBryan Wu <bryan.wu@analog.com>

[Blackfin] arch: replace current blackfin specific pfbutton driver with kernel generic gpio key driver
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>

Signed-off-by: NMike Frysinger <michael.frysinger@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>

Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time

 - move this static things to the blackfin board file
 - add pin_req array to struct bfin5xx_spi_master
 - tested on BF537/BF548 with SPI flash
Signed-off-by: NBryan Wu <bryan.wu@analog.com>

Changes:

1. The baud for spi mmc defined in board file is not used by the old
spi driver. A slower value from spi framework is used instead. In latest
bug fixing, the correct baud is use which is too high for spi MMC card.

2. SPI is enabled only after DMA is started.

3. MMC detection IRQ is set to 55.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>

Blackfin arch: use "char bfin_board_name[]" rather than "char *bfin_board_name" per discussion on lkml as the former uses less storage
Signed-off-by: NMike Frysinger <michael.frysinger@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>

Signed-off-by: NBryan Wu <bryan.wu@analog.com>

Signed-off-by: NMike Frysinger <michael.frysinger@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>

Blackfin arch: move board specific setup out of common init code and into the board specific init code
Signed-off-by: NMike Frysinger <michael.frysinger@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds support for the Analog Devices Blackfin processor architecture, and
currently supports the BF533, BF532, BF531, BF537, BF536, BF534, and BF561
(Dual Core) devices, with a variety of development platforms including those
avaliable from Analog Devices (BF533-EZKit, BF533-STAMP, BF537-STAMP,
BF561-EZKIT), and Bluetechnix!  Tinyboards.

The Blackfin architecture was jointly developed by Intel and Analog Devices
Inc.  (ADI) as the Micro Signal Architecture (MSA) core and introduced it in
December of 2000.  Since then ADI has put this core into its Blackfin
processor family of devices.  The Blackfin core has the advantages of a clean,
orthogonal,RISC-like microprocessor instruction set.  It combines a dual-MAC
(Multiply/Accumulate), state-of-the-art signal processing engine and
single-instruction, multiple-data (SIMD) multimedia capabilities into a single
instruction-set architecture.

The Blackfin architecture, including the instruction set, is described by the
ADSP-BF53x/BF56x Blackfin Processor Programming Reference
http://blackfin.uclinux.org/gf/download/frsrelease/29/2549/Blackfin_PRM.pdf

The Blackfin processor is already supported by major releases of gcc, and
there are binary and source rpms/tarballs for many architectures at:
http://blackfin.uclinux.org/gf/project/toolchain/frs There is complete
documentation, including "getting started" guides available at:
http://docs.blackfin.uclinux.org/ which provides links to the sources and
patches you will need in order to set up a cross-compiling environment for
bfin-linux-uclibc

This patch, as well as the other patches (toolchain, distribution,
uClibc) are actively supported by Analog Devices Inc, at:
http://blackfin.uclinux.org/

We have tested this on LTP, and our test plan (including pass/fails) can
be found at:
http://docs.blackfin.uclinux.org/doku.php?id=testing_the_linux_kernel

[m.kozlowski@tuxland.pl: balance parenthesis in blackfin header files]
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: NAubrey Li <aubrey.li@analog.com>
Signed-off-by: NJie Zhang <jie.zhang@analog.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>